Belden HIRSCHMANN RSPE 30 User manual

Installation RSPE 30/32/35/37
Release 08 08/2014
Technical support
https://hirschmann-support.belden.eu.com
User Manual
Installation
Industrial Ethernet Rail Switch Power Enhanced
RSPE 30/32/35/37

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2014 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD/DVD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
Installation RSPE 30/32/35/37 040 045-001-08-0814 - 29.07.2014

Installation RSPE 30/32/35/37
Release 08 08/2014 3
Contents
Safety instructions 5
About this manual 11
Key 11
1 Description 12
1.1 General description 12
1.2 Device name and product code 13
1.3 Combination options 17
1.4 Device views 18
1.4.1 Front view 18
1.4.2 Rear view 19
1.5 Power supply 20
1.5.1 Working voltage characteristic value K9 20
1.5.2 Working voltage with the characteristic value KK 20
1.5.3 Working voltage characteristic value CC 20
1.5.4 Working voltage with the characteristic value PP 20
1.6 Ethernet ports 21
1.6.1 Gigabit combo port 22
1.6.2 10/100 Mbit/s twisted pair port 23
1.6.3 100 Mbit/s F/O port (optional) 24
1.6.4 Support of PoE and PoE+ 25
1.7 Display elements 26
1.7.1 Device state 26
1.7.2 Media module status 27
1.7.3 Port state 28
1.8 Management interfaces 30
1.8.1 V.24 interface (external management) 30
1.8.2 SD card interface 30
1.8.3 USB interface 31
1.9 Signal contact 31
2 Installation 32
2.1 Unpacking and checking the content of the package 32
2.2 Installing the SD card (optional) 32
2.3 Mounting a dummy panel or a media module 33
2.3.1 Mounting a dummy panel 33
2.3.2 Mounting a media module 33

4Installation RSPE 30/32/35/37
Release 08 08/2014
2.4 Installing and grounding the device 34
2.4.1 Installing the device onto the DIN rail 34
2.4.2 Grounding the device 35
2.5 Installing an SFP transceiver (optional) 36
2.6 Connecting the terminal blocks 36
2.6.1 Working voltage characteristic value K9 37
2.6.2 Working voltage with the characteristic value KK 38
2.6.3 Working voltage characteristic value CC 39
2.6.4 Working voltage with the characteristic value PP 40
2.6.5 Signal contact 41
2.7 Operating the device 42
2.8 Connecting data cables 42
2.9 Filling out the inscription label 42
3 Making basic settings 43
4 Upgrading Software 44
5 Monitoring the ambient air temperature 45
6 Maintenance and service 46
7Disassembly 47
7.1 Removing the device 47
7.2 Removing an SFP transceiver (optional) 48
7.3 Removing a media module (optional) 48
8 Technical data 49
A Further Support 61

Installation RSPE 30/32/35/37
Release 08 08/2014 5
Safety instructions
General safety instructions
You operate this device with electricity. The proper and safe operation of
this device depends on proper handling during transportation, proper
storage and assembly, and conscientious operation and maintenance
procedures. Improper use of this device is associated with the risk of
personal injury or property damage.
Read this documentation as well as the safety instructions and
warnings before connecting any cables.
Never start operation with damaged components.
The device does not contain any service components. If the device is
not functioning correctly, or if it is damaged, turn off the power supply
and return the device to Hirschmann for inspection.
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
Certified usage
Use the device solely for the application cases described in the
Hirschmann product information, including this manual.
Operate the device solely according to the technical specifications.
See “Technical data” on page 49.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

6Installation RSPE 30/32/35/37
Release 08 08/2014
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
Grounding the device
Grounding the device is by means of a separate ground connection on the
device.
Ground the device before connecting any other cables.
Disconnect the grounding only after disconnecting all other cables.
The overall shield of a connected shielded twisted pair cable is connected
to the ground connector on the front panel as a conductor.
Working voltage
The working voltage is connected to the chassis through protective
elements exclusively.
Connect only a working voltage that corresponds to the type plate of
your device.
Only for device variants featuring working voltage with the
characteristic value K9 or KK:
See “Device name and product code” on page 13.
Every time you connect the electrical conductors, make sure that the
following requirements are met:
The power supply conforms to overvoltage category I or II.
The power supply has an easily accessible disconnecting device
(e.g., a switch or a plug). This disconnecting device is clearly
identified. So in the case of an emergency, it is clear which
disconnecting device belongs to which power supply cable.
The electrical wires are voltage-free.
Supply with DC voltage:
A fuse suitable for DC voltage is located in the plus conductor of the
power supply.
The minus conductor is on ground potential. Otherwise, a fuse is
also located in the minus conductor.
Regarding the properties of this fuse: See “General technical data”
on page 49.
Supply with AC voltage:
A fuse is located in the outer conductor of the power supply.
The neutral conductor is on ground potential. Otherwise, a fuse is
also located in the neutral conductor.
Regarding the properties of this fuse: See “General technical data”
on page 49.
Supply with AC voltage:
The wire diameter of the power supply cable is at least 0.75 mm²
(North America: AWG18) on the working voltage input.

Installation RSPE 30/32/35/37
Release 08 08/2014 7
Supply with DC voltage:
The wire diameter of the power supply cable is at least 1 mm²
(North America: AWG16) on the working voltage input.
The cross-section of the protective conductor is the same size as
or bigger than the cross-section of the power supply cables.
The power supply cables used are permitted for the temperature
range required by the application case.
Relevant for North America:
The power cords are suitable for ambient air temperatures of at
least 167 °F (75 °C). The power cord wires are made of copper.
Start connecting the electrical wires only if all the above safety
requirements are fulfilled.
Only for device variants featuring working voltage with the
characteristic value C or PP:
See “Device name and product code” on page 13.
Every time you connect the electrical conductors, make sure that the
following requirements are met:
Solely for device variants with the characteristic value CC for the
working voltage:
The power supply is Class 2 compliant.
The power supply conforms to overvoltage category I or II.
The working voltage inputs are designed for operation with safety
extra-low voltage. Connect only SELV circuits with voltage
restrictions in line with IEC/EN 60950-1 to the working voltage
connections.
The power supply has an easily accessible disconnecting device
(e.g., a switch or a plug). This disconnecting device is clearly
identified. So in the case of an emergency, it is clear which
disconnecting device belongs to which power supply cable.
The electrical wires are voltage-free.
A fuse suitable for DC voltage is located in the plus conductor of the
power supply.
The minus conductor is on ground potential. Otherwise, a fuse is
also located in the minus conductor.
Regarding the properties of this fuse: See “General technical data”
on page 49.
The wire diameter of the power supply cable is at least 1 mm²
(North America: AWG16) on the working voltage input.
The cross-section of the ground conductor is the same size as or
bigger than the cross-section of the power supply cables.

8Installation RSPE 30/32/35/37
Release 08 08/2014
The power supply cables used are permitted for the temperature
range required by the application case.
Relevant for North America:
The power cords are suitable for ambient air temperatures of at
least 167 °F (75 °C). The power cord wires are made of copper.
Start connecting the electrical wires only if all the above safety
requirements are fulfilled.
Internal fuses are triggered solely in the case of a detected error in the
device. In case of damage or malfunction of the device, turn off the
working voltage and return the device to the plant for inspection.
For operating voltage connections with a protective conductor
connection: connect the protective conductor before connecting the
conductors for the operating voltage.
Only switch on the operating voltage for the device when the following
requirements are fulfilled:
The housing is closed
The terminal blocks are wired correctly
The terminal blocks for the operating supply are connected
Signal contact
For the signal contact to be connected, make sure the following
requirements are met:
The device is grounded.
The signal contact connection wires are voltage-free.
The connected voltage is limited by a current limitation device or a
fuse.
Observe the electrical threshold values for the signal contact.
See “General technical data” on page 49.
Start connecting the signal contact solely if all the above requirements are
fulfilled.
Installation site requirements
Install the device in a fire protected enclosure according to
EN 60950-1.
Only for device variants featuring working voltage with the
characteristic value K9 or KK:
See “Device name and product code” on page 13.
Install this device solely in a switch cabinet or in an operating site with
restricted access, to which maintenance staff have exclusive access.

Installation RSPE 30/32/35/37
Release 08 08/2014 9
Housing
Only technicians authorized by the manufacturer are permitted to open
the housing.
Never insert pointed objects (narrow screwdrivers, wires, etc.) into the
device or into the connection terminals for electric conductors. Do not
touch the connection terminals.
Keep the ventilation slits free to ensure good air circulation.
Install the device in the vertical position.
At ambient temperatures > 140 °F (60 °C):
The surfaces of the device housing may become hot. Avoid touching
the device while it is operating.
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
The product can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55022
Reliability: EN 60950-1
You find more information on technical and industry standards here:
“Technical data” on page 49
Device variant Directive
All variants 2004/108/EC (EMC)
Directive of the European Parliament and the council for stan-
dardizing the regulations of member states with regard to elec-
tromagnetic compatibility.
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the
restriction of the use of certain hazardous substances in elec-
trical and electronic equipment.
Only for device variants featur-
ing working voltage with the
characteristic value K9 or KK:
2006/95/EC
Directive of the European Parliament and the council for stan-
dardizing the regulations of member states with regard to elec-
trical equipment to be used within specific voltage ranges.

10 Installation RSPE 30/32/35/37
Release 08 08/2014
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.
Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.
LED or laser components
LED or LASER components according to IEC 60825-1 (2007):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT
Note: You will find additional warning and safety information in the “User
Manual Installation RSPE 30/32/35/37” supplied with every RSPE
30/32/35/37 device.
FCC note:
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate these
frequencies. If it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a residential area can also cause interference, and in this
case the user is obliged to cover the costs of removing the interference.
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.