Belden Hirschmann RED25 Series User manual

Installation RED25
Release 01 02/2015
Technical support
https://hirschmann-support.belden.eu.com
User Manual
Installation
Redundancy Switch
RED25

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2015 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD/DVD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
Installation RED25 040 068-001-01-0215 -20.02.2015

Installation RED25
Release 01 02/2015 3
Contents
Safety instructions 5
About this manual 11
Key 11
1 Description 12
1.1 General description 12
1.2 Device name and product code 13
1.3 Device views 16
1.4 Power supply 17
1.5 Ethernet ports 17
1.5.1 10/100 Mbit/s twisted pair port 17
1.5.2 100 Mbit/s F/O port (optional) 18
1.6 Display elements 18
1.6.1 Device state 18
1.6.2 Port state 19
1.7 Management interfaces 19
1.7.1 V.24 interface (external management) 19
1.7.2 USB interface 20
1.8 Signal contact 21
2 Installation 22
2.1 Checking the package contents 22
2.2 Installing and grounding the device 22
2.2.1 Installing the device onto the DIN rail 23
2.2.2 Grounding the device 23
2.3 Installing an SFP transceiver (optional) 23
2.4 Connecting the power supply and signal lines 24
2.5 Operating the device 26
2.6 Connecting data cables 26
2.7 Filling out the inscription label 26
3 Making basic settings 27
4 Monitoring the ambient air temperature 28

4Installation RED25
Release 01 02/2015
5 Maintenance and service 29
6Disassembly 30
6.1 Removing the device 30
6.2 Removing an SFP transceiver (optional) 31
7 Technical data 32
A Further Support 39

Installation RED25
Release 01 02/2015 5
Safety instructions
General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful opera-
tion and maintenance procedures.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a damaged
or malfunctioning the device, turn off the supply voltage and return the
device to Hirschmann for inspection.
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
Intended usage
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product only according to the technical specifications.
See “Technical data” on page 32.
Connect to the product only components suitable for the requirements
of the specific application case.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

6Installation RED25
Release 01 02/2015
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
Grounding the device
Grounding the device is by means of a separate ground connection on the
device.
Ground the device before connecting any other cables.
Disconnect the grounding only after disconnecting all other cables.
The overall shield of a connected shielded twisted pair cable is connected
to the ground connector on the front panel as a conductor.
Requirements for connecting electrical conductors
Before connecting the electrical conductors, always verify that all of
the requirements listed are fulfilled:
All of the following requirements are fulfilled:
The electrical wires are voltage-free.
The cables used are permitted for the temperature range of the application case.
Relevant for North America:
Use 60/75 or 75 °C copper (Cu) wire only.
Table 1: General requirements for connecting electrical conductors
All of the following requirements are fulfilled:
The voltage connected meets the requirements for a safety extra-low voltage (SELV) as per
IEC/EN 60950-1.
The connected voltage is limited by a current limitation device or a fuse.
Observe the electrical threshold values for the signal contact.
See “General technical data” on page 32.
Table 2: Requirements for connecting the signal contact
Relevance Requirements
Absolutely relevant All of the following requirements are fulfilled:
The supply voltage corresponds to the voltage specified on the
type plate of the device.
The power supply conforms to overvoltage category I or II.
The power supply has an easily accessible disconnecting device
(e.g., a switch or a plug). This disconnecting device is clearly iden-
tified. So in the case of an emergency, it is clear which discon-
necting device belongs to which power supply cable.
The wire diameter of the power supply cable is at least 0.75 mm²
(North America: AWG18) on the supply voltage input.
The cross-section of the ground conductor is the same size as or
bigger than the cross-section of the power supply cables.
Table 3: Requirements for connecting the supply voltage

Installation RED25
Release 01 02/2015 7
Relevant when the
device is supplied via 1
voltage input
The following requirements are alternatively fulfilled:
Alternative 1 The voltage supply meets the requirements for a
limited power source (LPS) as per EN 60950-1.
Alternative 2 Relevant for North America:
The voltage supply meets the requirements as
per NEC Class 2
Alternative 3 All of the following requirements are fulfilled:
The voltage supply meets the requirements
for a safety extra-low voltage (SELV) as per
IEC/EN 60950-1.
Supply with DC voltage:
A fuse suitable for DC voltage is located in
the plus conductor of the power supply.
The minus conductor is on ground potential.
Otherwise, a fuse is also located in the minus
conductor.
Regarding the properties of this fuse:
See “General technical data” on page 32.
Supply with AC voltage:
A fuse is located in the outer conductor of the
power supply.
The neutral conductor is on ground potential.
Otherwise, a fuse is also located in the
neutral conductor.
Regarding the properties of this fuse:
See “General technical data” on page 32.
Relevance Requirements
Table 3: Requirements for connecting the supply voltage

8Installation RED25
Release 01 02/2015
Supply voltage
The supply voltage is only connected with the chassis via protective
elements.
Installation site requirements
Verify that there is at least 4 in (10 cm) of space above and below the
device.
Verify that there is at least 0.8 in (2 cm) of space on the right and left
sides of the device.
Install the device in a fire protected enclosure according to
EN 60950-1.
Relevant when the
device is supplied via 2
voltage inputs
The following requirements are alternatively fulfilled:
Alternative 1 The total voltage supply meets the requirements
for a limited power source (LPS) as per EN
60950-1.
Alternative 2 Relevant for North America:
The total voltage supply meets the requirements
as per NEC Class 2.
Alternative 3 All of the following requirements are fulfilled:
The voltage supply meets the requirements
for a safety extra-low voltage (SELV) as per
IEC/EN 60950-1.
Supply with DC voltage:
A fuse suitable for DC voltage is located at
both voltage inputs in the plus conductor of
the power supply.
The minus conductor is on ground potential
at both voltage inputs. Otherwise, a fuse is
also located in the minus conductor.
Regarding the properties of this fuse:
See “General technical data” on page 32.
Supply with AC voltage:
A fuse is located at both voltage inputs in the
outer conductor of the power supply.
The neutral conductor is on ground potential
at both voltage inputs. Otherwise, a fuse is
also located in the neutral conductor.
Regarding the properties of this fuse:
See “General technical data” on page 32.
Relevance Requirements
Table 3: Requirements for connecting the supply voltage

Installation RED25
Release 01 02/2015 9
Housing
Only technicians authorized by the manufacturer are permitted to open
the housing.
Never insert pointed objects (narrow screwdrivers, wires, etc.) into the
device or into the connection terminals for electric conductors. Do not
touch the connection terminals.
Keep the ventilation slits free to ensure good air circulation.
Install the device in the vertical position.
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
2004/108/EC (EMC)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic compati-
bility.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
The device can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55022
You find more information on technical and industry standards here:
“Technical data” on page 32
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take appro-
priate measures.
Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.

10 Installation RED25
Release 01 02/2015
LED or laser components
LED or LASER components according to IEC 60825-1 (2007):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT
FCC note:
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the require-
ments of a class A digital device in line with part 15 of the FCC regula-
tions.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate these
frequencies. If it is not installed and used in accordance with this oper-
ating manual, it can cause radio transmission interference. The use of this
device in a residential area can also cause interference, and in this case
the user is obliged to cover the costs of removing the interference.
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.