Wallbeds Australia AB-6a User manual

AB-6a Cupboard & Pull Out Drawer/Table Assembly Instructions
Note: If you have two of the same cabinet each cabinet will have a different cabinet number. Prior
to assembly, separate and group all matching panels panel numbers.
Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the
units have been built, as these will assist with assembly. Most of the stickers are
placed on the “back” or underside of the cabinet and will not be seen once assembled.
End Left
Cupboard Door End Right
Back Bottom Panel
Top Panel
AB-6a Cupboard & Drawer Panels
Pull Out Drawer/Table Bottom
Kick
1
Pull Out Drawer/Table Front
©2019 WallBeds Australia
Adjustable Shelf

AB-6a Cupboard Drawer Hardware Parts
Small Handle Drawer Clip
Pullout Drawer/Table Runners
Handle Screw Door Hinge Door Hinge Clip
Euro Screw Cam Lock Cam Pin
Dome Head Screw 28mm Wood Screw
2
Cam Locks – Insert all Cam Locks into the following panels as described by the cabinet part
located on the cabinet sticker.
Back Bottom Top
Rail
Step 1 – Inserting Hardware
©2019 WallBeds Australia
Adjustable Shelf Pin

Cam Pins Insert all Cam Locks into the following panels as described by the cabinet part located
on the cabinet sticker.
End End Drw Bot Bottom Top
NOTE: In the
Bottom Panel Insert
the cam pins on the
opposite side to the
Cam Lock.
Pull Out Drawer/Table Runners –
Attach the runners before assembling the cabinetry.
To disassemble the runner, turn the drawer runner over to view from the back.
Detach the drawer / table slide from the main sliding runner by pulling the clip as indicated by
the arrow on the clip. Refer image 1 page 9
Line up the three holes in the runner with the pre-drilled holes in the cabinet End Panel. Attach
these runners using the Euro screws.
DO NOT re-attach the slide runner at this point.
Door Hinge Clips –
Attach the Hinge Clips before assembling the cabinetry.
With the arrow indicator on the hinge block facing to the front edge of the panel. Line up the
Hinge Plate with the pre-drilled holes in the End Panel. Fix these by tapping them in gently with
a hammer, then tightening the screws. Refer image 6 page 10
NOTE: In the Top
Panel Insert the cam
pins on the same
side as the Cam
Lock
3
Drawer Clips –
Insert these into the drawer front ensuring the up & down arrows on the drawer clips are facing
the outside edge of the drawer panel. Refer image 10 page 11
Fix these into the drawer front by tapping them in gently with a hammer.
©2019 WallBeds Australia

Step 2 – Cupboard & Pullout Drawer/Table Cabinet Assembly
4
Start the cabinet assembly by using either one of the cabinet End Panels.
Cabinet Back Panel - Place the cabinet back panel onto the side panel. With the cam locks
facing away from the inside match up the cam locks with the cam pins. Tighten the cam
locks and cam pins together by using a Philips head hand screwdriver.
Cabinet Bottom Panel - With the cam locks facing away from the inside of the cabinet attach
the panel to the end panel and back panel. Refer image 7 page 10
Cabinet Top Panel - With the cam locks facing to the inside of the cabinet attach the panel to
the end panel and back panel.
Cabinet Kick/Rail Panel - With the cam locks facing to the back of the cabinet attach the
panel to the end panel.
Place the remaining end panel on top of the previously assembled panels. Ensuring the cam
pins are lined up with the cam locks. Tighten the cam pins to the cam locks.
Note: You may need to lightly tap the cam pins into the cam locks with a rubber mallet.
Ensure you do this where the cam pins are located. Failure to do so may result in damage to
the End Panel.
Pull Out Drawer/Table Slide - Attach the pull out slides to the drawer bottom using the
dome head screws. The holes for these are pre-drilled. Refer image 3 page 9
Cupboard Door - Line up the prongs on the door hinge with the hinge clips. Push the door,
so these clips are all the way in and then push the back of the hinge arm until you hear it
click into position. Refer image 8 page 10
Cupboard Door Hinges –
Place the cup part of the hinge into the cupboard door panel ensuring that the arm of the
hinge is facing out of the door panel. Once in the position close the hinge flap, this
will secure them into place. Refer images 4 and 5 page 9
There are no screws required to attach these hinges.
©2019 WallBeds Australia

AB-6a Top Cabinet Assembly Instructions
Note: If you have two of the same cabinet each cabinet will have a different cabinet number. Prior
to assembly, separate and group all matching panels panel numbers.
Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the
units have been built, as these will assist with assembly. Most of the stickers are
placed on the “back” or underside of the cabinet and will not be seen once assembled.
End Left End Right
Bottom Panel
Top Panel
AB-6a Top Cabinet Panels
Back Panel
5
Adjustable Shelf
Door Panel
©2019 WallBeds Australia

Cam Pins Insert all Cam Locks into the following panels as described by the cabinet part located
on the cabinet sticker.
Cam Lock Cam Pin
Door Hinge Clip
Small Handle Handle Fixing Screw
Door Hinge
Shelf Pin
AB-6a Top Cabinet Hardware Parts
Back Bottom Top
End End
Bottom Top
NOTE: In both the Top and
Bottom Panels Insert the cam
pins on the opposite side to
the Cam Lock.
Step 1 – Inserting Hardware
Cam Locks – Insert all Cam Locks into the following panels as described by the cabinet part
located on the cabinet sticker.
6
28mm Wood Screw
©2019 WallBeds Australia

7
Door Hinge Clips –
Attach the Hinge Plates before assembling the cabinetry.
•Place the Drawer Cabinet unit next to the side of the Alpha Wallbed that it will be attached to.
Ensure the front edge of the drawer is flush with the front edge of the wall bed cabinet.
•Place the upper Cabinet on-top of the drawer cabinet unit. Line up the front edge of the
Bottom Panel with the front edge of the Top Panel of the lower drawer unit. Open the drawer to
achieve this.
•Check that the end panel of the upper cabinet is also flush with the front edge of the wall bed
end panel.
To attach the two units together you will need to use a 5mm
drill bit to pre-drill the 28mm wood screw holes required.
IMPORTANT - Use caution not to go all the way through to the opposing panel of the unit that it
is being attached too. panel of the unit above. Attach units together using the 28mm screws
supplied.
•Remove the Pull Out Drawer / Table. Pre-drill a drill a 5mm hole up through the top panel and
no-more than 5mm into the bottom panel of the unit above. Place one 28mm wood screw
towards the front and then another towards the back of the unit.
•Using an existing shelf pin hole, pre-drill a 5mm hole through the end panel but no-more than
5mm into the End Panel of the wall bed. Fix the cabinet to the side of the wall bed cabinet by
using the 28mm wood screws supplied.
ar
With the arrow indicator on the hinge block facing to the front edge of the panel. Line up the Hinge
Plate with the pre-drilled holes in the End Panel. Fix these by tapping them in gently with
a hammer, then tightening the screws.
Step 2 - Cabinet Assembly
Start the assembly by using either one of the End Panels and fixing it to the Back Panel. Ensure the
cam locks on the Back Panel are not facing what will be the inside of the Bookcase when built.
Back Panel - Place the Back Panel onto the End Panel. Match up the cam locks with the cam pins.
Tighten the cam locks and cam pins together by using a Phillips head hand screwdriver.
Top & Bottom Panels - With the cam locks facing away from the inside, attach the Bottom Panel to
the End Panel and Back Panel. Repeat this process with the Top Panel. Refer image 7 page 10
Place the remaining End Panel on top of the previously assembled panels. Tighten the cam pins to
the cam locks.
Tip: You may need to lightly tap the cam pins into the cam locks with a rubber mallet. Ensure you
do this where the cam pins are. Failure to do so may result in damage to the End Panel.
©2019 WallBeds Australia
Step 3 – Attaching both units together and to the Alpha Wall Bed

Removing Panel Stickers/Labels
To remove once installed, heat up with hair dryer & then to remove any sticky residue
use wax and grease remover or similar.
Avoid using a razor blade as you may damage the cabinetry.
8
Attaching the Door to the Cabinet - Clip the hinge arm into the hinge block previously attached to
the bookcase.
Adjustable Shelf - Insert the shelf pins into the shelf pin holes at the desired height for your shelf.
Attaching the door handle
Place the handle over the pre-drilled holes in the door panel. Insert the handle screws through
the pre-drilled holes in the door panel and tighten using a Phillips head screw driver.
©2019 WallBeds Australia
IMPORTANT SAFETY INFORMATION
All WallBeds Australia Bookcases and Cabinets must be securely attached
to the WallBed before use. Ensure that children DO NOT climb or hang on
any part of the Bookcase or Cabinet.
Failure to do so may result in personal injury.
Step 4 – Fitting the Door Hinges into the Door Panel
Door Hinges –
Place the cup part of the hinge into the cupboard door panel ensuring that the arm of the
hinge is facing out of the door panel. Once in the position close the hinge flap, this will
secure them into place. There are no screws required to attach these hinges.

9
Image 1
Image 2
Image 4Image 5
Image 3
©2019 WallBeds Australia

10
Image 6 Image 7
Image 9
Image 8
©2019 WallBeds Australia

11
Image 10
Image 12
Image 11
NOTE: Image s 11 & 12 is a representation of how to place the Top unit onto Lower unit.
These images may not represent the product purchased.
©2019 WallBeds Australia