Belden grass valley SIRIUS 800 Series User guide

Operating System Upgrade Manual
Windows XP to Windows Embedded Standard 7(WES7)
Issue 1 Revision 3
2019 March 15
SIRIUS 800 ROUTER DOOR PC
FOR USE WITH SIRIUS 830, 840 AND 850 ROUTERS

ii
Notices
FCC Compliance
In order to comply with FCC/CFR47: Part 15 regulations, it is necessary to use Mini HDMI to
HDMI high-quality triple-screened cable assemblies with integrated ferrite suppression at both
ends.
Patent Information
This product may be protected by one or more patents.
For further information, please visit: www.grassvalley.com/patents/
Copyright and Trademark Notice
Copyright © 2019, Grass Valley Canada. All rights reserved.
Belden, Belden Sending All The Right Signals, and the Belden logo are trademarks or registered
trademarks of Belden Inc. or its affiliated companies in the United States and other
jurisdictions. Grass Valley and Sirius 800 Router are trademarks or registered trademarks of
Grass Valley Canada. Belden Inc., Grass Valley Canada, and other parties may also have
trademark rights in other terms used herein.
Terms and Conditions
Please read the following terms and conditions carefully. By using Sirius 800 Router
documentation, you agree to the following terms and conditions.
Grass Valley hereby grants permission and license to owners of Sirius 800 Router to use their
product manuals for their own internal business use. Manuals for Grass Valley products may not
be reproduced or transmitted in any form or by any means, electronic or mechanical, including
photocopying and recording, for any purpose unless specifically authorized in writing by Grass
Valley.
A Grass Valley manual may have been revised to reflect changes made to the product during its
manufacturing life. Thus, different versions of a manual may exist for any given product. Care
should be taken to ensure that one obtains the proper manual version for a specific product
serial number.
Information in this document is subject to change without notice and does not represent a
commitment on the part of Grass Valley.
Warranty information is available from the Legal Terms and Conditions section of Grass Valley’s
website (www.grassvalley.com).
Title Sirius 800 Router Door PC Operating System Upgrade Manual
Part Number Issue 1 Revision 3
Revision 2019 March 15, 14:09

www.grassvalley.com
Contents
1. About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Contact Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Copyright and Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. Warnings and Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.1 Explanation of Safety Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3 Lithium Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.4 Safety Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Pre-upgrade Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1 Before Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.2 Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.3 Pre-upgrade Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4. Back-up XP Door PC Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1 Connecting a USB Hub, Keyboard and Mouse. . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2 Workbench and Database Back-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.3 Door PC settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5. Windows Embedded Standard 7 (WES 7) Installation . . . . . . . . . . . . . . . . . . . . . 13
6. Configure the Windows 7 Door PC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.1 Flipping the Display Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.2 Calibrate the Touchscreen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.3 Configure the Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.4 Turn off visual effects. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.5 Switch off the Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.6 Switch off the Auto-updates (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.7 Enable Remote Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.8 Set the IP Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.9 Set Password to Never Expire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.10 Set the PC Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7. Install and Configure Workbench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.1 Installing Workbench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.2 Restoring the Database(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.3 Completing the Upgrade and Configuring Workbench . . . . . . . . . . . . . . . . . . . . 26
Contact Us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

www.grassvalley.com
1. About this Manual
This Door PC Operating System Upgrade manual describes the procedure to upgrade the
Door PC from Windows XP to Windows Embedded Standard 7 (WES 7). Refer to the
Sirius 800 User Manual for Door PC operational details and the Workbench manual for
Workbench operation.
If you have any questions regarding the upgrade, please contact Customer Support, see
section 1.1 for contact details.
1.1 Contact Details
Customer Support
For details of our Regional Customer Support Offices please visit the web site link below:
https://www.grassvalley.com/contact/support/
Customers with a support contract should call their personalized number, which can be found
in their contract, and be ready to provide their contract number and details.
1.2 Copyright and Disclaimer
Copyright protection claimed includes all forms and matters of copyrightable material and
information now allowed by statutory or judicial law or hereinafter granted, including without
limitation, material generated from the software programs which are displayed on the screen
such as icons, screen display looks etc.
Information in this manual and software are subject to change without notice and does not
represent a commitment on the part of Grass Valley. The software described in this manual is
furnished under a license agreement and can not be reproduced or copied in any manner
without prior agreement with Grass Valley or their authorized agents.
Reproduction or disassembly of embedded computer programs or algorithms prohibited.
No part of this publication can be transmitted or reproduced in any form or by any means,
electronic or mechanical, including photocopy, recording or any information storage and
retrieval system, without permission being granted, in writing, by the publishers or their
authorized agents.
Grass Valley operates a policy of continuous improvement and development. Grass Valley
reserves the right to make changes and improvements to any of the products described in this
document without prior notice.

Door PC Operating System Upgrade Manual Warnings and Precautions
Issue 1 Rev 3 Page 2 © 2019 Grass Valley
2. Warnings and Precautions
Erklärung der Sicherheitssymbole
Dieses Symbol weist den Benutzer auf wichtige Informationen
hin, die in der begleitenden Dokumentation enthalten sind.
Dieses Symbol zeigt an, dass gefährliche Spannung vorhanden ist.
Es befinden sich keine vom Benutzer zu wartenden Teile im Geräteinneren.
Dieses Gerät sollte nur von geschultem Personal gewartet werden
·Um das Risiko eines Elektroschocks zu reduzieren, setzen Sie das
Gerät weder Regen noch Feuchtigkeit aus.
·Stellen Sie imm er sicher, dass das Gerät ordnungsgemäß geerdet
und verkabelt ist.
·Dieses Equipment muss an eine Netzsteckdose mit Schutzleiter
angeschlossen werden und einen zuverlässig identifizierbaren Nullleiter haben.
·Die Netzsteckdose sollte nahe beim Gerät und einfach zugänglich sein.
Sicherheits-Warnhinweise
D
!
Die angeführten Service-/Reparatur-Anweisungen sind
ausschließlich von qualifiziertem Service-Personal
auszuführen. Um das Risiko eines lektroschocks zu
reduzieren, führen Sie ausschließlich die im
Benutzerhandbuch eschriebenen Anweisungen aus,
es sei denn, Sie haben die entsprechende Qualifikation.
Wenden Sie sich in allen Service-Fragen an qualifiziertes Personal.
!ACHTUNG
Gefahr von Elektroschocks.
A bde ck unge n nic ht e ntferne n
Ke ine vom Be nutze r z u w arte nde T eile
Wenden Sie sich ausschließlich
an qualifiziertes Personal
Explicación de los Símbolos de Seguridad
Éste símbolo refiere al usuario información importante contenida
en la literatura incluida. Referirse al manual.
Éste símbolo indica que voltajes peligrosos están presentes en el interior.
No hay elementos accesibles al usuario dentro.
Esta unidad sólo debería ser tratada por personal cualificado.
Las instrucciones de servicio cuando sean dadas, son
sólo para uso de personal cualificado. Para reducir el
riesgo de choque eléctrico no llevar a cabo ninguna
operación de servicio aparte de las contenidas en las
instrucciones de operación, a menos que se esté
cualificado para realizarlas.
Referir todo el trabajo de servicio a personal cualificado.
·
Para reducir el riesgo de choque eléctrico, no exponer este equipo
a la lluvia o humedad.
· Siempre asegurarse de que la unidad está propiamente conectada a
tierra y que las conexiones de alimentación están hechas correctamente.
· Este equipo debe ser alimentado desde un sistema de alimentación
con conexión a TIERRA y teniendo una conexión neutra fácilmente
identificable.
· La toma de alimentación para la unidad debe ser cercana y fácilmente
accesible.
E
S
P
!
Advertencias de Seguridad
RIESGO DE CHOQUE ELECTRICO
NO QUITAR LAS PROTECCIONNES
ELEMENTOS NO ACCESIBLES AL
USUARIO.
SERVICIO SOLAMENTE A PERSONAL
CUALIFICADO
Simboli di sicurezza:
Questo simbolo indica l'informazione importante contenuta nei
manuali appartenenti all'apparecchiatura. Consultare il manuale.
Questo simbolo indica che all'interno dell'apparato sono presenti
tensioni pericolose. Non cercare di smontare l'unità.
Per qualsiasi tipo di intervento rivolgersi al personale qualificato.
Le istruzioni relative alla manutenzione sono ad uso
esclusivo del personale qualificato. E' proibito all'utente
eseguire qualsiasi operazione non esplicitamente
consentita nelle istruzioni. Per qualsiasi informazione
rivolgersi al personale qualificato.
·
Per prevenire il pericolo di scosse elettriche è necessario non esporre
mai l'apparecchiatura alla pioggia o a qualsiasi tipo di umidità.
· Assicurarsi sempre, che l'unità sia propriamente messa a terra e che
le connessioni elettriche siano eseguite correttamente.
· Questo dispositivo deve essere collegato ad un impianto elettrico
dotato di un sistema di messa a terra efficace.
· La presa di corrente deve essere vicina all'apparecchio
e facilmente accessibile.
I
!
Attenzione:
!
ATTENZIONE
RISCHIO DI SHOCK ELETTRICO
NON CERCARE DI SMONTARE
L'UNITA PER QUALSIASI TIPO DI
INTERVENTO RIVOLGERSI AL
PERSONALE QUALIFICATO
Forklaring på sikkerhedssymboler
Dette symbol gør brugeren opmærksom på vigtig information
i den medfølgende manual.
Dette symbol indikerer farlig spænding inden i apparatet. Ingen bruger
servicerbare dele i apparatet på brugerniveau.
Dette apparat må kun serviceres af faglærte personer..
Serviceinstruktioner er kun til brug for faglærte
servicefolk. For at reducere risikoen for elektrisk
stød må bruger kun udføre anvisninger i
betjeningsmanualen.
Al service skal udføres af faglærte personer.
·
For at reducere risikoen for elektrisk stød må apparatet ikke
udsættes for regn eller fugt.
· Sørg altid for at apparatet er korrekt tilsluttet og jordet.
· Dette apparat skal forbindes til en nettilslutning, der yder
BESKYTTENDE JORD og 0 forbindelse skal være tydeligt markeret.
· Stikkontakten, som forsyner apparatet, skal være tæt på apparatet
og let tilgængelig
.
D
K
!
!
Sikkerhedsadvarsler
!
FORSIGTIG
RISIKO FOR ELEKTRISK STØD
DÆKPLADERMÅIKKEFJERNES
INGEN BRUGER SERVICERBARE
DELE SERVICE MÅ KUN UDFØRES
AF FAGLÆRTE PERSONER

Door PC Operating System Upgrade Manual Warnings and Precautions
Issue 1 Rev 3 Page 3 © 2019 Grass Valley
Förklaring av Säkerhetssymboler
Denna symbol hänvisar användaren till viktig information som
återfinns i litteraturen som medföljer. Se manualen.
Denna symbol indikerar att livsfarlig spänning finns på insidan.
Det finns inga servicevänliga delar inne i apparaten.
Denna apparat få endast repareras av utbildad personal.
Serviceinstruktioner som anges avser endast kvalificerad
och utbildad servicepersonal. För att minska risken för
elektrisk stöt, utför ingen annan service än den som
återfinns i medföljande driftinstruktionerna, om du ej är
behörig. Överlåt all service till kvalificerad personal.
·
För att reducera risken för elektrisk stöt, utsätt inte apparaten för
regn eller fukt.
· Se alltid till att apparaten är ordentligt jordad samt att strömtillförseln
är korrekt utförd.
· Denna apparat måste bli försörjd från ett strömsystem som är försedd
med jordadanslutning samt ha en neutral anslutning som lätt identifierbar.
· Vägguttaget som strömförsörjer apparaten bör finnas i närheten samt
vara lätttillgänglig.
S
!
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVERS
NO USER SERVICEABLE PARTS
REFER SERVICING TO QUALIFIED
PERSONNEL ONLY
!
Säkerhetsvarningar
Turvamerkkien selitys
Tämä merkki tarkoittaa, että laitteen mukana toimitettu kirjallinen
materiaali sisältää tärkeitä tietoja. Lue käyttöohje.
Tämä merkki ilmoittaa, että laitteen sisällä on vaarallisen voimakas jännite.
Sisäpuolella ei ole mitään osia, joita käyttäjä voisi itse huoltaa.
Huollon saa suorittaa vain alan ammattilainen.
Huolto-ohjeet on tarkoitettu ainoastaan alan
ammattilaisille. Älä suorita laitteelle muita
toimenpiteitä, kuin mitä käyttöohjeissa on
neuvottu, ellet ole asiantuntija. Voit saada sähköiskun.
Jätä kaikki huoltotoimet ammattilaiselle.
·
Sähköiskujen välttämiseksi suojaa laite sateelta ja kosteudelta.
· Varmistu, että laite on asianmukaisesti maadoitettu ja että
sähkökytkennät on tehty oikein.
· Laitteelle tehoa syöttävässä järjestelmässä tulee olla
SUOJAMAALIITÄNTÄ ja nollaliitännän on oltava luotettavasti
tunnistettavissa.
· Sähköpistorasian tulee olla laitteen lähellä ja helposti tavoitettavissa.
F
I
!
Turvaohjeita
!
SÄHKÖISKUN VAARA ÄLÄ AVAA
LAITTEEN KANSIA EI SISÄLLÄ
KÄYTTÄJÄLLE HUOLLETTAVIA
OSIA HUOLTO AINOASTAAN
AMMATTILAISEN SUORITTAMANA
VAROITUS
Símbolos de Segurança
O símbolo triangular adverte para a necessidade de consultar o
manual antes de utilizar o equipamento ou efectuar qualquer ajuste.
Este símbolo indica a presença de voltagens perigosas no interior
do equipamento. As peças ou partes existentes no interior do equipamento
não necessitam de intervenção, manutenção ou manuseamento por parte
do utilizador. Reparações ou outras intervenções devem ser efectuadas
apenas por técnicos devidamente habilitados.
As instruções de manutenção fornecidas são para
utilização de técnicos qualificados. Para reduzir o
risco de choque eléctrico, não devem ser realizadas
intervenções no equipamento não especificadas no
manual de instalações a menos que seja efectuadas
por técnicos habilitados.
·
Para reduzir o risco de choque eléctrico, não expor este equipamento
à chuva ou humidade.
· Assegurar que a unidade está sempre devidamente ligada à terra e
que as ligações à alimentação estão correctas.
· O sistema de alimentação do equipamento deve, por razões de
segurança, possuir ligação a terra de protecção e ligação ao
NEUTRO devidamente identificada.
· A tomada de energia à qual a unidade está ligada deve situar-se na
sua proximidade e facilmente acessível.
P
!
Avisos de Segurança

Door PC Operating System Upgrade Manual Warnings and Precautions
Issue 1 Rev 3 Page 4 © 2019 Grass Valley
2.1 Explanation of Safety Symbols
2.2 Safety Warnings
Servicing instructions, where given, are for use by qualified personnel only. To reduce the risk
of electric shock, do not perform any actions on this equipment other than contained in the
operating instructions, unless you are qualified to do so. Refer all servicing to qualified
personnel.
Always ensure that the unit is properly earthed and power connections correctly made.
This equipment must be supplied from a power system providing a PROTECTIVE EARTH
connection and having a neutral connection which can be reliably identified.
The power circuit breakers or switches supplying power to the unit should be close to the unit
and easily accessible.
2.3 Lithium Batteries
The Door PC contains a Lithium battery to provide non-volatile memory.
This symbol refers the user to important information contained in the accompanying
literature.
This symbol indicates that hazardous voltages are present inside. No user serviceable
parts inside. This system should only be serviced by trained personnel.
To reduce the risk of electric shock, do not expose this appliance to rain or moisture.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVERS
NO USER SERVICABLE PARTS
REFER SERVICING TO QUALIFIED
PERSONNEL ONLY
Note:
• Used batteries should be disposed of in accordance with the manufacturers
instruction and any specific local legislation regarding the recycling of waste
batteries and accumulators
• Ensure that the same make and model of battery is used if replacement is required
(a manufacturer recommended equivalent can be used if the original type is not
available)
This equipment contains a lithium battery
There is a danger of explosion if this is replaced incorrectly
Replace only with the same or equivalent type.
Dispose of used batteries according to the manufacturers instructions.
Batteries should only be replaced by trained service technicians
CAUTION

Door PC Operating System Upgrade Manual Warnings and Precautions
Issue 1 Rev 3 Page 5 © 2019 Grass Valley
2.4 Safety Standards
This equipment complies with the following standards:
EN60950-1 2006
Safety of information Technology Equipment Including Electrical Business Equipment.
UL1419 (3rd Edition) - UL File E193966
Standard for Safety - Professional Video and Audio equipment
EMC Standards
This unit conforms to the following standards:
EN55103-1:1996 (Environment E4)
Electromagnetic Compatibility, Product family standard for audio, video, audio-visual and
entertainment lighting control apparatus for professional use. Part 1. Emission
EN55103-2:1996 (Environment E2)
Electromagnetic Compatibility, Product family standard for audio, video, audio-visual and
entertainment lighting control apparatus for professional use. Part 2. Immunity
Federal Communications Commission Rules, 47 CFR, Part 15, Subpart B (Class A)
EMC Performance of Cables and Connectors
Grass Valley products are designed to meet or exceed the requirements of the appropriate
European EMC standards. In order to achieve this performance in real installations it is
essential to use cables and connectors with good EMC characteristics.
All signal connections (including remote control connections) shall be made with screened
cables terminated in connectors having a metal shell. The cable screen shall have a
large-area contact with the metal shell.
COAXIAL CABLES
Coaxial cables connections (particularly serial digital video connections) shall be made with
high-quality double-screened coaxial cables such as Belden 1694A or Belden 1505A.
D-TYPE CONNECTORS
D-type connectors shall have metal shells making good RF contact with the cable screen.
Connectors having “dimples” which improve the contact between the plug and socket shells,
are recommended.

www.grassvalley.com
3. Pre-upgrade Tasks
This manual describes the following processes:
• Pre-upgrade information, equipment required and checklist - this section.
• Back-up the current Windows XP Door PC settings - see section 4.
• Install Windows Embedded Standard 7 (WES 7) - see section 5.
• Configure Windows 7 Door PC settings - see section 6.
• Re-install and configure Workbench - see section 7.
3.1 Before Starting
• This manual assumes you have a good working knowledge of Windows operating
systems and the Workbench system.
• Read through the complete upgrade procedure and make sure you understand all of
the steps before starting work on the Door PC.
• It is important that all of the information in the pre-upgrade checklist is noted down
and easily accessible before starting the upgrade, see section 3.3.
• Check the contents of the FGAEY S800-W7UG upgrade kit:
• WES 7 Runtime installation USB memory stick
• WES 7 license label
• Workbench installation USB memory stick
• A printed copy of this upgrade manual
3.2 Equipment Required
To perform the upgrade from Windows XP to Windows Embedded Standard 7 (WES 7), the
following equipment is required:
• USB peripherals
• Keyboard
• Mouse
• USB hub (not required if Keyboard has an integrated hub)
• USB extension cable (for easier USB port access)
• WES 7 Runtime installation USB memory stick (Part of this Kit FGAEY S800-W7UG)
• Workbench installation USB memory stick (Part of this Kit FGAEY S800-W7UG).
Important:
Failure to complete the checklist correctly may result in a failed upgrade.

Door PC Operating System Upgrade Manual Pre-upgrade Tasks
Issue 1 Rev 3 Page 7 © 2019 Grass Valley
• Spare USB memory stick for back-up purposes
(alternatively the Workbench USB memory stick can be used)
3.3 Pre-upgrade Checklist
It is important that all of the information in the pre-upgrade checklist is noted down and easily
accessible before starting the upgrade. This information will be required for the upgrade as
the entire door PC hard drive will be formatted as part of the upgrade process.
Important:
Failure to complete the checklist correctly may result in a failed upgrade.
Pre-Upgrade Checklist
Details required Write details in this column
Router Controller A Details (see section 4.2 for details)
Controller Name
Controller IP Address
Controller Software Version
Router Controller B Details (see section 4.2 for details, if fitted)
Controller Name
Controller IP Address
Controller Software Version
Door PC Workbench Details (see section 4.3 for details):
Workbench Version
Backup Database Filename(s)
Door PC Details (see section 4.3 for details):
Computer Description
Computer Name
Door PC IP Address Details (see section 4.3 for details):
IP Address
Subnet Mask
Default Gateway
Preferred DNS
Alternate DNS
Table 1. Pre-upgrade Checklist

www.grassvalley.com
4. Back-up XP Door PC Settings
4.1 Connecting a USB Hub, Keyboard and Mouse
The upgrade process requires the connection of three USB devices at the same time (mouse,
keyboard and the USB memory stick). As the Door PC only has two USB ports a USB hub
must be connected to carry out the upgrade.
1. Connect your USB hub to one of the Door PC USB sockets shown in Fig 2.
2. Connect a USB keyboard and mouse to the USB hub and they will be recognized by
the Door PC and the drivers will be installed automatically.
4.2 Workbench and Database Back-up
1. Close down the LiveRunner Screen by clicking on the Exit button but do not
shutdown the Door PC.
2. Click on the Close button when prompted.
Fig 1. Door PC Ports Viewed From Below
USB Ports
Fig 2. Closing Live Runner on the Door PC
1. Click on the Exit button to
start closing LiveRunner
2. Click on the Close button

Door PC Operating System Upgrade Manual Back-up XP Door PC Settings
Issue 1 Rev 3 Page 9 © 2019 Grass Valley
3. Open up Workbench from the shortcut, or Start menu if no shortcut available. Take a
note of the Controller Names and IP Settings in the frame and write them in the
checklist in section 3.3.
4. Close down Workbench.
5. Insert the Back-up USB memory stick and create a Back-up folder for the Door PC.
6. Open up SQL Server 2008 R2 Server Management Studio, from the Start menu.
7. Click on the Connect button to log in, and then browse the Database objects in the
Object Explorer.
8. Back-up the Database(s), primarily this will be just the Workbench one, but there
could be others that also need backing up.
a Highlight the database to back up
b Right click to bring up context menu
cSelectTasks
d Choose BackUp ...
Fig 3. Log in to SQL Server
Click Connect to log in.

Door PC Operating System Upgrade Manual Back-up XP Door PC Settings
Issue 1 Rev 3 Page 10 © 2019 Grass Valley
e Highlight and Remove any old backup paths in the Destination list box
f Then click Add... and browse to the location on the USB stick you are putting the
Database Backups. Type in the name of the back-up file, not forgetting to include
the '.bak' file extension (this isn't automatically added for you)
g Under the Select a page->Options ensure you have the Overwrite all existing
backup set.
Fig 4. SQL Server BackUp
Fig 5. Remove any Old Backups
Choose BackUp...
Remove any old Backups

Door PC Operating System Upgrade Manual Back-up XP Door PC Settings
Issue 1 Rev 3 Page 11 © 2019 Grass Valley
h Click OK, start the back up process and add the backup filename to the checklist
in section 3.3.
i Repeat this process for all the Databases being backed up.
Fig 6. SQL BackUp Options
Ensure Overwrite all existing backup sets
is selected

Door PC Operating System Upgrade Manual Back-up XP Door PC Settings
Issue 1 Rev 3 Page 12 © 2019 Grass Valley
4.3 Door PC settings
1. Click Start, then right-click on My Computer and select Properties. Under the
Computer Name tab take a note of the Computer Description and the Full
computer name and add them to the checklist in section 3.3.
2. Close the dialog.
3. Click Start, open Control Panel, open Network Connections and then Local Area
Connection properties of the connected LAN. Select Internet Protocol (TCP/IP) from
the list, click the Properties button. Write down all the IP address settings for the PC
in the check list in section 3.3.
4. Copy the Workbench shortcuts (LiveRunner and Workbench) onto the Backup
USB drive if using a Database server, or different database names other than the
default “Workbench”.
5. Open the Shortcut properties, and take a note if Workbench is running from a local
Database or a remote network Database.
Fig 7. Door PC Computer Properties
Fig 8. Door PC IP Address Details
Important:
WARNING: The process of installing the new Windows Embedded Standard 7 onto the
Door PC will format the entire HDD drive, so back-up any other important data before
proceeding to the next step. This data could include but is not limited to:
• RollCall and/or older versions of Workbench
• Any additional applications in regular use
Add the Door PC
Computer Description and the
Full computer name
to the checklist, see section 3.3
Add the Door PC
IP Address details
to the checklist,
see section 3.3

www.grassvalley.com
5. Windows Embedded Standard 7 (WES 7) Installation
1. Safely remove the USB drive you used to backup the database(s) and insert the Door
PC WES 7 USB memory stick.
2. Re-start the PC using Windows Start menu
3. Enter the BIOS by pressing the [Delete] key (not the Backspace key) on the keyboard
to enter Set up.
4. Using the arrow keys, scroll to Advanced BIOS features and press the [Enter] key.
5. Scroll to Hard Disk Boot Priority and press the [Enter] key.
6. Follow the screen instruction to set the Boot order so that the USB drive is number 1
in the list of drives.
7. Press the [F10] key followed by yand [Enter] to Save and Exit.
8. The PC will now reboot, and run the WES 7 installation USB.
9. Wait whilst the Windows files are extracted and the machine boots up. The BVM logo
will be displayed when the boot is complete (this takes approximately 5 minutes).
10. Type yfollowed by the [Enter] key when asked at the DOS prompt about disk
partitions.
11. WES 7 will now install. This will take about 5 minutes.
12. When asked to reboot the machine to complete the installation, type yfollowed by the
[Enter] key and the Door PC will power down.
13. Remove the WES 7 USB stick and then power the PC back on using the power button
on the rear of the door.
14. After rebooting, WES 7 will continue to install extracting files and changing system
settings. This will take some time and Door PC will reboot a number of times
automatically (this will take approximately 5 minutes).
15. Installation is complete after the final reboot when the dialog box is displayed that
says the machine will restart in less than 30 seconds.
16. The Door PC will now reboot with the SAM/Grass Valley wallpaper installed.
17. Stick the Microsoft WES 7 License sticker on the rear of the Door PC.
Important:
WARNING: This Installation will format the Hard Drive; do not proceed unless you are
certain that everything has been backed up.
Note:
From this point the display will be inverted. This will be corrected in section 6.
Important:
The Microsoft WES 7 License sticker must be mounted on the rear of the Door PC for the
installation to be legally licensed.

www.grassvalley.com
6. Configure the Windows 7 Door PC
6.1 Flipping the Display Orientation
The Door PC screen mounted in the door is inverted, so in order to use it sensibly the display
needs to be flipped.
1. Right-click on the desktop and select Screen Resolution from the right click menu.
2. From the Orientation drop down box, choose Landscape (flipped), see Fig 9.
3. Click the OK button to change the display orientation.
4. When the keep or revert dialog is displayed, click on the Keep Changes button.
6.2 Calibrate the Touchscreen.
The Touchscreen driver now needs calibrating
1. Click the Start button.
2. Select All Programs and then select the DMC Touch screen panel configuration
option from the DMC program group.
3. With the Calibration button highlighted on the left hand side, click the Calibrate
button on the right hand side.
4. Using your finger to press the center of each of the four crosses as they appear in
each corner of the screen.
Fig 9. Flipping the Door PC Screen
Select
Landscape (Flipped)
from the drop down
list to rotate the
display to the correct
orientation

Door PC Operating System Upgrade Manual Configure the Windows 7 Door PC
Issue 1 Rev 3 Page 15 © 2019 Grass Valley
5. Press the OK button when it appears.
6. Close the calibration screen.
6.3 Configure the Screen Saver
1. Insert the WES 7 USB stick.
2. Open the Snell Screen Saver folder.
3. Run install_flash_player_13_active_x.exe to install Adobe Flash player.
4. Accept the Flash player terms and conditions and install with all default settings.
5. When the installation is complete click on the Done button.
6. Run Snell3dscreensaver New.exe and click on the Continue button to install the
screen saver.
7. Click the Finish button when prompted.
8. Safely remove the WES 7 USB stick.
9. Right-click on the desktop and select Personalize from the menu.
10. Click on the Screen Saver icon in the bottom right of the personalization screen as
shown in Fig 11.
11. From the Screen Saver Settings dialog set the Wait time to 20 minutes.
12. Click on the OK button to save the settings.
Fig 10. Right-Click Menu
Select Personalize
from the menu

Door PC Operating System Upgrade Manual Configure the Windows 7 Door PC
Issue 1 Rev 3 Page 16 © 2019 Grass Valley
13. Close the Personalization screen.
6.4 Turn off visual effects
To adjust all visual effects for best performance:
1. Click on the Start button and open the Control Panel.
2. In the control panel search box type performance information and click on
Performance Information and Tools in the results list.
3. Click on the Adjust visual effects option on the top left of the screen.
4. Click on the Visual Effects tab and select the Adjust for best performance radio
button as shown in Fig 12.
5. Click on the OK button and close the other windows.
Fig 11. Configure Screen Saver
10. Click on the Screen Saver icon
11. Set the Wait time
to 20 minutes
12. Click on the OK button to save the settings
Fig 12. Visual Effects Tab
Select the
Adjust for best performance
radio button

Door PC Operating System Upgrade Manual Configure the Windows 7 Door PC
Issue 1 Rev 3 Page 17 © 2019 Grass Valley
6.5 Switch off the Firewall
1. Click on the Start button and open the Control Panel.
2. In the control panel search box type windows firewall and click on Windows
Firewall in the results list.
3. Select the Turn Windows Firewall on or off option from the top left of the Windows
Firewall screen.
4. Select both of the Turn off Windows Firewall (not recommended) radio buttons.
5. Click on the OK button to accept the changes.
6.6 Switch off the Auto-updates (Optional)
1. Type windows update in the control panel search box and click on Windows Update
in the results list.
2. Select the Change Settings option from the top left of the Windows Update screen.
3. Select the Never check for updates (not recommended) option from the Important
Updates drop-down box, see Fig 14.
Fig 13. Windows Firewall Screen
Select both of the Turn off Windows Firewall (not recommended) radio
buttons as shown