Belden HIRSCHMANN SPIDER II User manual

Installation SPIDER II
Release 07 10/2013
Technical support
https://hirschmann-support.belden.eu.com
User Manual
Installation
Industrial Ethernet Rail Switch
SPIDER II, SPIDER II Giga, SPIDER II PoE
SPIDER II 8TX
SPIDER II 8TX EEC
SPIDER II 8TX/1FX EEC
SPIDER II 8TX/1FX-SM EEC
SPIDER II 8TX/1FX-ST EEC
SPIDER II 8TX/2FX EEC
SPIDER II 8TX/2FX-SM EEC
SPIDER II 8TX/2FX-ST EEC SPIDER II Giga 5T/2S EEC SPIDER II Giga 5T EEC
SPIDER II 8TX PoE
SP
SP
SP
SP
SP
SP
SP
SP
SP
SP
P
1
2
3
4
5
6
7
8

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2013 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD/DVD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
Installation 039 709-001-07-1013 - 22.10.13

Installation SPIDER II
Release 07 10/2013 3
Contents
Safety instructions 5
About this Manual 9
Legend 10
1 Description 10
1.1 General device description 10
1.2 Description of the device variants 10
1.3 Ethernet ports 15
1.3.1 10/100 Mbit/s twisted pair port 15
1.3.2 10/100 Mbit/s PoE port 15
1.3.3 10/100/1000 Mbit/s twisted pair port 16
1.3.4 100 Mbit/s F/O port 16
1.3.5 1000 Mbit/s F/O port 17
1.4 Display elements 17
1.4.1 Device state 17
1.4.2 Port state 17
2 Installation 18
2.1 Unpacking the package and checking the content 19
2.2 Installing an SFP transceiver (optional) 19
2.3 Connecting the terminal block for the supply voltage and the
grounding 20
2.4 Mounting the device on the DIN rail 20
2.5 Installing the terminal block, start-up procedure 21
2.6 Connecting network cables 22
2.6.1 10/100 Mbit/s twisted pair port 22
1.3.2 10/100 Mbit/s PoE port 15
2.6.3 10/100/1000 Mbit/s twisted pair port 22
2.6.4 100 Mbit/s F/O port 22
2.6.5 1000 Mbit/s F/O port 22
3 Maintenance and service 23

4Installation SPIDER II
Release 07 10/2013
4Disassembly 23
4.1 Removing the device from the DIN rail 23
4.1.1 SPIDER II without PoE 23
4.1.2 SPIDER II 8TX PoE 24
4.2 Removing the SFP transceivers 24
5 Technical data 25
A Further Support 35

Installation SPIDER II
Release 07 10/2013 5
Safety instructions
Correct usage
Only use the device for those purposes specified in the catalog and in the
technical description. Only operate the device with external devices and
components that are recommended and permitted by the manufacturer.
The proper and safe operation of this product depends on proper handling
during transport, proper storage, assembly and installation, and
conscientious operation and maintenance procedures.
Supply voltage
The power supply inputs are designed for operation with safety extra-
low voltage. Solely connect SELV circuits with voltage restrictions in
line with IEC/EN 60950-1 to the supply voltage connections.
Use undamaged parts.
If you are operating the module with an external voltage, only supply
the system with a safety extra-low voltage in compliance with IEC/EN
60950-1.
Connect the ground connector before you set up the other
connections. When removing the connections, you remove the ground
connector last.
Relevant for North America: To be used in class 2 circuits.
The device may only be connected to a supply voltage of class 2 that
fulfills the requirements of the National Electrical Code, Table 11(b).
Relevant for North America: For use in Class 2 circuits
Use copper wire/conductors of class 1 60/75 °C or 75 °C or 90 °C
exclusively.
Relevant for North America
for devices certified for hazardous locations:
Power, input and output (I/O) wiring must be in accordance with
Class I, Division 2 wiring methods [Article 501-4(b) of the National
Electrical Code, NFPA 70] and in accordance with the authority having
jurisdiction.
Only switch on the device when the housing is closed.
CAUTION
ELECTRIC SHOCK
Solely connect a supply voltage that corresponds to the type plate of your
device.
Failure to follow these instructions can result in injury or equipment
damage.

6Installation SPIDER II
Release 07 10/2013
Shielding ground
Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.
Housing
Only technicians authorized by the manufacturer are permitted to open
the housing.
Note: The device is grounded by means of a 3-pin terminal block.
Verify that the electrical installation meets locally or nationally
applicable safety regulations.
The device must be installed in the vertical position.
If installed in a living area or office environment, the device must be
operated exclusively in switch cabinets with fire protection
characteristics in accordance with EN 60950-1.
CAUTION
ELECTRIC SHOCK
Solely connect a supply voltage that corresponds to the type plate of your
device.
Never insert sharp objects (small screwdrivers, wires, etc.) into the inside of
the device.
Failure to follow these instructions can result in injury or equipment
damage.
CAUTION
OVERHEATING OF THE DEVICE
When installing the device, ensure that the ventilation slots are not covered.
Make sure there is at least 10 cm (3.94 in) of space.
Failure to follow these instructions can result in injury or equipment
damage.

Installation SPIDER II
Release 07 10/2013 7
Environment
Only operate the device at the specified ambient temperature
(temperature of the surrounding air at a distance of up to 5 cm from the
device) and at the specified relative humidity.
When you are selecting the installation location, make sure you
observe the climatic threshold values specified in the technical data.
Use the device in an environment with a maximum pollution degree
that complies with the specifications in the technical data.
The equipment is designed for in building installation only and is not
intended to be connected to exposed (outside plant) networks.
Qualification requirements for personnel
Qualified personnel as understood in this manual and the warning signs,
are persons who are familiar with the setup, assembly, startup, and
operation of this product and are appropriately qualified for their job. This
includes, for example, those persons who have been:
trained or directed or authorized to switch on and off, to ground and to
label power circuits and devices or systems in accordance with current
safety engineering standards;
trained or directed in the care and use of appropriate safety equipment
in accordance with the current standards of safety engineering;
trained in providing first aid.
General safety instructions
This device is operated by electricity. You must follow precisely the
prescribed safety requirements for the voltage connections in this
document.
See “Supply voltage” on page 5.
Non-observance of these safety instructions can cause material damage
and/or injuries.
Only appropriately qualified personnel should work on this device or in
its vicinity. The personnel must be thoroughly familiar with all the
warnings and maintenance procedures outlined in this operating
manual.
The proper and safe operation of this device depends on proper
handling during transportation, proper storage and assembly, and
conscientious operation and maintenance procedures.
Never start operation with damaged components.
Only use the devices in accordance with this manual. In particular,
observe all warnings and safety-related information.
Any work that may be required on the electrical installation may only
be carried out by personnel trained for this purpose.

8Installation SPIDER II
Release 07 10/2013
Relevant for SPIDER II 8 TX/...FX... EEC and SPIDER II Giga 5T/2S
EEC:
Note: LED or LASER components in compliance with IEC 60825-1
(2007):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT
National and international safety regulations
Make sure that the electrical installation meets local or nationally
applicable safety regulations.
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
2004/108/EC (EMC)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic
compatibility.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
The device can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55022
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.
Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.

Installation SPIDER II
Release 07 10/2013 9
E marking
The labeled devices comply with the regulations contained in the following
European directive(s):
72/245/EWG, 2009/19/EG
Guideline for standardizing the regulations of member states relating to
radio interference from motor vehicles. Certified devices are marked with
an e1 type approval indicator.
Rule No. 10 of the Economic Commission for Europe (ECE): Devices with
a certification are labelled with the E type-approval mark.
Note: For use in connection with a suitable type approved power supply
only.
FCC note
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate high
frequencies, and if it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a living area can also cause interference, and in this case
the user is obliged to cover the costs of removing the interference.
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

10 Installation SPIDER II
Release 07 10/2013
About this Manual
The “Installation User Manual” document contains a device description,
safety instructions, a display description and other information that you
require to install the device before starting with the configuration of the
device.
Legend
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading