BEMIS bioBidet BB-1000 SUPREME User manual

USER MANUAL BB-1000 SUPREME

PRODUCT INFORMATION
Important Safeguards
Overview & Parts
Wireless Remote
GETTING STARTED
Functions & Features
INSTALLATION
Installation Guide
MAINTENANCE
Cleaning Tips
Replacing The Deodorizer
Removing The BB-1000
Draining The Warm Water Tank
Troubleshooting Guide
Specifications
WARRANTY
Warranty
Customer Support
04
09
12
16
22
TABLE OF CONTENTS
Questions?
We’re here to help.
847.458.2334
[email protected]
www.biobidet.com
Technical support and alternate
fittings are available.
Registration and
Installation Resources

4
IMPORTANT SAFEGUARDS
PLEASE OBSERVE THE FOLLOWING PRECAUTIONS
AND INSTRUCTIONS BEFORE INSTALLATION AND USE.
•This product must be connected to a grounded 120V GFCI (Ground Fault
Circuit Interrupt) outlet. Do not connect the power cord if it is damaged or
broken. Do not plug the product into a loose electric outlet.
•It is recommended to operate this product on a separate circuit.
Sharing a circuit could cause the breaker to trip or lights to flicker.
•If it is necessary to use an extension cord, use only a three-prong
extension cord plugged into a proper GFCI outlet. The marked rating
of the extension cord should be equal to or greater than the electrical
rating of the unit (10 amp). Consult a qualified electrician or service
person if you are not sure whether the unit is properly grounded.
•Do not open this product for repair without authorization from the
manufacturer. Only qualified service personnel should service this
product. Do not use accessories not recommended by the manufacturer.
•Connect this product to a potable cold water supply line.
•Close supervision is necessary when this product is used by children,
elderly, or adults with sensitive skin. A low temperature burn may
occur when the skin has been in contact with an object at relatively low
temperature for an extended period of time.
•If using any chemical toilet bowl cleaner, be sure to wipe up any spills that
splash onto the bidet. Do not use benzene or any acid chemical detergent,
as they can cause discoloration. Only neutral detergents are permitted.
•Do not plug in the power cord before connecting the water supply hose.
•Install in an area with adequate ventilation to avoid high levels of
humidity which can damage the electronic components.
•Do not touch the power cord with wet hands or reach for a product
that has fallen into water. Unplug immediately.
•Unplug the bidet seat when cleaning or detaching from the toilet bowl.
Do not plug in until plumbing work has been completed.
•Keep the power cord away from heated surfaces to prevent a fire hazard.
Keep any flammable materials away from this product at all times.

OVERVIEW & PARTS
BB-1000 BB-1000 Parts List
Side Control Panel 3-In-1 Nozzle
Lid
Operation LED Window
Side Control Panel
Deodorizer
Warm Air Dryer
Drain/Quick Release
Nozzle
Seat Sensor
Heated Seat
1. Posterior Wash
2. Feminine Wash
3. Vortex Wash
1. Stop Button
2. Posterior Wash
3. Feminine Wash
PRODUCT INFORMATION
(2) Cone
Packings
Bidet &
Toilet Hoses
Remote
Control
Remote
Control Holder
Wrench
Catch
Plate
(2) AAA
Batteries
Phillips
Screwdriver
(2) Bolt
Guides
(2) Mounting
Bolts
1
1
2
3
3
2
T-Valve
*Rubber washer inside
(2) Nuts 1/2 Conversion Nut
*Rubber washer inside
Deodorizer
*installed in unit
Recommended Installation Tools

98
WIRELESS REMOTE
Stop Button
Rear Wash
Front Wash
Massage
Move
Eco Mode
Vortex Wash
Warm Air Dryer
Adjustable
Water Temperature
Adjustable
Seat Temperature
Adjustable
Nozzle Position
Adjustable
Water Pressure
MOVE
GETTING STARTED
Functions & Features
Sit Down On The Seat
This product includes a built-in seat sensor that must be activated
with skin contact in order to operate bidet functions.
When you sit down on the seat and activate the seat sensor,
the corresponding LED will light up on the main unit and the
deodorizer fan will start.
Stop Button
Stops all operations.
Rear Wash
Press to activate the posterior wash cycle, carefully crafted
with the optimum cleansing angle and spray pattern.
Front Wash
Press to activate the feminine wash cycle, which offers an
alternate accommodating spray pattern.
Vortex Wash
Press to activate a focused wash with higher water pressure.
Warm Air Dryer
Press to activate the warm air dryer. The dryer will automatically
operate for 3 minutes. Press the “High” or “Low” (+ , -) buttons to
adjust the dryer temperature.

MOVE
PRODUCT INFORMATION
Adjustable Water Pressure
Press “High” or “Low” (+, -) to adjust the pressure of the
water spray to your desired comfort level.
Adjustable Nozzle Position
Adjust the nozzle position forward or backward to achieve maximum
cleanliness and comfort by pressing the “Front” or “Rear” (^ , v) buttons.
Adjustable Seat & Water Temperature
Adjust the water and seat temperature by pressing the
corresponding button to cycle through preset temperature levels.
Deodorizer
Press the "Stop" and "Water" button to adjust the deodorizer up
to 4 levels of intensity. When turned on, the deodorizer will
automatically activate when seated to reduce odors, and remains active for
1 minute after standing up.
•Single short beep - Deodorizer enabled
•Double short beep - Deodorizer disabled
Water Temp.
Seat Temp.
Room Temp. Low Medium High
Deodorizer
Off Low Medium High
Nozzle Oscillation
Press "Move" during a wash cycle to move the nozzle back and forth for
a wider cleaning experience. Change the nozzle position by pressing the
“Front” or “Rear” (^, v) buttons. This will not work during Turbo wash.
Automatic Oscillation Feature - You can set this function to
automatically oscillate. Sit on this product and press the “Move”
button for 3 seconds until you hear a chime. Proceed with Posterior
or Feminine Wash. To cancel, press the button again for 3 seconds.
Pulse
Press “Pulse” during a wash cycle to activate a pulsating spray pattern.
Change the water pressure with the “High” or “Low” (+, -) buttons.
Automatic Massage Feature - You can set this function to automatically
pulsate whenever the seat is occupied and the Posterior or Feminine
washes are in operation. Press the “Massage” button for 3 seconds until
you hear a chime. Proceed with Posterior or Feminine Wash. To cancel,
press the button again for 3 seconds.
Eco Mode
Press “Eco Mode” to toggle between energy saving features. Press
once to activate Eco 1. This keeps the warm water temperature at
90°F. Press again for Eco 2 (Smart Mode). This lowers the water
temperature when not in use. Press again to turnoff.
PRODUCT INFORMATION
Nozzle Cleaning
Automatic - This product has an automatic nozzle self-cleaning
function that cleans the nozzle before and after each use.
Manual - Press the “Posterior” button on the side panel without
occupying the seat. The nozzle will fully extend without spraying.
Gently clean the nozzle with a soft cloth or toothbrush. Press the
“Stop” button to retract the nozzle when you are finished.

INSTALLATION GUIDE
1. Turn Off Water
Turn off the water shut-off
valve. Drain the toilet tank
completely by flushing the
toilet. Unscrew the hose
connected to the toilet tank.
2. Remove Toilet Seat
Remove mounting bolts to
release the existing toilet
seat from the toilet.
3. Install Catch Plate
Place the catch plate and guides over each mounting hole. Insert the mounting
bolts through the guides, catch plate, and mounting holes. Slide the cone packing
and washers onto the bolts and fasten to secure the bidet.
INSTALLATION
Slide the bidet seat all the way onto
the catch plate until you hear a click.
4. Install Your BB-1000
Bolt
Bolt Guides
Catch Plate
Washer
Cone Packing
Nut
BEFORE INSTALLATION
Do not plug the power cord in until installation is complete.
Please contact our service center at 847.458.2334 for alternate
fittings or assistance with this process.
Existing
Toilet Hose

INSTALLATION
INSTALLATION
Toilet Tank
T-Valve
Toilet Hose
Bidet Hose
(Optional)
1/2” Conversion Nut
Shut-off Valve
Washer
5. Connect the Water Hoses
1. Install the t-valve onto the toilet tank. Ensure the rubber gasket is
properly seated inside the t-valve.
2. Connect the provided toilet hose to the water shut-off valve
and t-valve. You may also use your existing toilet hose.
3. Connect the bidet hose to the bidet seat and t-valve.
4. Open the water shut-off valve. Check for any leaking or dripping.
Use a wrench to tighten any loose connections.
*Shut-off valves may vary. If supplied parts do not fit, please call
847.458.2334. Alternate fittings may be available upon request.
Rubber Washer
*Inside T-valve
(Optional) May use
existing toilet hose
6. Plug It In!
1. Remove the adhesive cover from the back of bracket and
place the bracket where desired.
2. Insert supplied batteries and close the battery cover.
3. Ensure the batteries are inserted properly according to polarity.
Check for any water leaks. Plug the power cord into a dedicated 120V
power outlet and the LED light will start flashing. Wait until the LED light
stops flashing. Press the “Posterior” or “Feminine Wash button to fill the tank.
Adhesive Tape Wall
7. Mounting the Remote
*Inside conversion nut

1716
MAINTENANCE
Cleaning the Nozzle
Hold the “Posterior Wash” button for 3 seconds without occupying the seat to
extend the nozzle for manual cleaning. It can be cleaned using a toothbrush or
soft cloth. After cleaning the nozzle, push the “Stop” button once again and the
nozzle will retract.
Cleaning the BB-1000
•When you clean this product, do not use thinner, benzene or
toilet bowl cleaner, as it may cause discoloration or damage.
•Disconnect the power cord and use a wet cloth when you clean this product.
Replacing the Deodorizer
This product will not operate properly if the strainer is clogged.
Please clean the strainer regularly.
1. Unplug the power cord and close the water shut-off valve.
2. Unscrew the bidet hose from the bidet seat.
3. Clean the strainer with a small brush.
4. Re-connect the bidet hose and open the water shut-off valve.
5. Plug in the power cord.
Cleaning the Strainer
*Close shut-off valve
Insert the deodorizer cartridge into the unit. Follow the diagram below to
change the filter if necessary.
Cover
Deodorant
Deodorizer Case
MAINTENANCE

1918
Draining the Warm Water Tank
If you do not intend to use this product for 14 days or longer,
drain the water from this product’s warm water tank.
Before draining, unplug the power cord and wait 30 minutes until the
unit has cooled down. Do not insert your finger into the drain hole.
1. Disconnect the power plug.
2. Close the water shut-off valve.
3. Press the drain button until the water is completely
drained from water tank.
Open the water shut-off valve to refill and resume usage.
*Close shut-off valve
MAINTENANCE
MAINTENANCE
Removing the BB-1000
1. Disconnect the power plug.
2. Close water supply shut-off valve.
3. Drain the water from the bidet by holding the drain button as shown above.
4. Remove the bidet seat from toilet as illustrated.
Water Filter Maintenance
•Use of external water filters is only recommended in areas with
known hard water issues. If a filter is used, it should be replaced
every 3 months.
•This product is designed and intended for use exclusively
with Bio Bidet Carbon & Iodine water filters. The purchase
or use of any other water filter is not the responsibility of
Bio Bidet Innovation LLC. As such, any use of non Carbon or
Iodine water filters is prohibited and will void the warranty
for those Bio Bidet products. Bio Bidet will not be responsible
for any resulting damages or claims related to the misuse or
distribution of non Bio Bidet Carbon & Iodine filters.

2120
Specications BB-1000
Power Rang 120Vac, 60Hz, 660W
Water Inlet Pressure 0.04 ~ 0.74MPa (0.4 ~ 7.5 kgf/cm)
Power Cord 4 feet
Wash Device
Posterior Wash Max. 1.2 l/min ( Max. 0.32 GPM )
Feminine Wash Max.1.2l/min ( Max. 0.32 GPM )
Adjustable Water
Pressure
5 Levels
Warm Water Temp Room Temp - Low, Normal, High
Safety Devices Thermal fuse, Thermal switch,
Float switch
Heated Seat Temperature Room Temp - Low, Normal, High
Heater 55 W
Inlet Water Temp. 37.4°F ~ 95°F ( 3°C~ 35°C )
Ambient Temp. 37.4°F ~ 104°F ( 3°C~ 40°C )
Dimensions Elongated W: 17.9 in / L : 20.6 in / H : 7.28 in
Round W: 17.9 in / L: 1.4 in / H: 7.28 in
Weight (kg) 11.4 lbs
SPECIFICATIONS
Trouble Cause Solution
Water does not
spray
•The water tank
is not filled.
•The shut-off valve
is closed.
•Wait about one minute.
Press the desired washing
button once again.
•Open the shut-off valve
The unit is not
operang
•Disconnected the
power cord.
•The seat is not
occupied.
•Remote batteries
are depleted.
•Connect the power cord.
•Check the circuit breaker.
•Activate the seat sensor.
•Replace the batteries.
Water is leaking •Check the
water connections.
•If water is leaking from the
main unit, call Bio Bidet
customer support.
The water
pressure is weak
•The water pressure
level is set to “Low”.
•The strainer is clogged.
•Set the water
pressure to “High”
•Clean the strainer.
The water
is not warm
•The water temperature
is set to “Low”
•Continuous operation
has depleted the supply
of warm water.
•Set the water temperature
to “High” and wait
about 3 minutes.
The seat
and dryer
are not warm
•The seat & dryer
temperature is
set to “Low”
•Set the seat & dryer
temperature to “High”
TROUBLESHOOTING GUIDE

22
This warranty does not apply to the following items:
•Damage or loss sustained in a natural calamity such as fire,
earthquake, flood, thunder electrical storm, etc.
•Damage or loss resulting from any unreasonable use,
misuse, abuse, negligence, or improper maintenance of the product.
•Damage or loss resulting from removal, improper repair,
or modification of the product.
•Damage or loss resulting from sediments or foreign matter
contained in a water system.
•Damage or loss resulting from improper installation or from
installation of a unit in a harsh and/or hazardous environment.
This warranty gives you specific legal rights. You may have other rights which vary
from state to state. To obtain warranty repair service under this warranty, you must
take the product or deliver it prepaid to a Bio Bidet Innovation LLC service facility
together with a letter stating the problem, or contact a Bio Bidet Innovation LLC
distributor or products service contractor, or write directly to
Bio Bidet Innovation LLC, 7900 Illinois Rte 31, Crystal Lake, IL 60014.
This written warranty is the only warranty made by Bio Bidet Innovation LLC.
Repair or replacement as provided under this warranty shall be the exclusive
remedy available to the purchaser. Bio Bidet Innovation LLC shall not be
responsible for loss of the product or for other incidental, special or consequential
damages or expenses incurred by the purchaser, or for labor or other costs due to
installation or removal, or costs of repairs by others, or for any other expense not
specifically stated above. Except to the extent prohibited by applicable law, any
implied warranties, including that of merchantability or fitness for use, are
expressly limited to the duration this warranty. Some states do not allow limitations
on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so the above limitation and exclusion may not apply to you.
BIO BIDET INNOVATION LLC
7900 S RT 31 Crystal Lake IL 60014
T: 847.458.2334
F: 847.854.1296
[email protected]
www.biobidet.com
WARRANTY
WARRANTY
3 YEAR LIMITED WARRANTY
Bio Bidet Innovation LLC warranty its product to be free from manufacturing
defects under normal use and service for a period of three (3) years from
original date of purchase.
This warranty is extended only to the ORIGINAL PURCHASER.
•Bio Bidet Innovation LLC’s obligations under this warranty are limited to
repair or replacement, at Bio Bidet Innovation LLC’s option, of products
or parts found to be defective, provided that such products were properly
installed and used in accordance with instructions.
•Bio Bidet Innovation LLC reserves the right to make such inspections as
may be necessary in order to determine the cause of the defect.
•Bio Bidet Innovation LLC will not charge for labor or parts in connection
with warranty repairs or replacements.
•Bio Bidet Innovation LLC is not responsible for the cost of removal, return
and/or re-installation of products.
WARRANTY SUMMARY
3 Year Limited Warranty
•100% coverage on all parts and labor for the 1st year.
•75% coverage on all parts and labor for the 2nd year.
•50% coverage on all parts and labor for the 3rd year.
At-Home Repair Instructions Available
(Limited to certain products)
Service Center Repair Option*
*Warranty does not cover inbound shipping.
Customer Support Available via Phone, Chat, & Email.
847.458.2334
www.biobidet.com
[email protected]

THANK YOU!
Customer Support
7900 S Route 31 Crystal Lake, IL 60014
T: 847.458.2334
U.S. TOLL FREE: 877.339.5214
[email protected]
www.biobidet.com
12.13.22