BEMIS bioBidet USPA User manual

OWNER’S MANUAL
UB-6800H, UB-6800HS

3
TABLE OF
CONTENTS
PRODUCT INFORMATION
Important Safeguards
Safety Information
Main Unit & Parts
INSTALLATION
Installation Guide
How To Use
SETTINGS
Cleaning The Product
Maintenance
Troubleshooting Guide
Specifications
WARRANTY
Warranty
4 - 9
10 - 21
22 - 29
30 - 31

4 5
READ & SAVE ALL OPERATING INSTRUCTIONS
BEFORE INSTALLATION
NOTES
1. This product should be installed according to this manual.
2. Read this manual carefully and install it properly.
3. Keep this instruction manual in an easily accessible place.
4. Do not attempt to service this appliance yourself.
DANGER & WARNING - Reduces the risk of burns, electric
show, fire, or injury.
1. Close supervision is necessary when this appliance is used by or near infants,
elders, or handicapped persons. Children should not be permitted to use or
touch this appliance without adult supervision. Be sure to adjust the toilet seat
temperature for elders or people with sensitive skin.
2. Use this appliance only for its intended purpose as described in this manual.
Only use attachments recommended by the manufacturer.
3. Do not place or store this appliance in a location where it
can fall or be pulled into a tub or sink.
4. Do not operate this appliance if the cord is damaged or if the product is
dropped into water.
5. Do not touch a product that has fallen into the water. Unplug immediately.
6. Install the unit properly by following the installation procedure.
7. Keep the cord away from heated surfaces.
8. Never drop or insert any objects into any opening or hose.
9. Do not use outdoors.
10. Do not use aerosol or oxygen spray products on the unit.
IMPORTANT
SAFEGUARDS
PRODUCT INFORMATION PRODUCT INFORMATION
SAFETY
INFORMATION
DANGER - FOLLOW THESE BASIC INSTRUCTIONS TO
ENSURE THE SAFE USE OF YOUR APPLIANCE.
• Do not use a faulty or loose electric outlet or cord.
Doing so may result in a short circuit, electric shock, or fire.
• Do not obstruct the warm air dryer outlet.
If the outlet is obstructed by any objects, it may result in fire. If the outlet is
obstructed with hands, it may result in injury.
• Do not throw anything flammable into the toilet.
Doing so may result in fire.
• Do not splash water on this product.
Doing so may result in fire or electric shock.
• This product must be grounded.
Not doing so may result in a short circuit, electric shock, or malfunction.
• Do not use too many appliances on one power strip.
Doing so may result in fire or damage. Be sure to use a dry and clean outlet.
Do not use a faulty or loose outlet.
• Plug and unplug properly.
Do not plug or unplug with wet hands. It may result in injury or a short circuit.
Do not grab the cord when unplugging. Pull out the plug properly.
• Do not use the power when the seat and lid are disassembled.
Doing so may result in electric shock due to high voltage inside.
• Unplug when beeping or emitting a strange odor.
Unplug right away. Contact your dealer where you bought this appliance.
• Do not disassemble, repair, or modify this appliance.
Doing so may result in fire or electric shock.
• Dispose of used batteries according to the instructions.

6 7
SAFETY
INFORMATION
WARNING - FOLLOW THESE BASIC INSTRUCTIONS TO
ENSURE THE SAFE USE OF YOUR APPLIANCE.
• Do not step on or place heavy objects on this appliance.
Doing so may damage the unit.
Doing so may result in a malfunction of the appliance.
• Do not force the lid to close.
Doing so may cause malfunction.
• Be aware of urine splash on a nozzle or a dry air outlet.
Doing so may result in an unpleasant odor or failure of the appliance.
• Do not sit or lean against the lid or control panel.
Doing so may cause malfunction or breakage.
• Unplug if you do not plan to use the product for a long period of time.
• Do not pull out the water hose forcefully.
Doing so may cause water leakage.
• Use this appliance on a toilet only.
Not doing so may result in fire, injury, or electric shock.
• Do not place objects or small materials on this appliance.
WARNING: Risk of electric shock, fire, or personal injury. This product must be
grounded and connected only to a dedicated, nominal 120 VAC, 60 Hz circuit
protected by a minimum 15 A Ground-Fault Circuit-Interrupter (GFCI)
PRODUCT INFORMATION
• Be aware of low-grade burns.
Sitting on the heated seat for a long time may result in a low-grade burn.
Use care when being used by the following: Children, senior citizens, patients,
or others who can not control the temperature level. Sleeping pill users or
people who are on medication that causes drowsiness. Those who are
intoxicated or very tired, and may fall asleep while sitting on the unit.
• Unplug when cleaning.
Not doing so may result in fire or electric shock.
• Use the low temperature for children and people with disabilities.
Not doing so may cause irritation or injury.
PRODUCT INFORMATION

98
MAIN UNIT
& PARTS
Lid
Caution Label
Power
Cord
Side “Cleaning” Button
Side “Bidet” Button
Power Button
Power Light
Deodorizing Filter Unit Remote Control
2 Mounting Bolts
2 Washers
T-Valve & L-Valve
Mounting Plate
2 Cone Packings
2 Water Supply Hoses (15mm)
(7/8” to 3/8” & 1/2” to 1/2”)
Remote Control Bracket 3 AAA Batteries
2 Bolt Guides
2 Nuts
Deodorizing Filter
(Equipped with unit)
Nozzle For Cleansing/Posterior
Occupancy Sensor
Splash Guard
Heated Seat
Warm Air Dryer
Deodorizer
Nozzle For Bidet/Feminine
PRODUCT INFORMATION PRODUCT INFORMATION

10 11
INSTALLATION
GUIDE
CAUTION - Do not plug in until installation is finished.
Not doing so may cause damage.
If electric work is needed, please contact a qualified
electrician or serviceman only.
Remove the Existing Toilet Lid and Seat
1. Remove the nuts, washers, and cone packings from the
toilet seat and mounting bolts in the back of the toilet.
2. Remove the toilet seat, lid, and mounting bolts.
3. Keep them for potential future use.
Toilet Size (Elongated & Round Front)
• The toilet dimensions must be within those shown below. Do not install this
appliance on a toilet that does not meet these dimensional requirements.
Occupancy Sensor
• This appliance is equipped
with an occupancy sensor.
• The unit will not work unless
the seat is occupied.
INSTALLATION INSTALLATION
Mounting the Plate
Place the mounting plate over each mounting hole. Insert the mounting bolts
through the plate and mounting holes. Slide the cone packings and washers onto the
bolts and fasten tightly with nuts.
Occupancy Sensor
Seat

12 13
INSTALLATION
GUIDE
Attaching and Detaching Unit Connecting the Water Hose
*Shutoff valve may vary. If supplied parts do not fit, please call 847.458.2334
1. Slide the unit until it clicks into the plate.
2. Press and hold the drain/remove
button and pull forward.
Using Inline Carbon Filter
The use of an external inline carbon water filter is not required unless the
unit is used in an area with extreme hardwater. If a carbon filter is used, the
filter must be replaced every 6 months. Inline carbon filters can be purchased
from Bio Bidet. Use of non Bio Bidet filter is prohibited and will void the warranty
of the associated products.
INSTALLATION INSTALLATION
1. Close the shutoff valve by turning it clockwise.
2. Flush the toilet to empty the water tank.
3. Remove the existing water supply hose from the water tank.
4. Install the T-valve on the water tank.
5. Connect the water supply hose (7/8” to 3/8”) from the
T-valve to the shutoff valve.
6. Connect the other water supply hose (1/2” to 1/2”)
from the T-valve to the bidet seat.
7. Open the shutoff valve by turning it counter clockwise.
8. Check for any water leaking or dripping.
Optional 1/2” Spare Nut
(Available by request)
Water supply hose
(7/8” to 3/8”)
Water supply hose
(1/2” to 1/2”)

14 15
INSTALLATION
GUIDE (CONTINUED)
Trial Operation
1. Preparation
Plug the power cord in the outlet. The water tank will be filled in 2 minutes.
2. Checking All Functions
Cover the toilet bowl using the sheet of plastic wrap on the unit to prevent
the washing water from being sprayed out of the toilet. Then check for all
functions described in this manual.
3. Water temperature may vary while heating.
INSTALLATION INSTALLATION
HOW
TO USE
Specifications
• Power : AAA Size Battery X 3
• Operation Voltage : DC2.4V ~ 4.8V
• Operation Temperature : -20°C ~50°C (-4°F ~122°F)
Dry
1. Press “Dry” to activate the warm air dryer for 3 minutes.
- Press this button again to activate Turbo mode.
- The water pressure LED turns on during Turbo mode.
- The dryer strength is saved between uses.
2. Dryer will only operate when you sit on the seat.

16 17
Cleansing
• Press “Cleansing” to activate a posterior wash.
The function will stop after 3 minutes.
• Feature will only operate when you sit on the seat.
Bidet
• Press “Bidet” to activate a feminine wash.
The function will stop after 3 minutes.
• Feature will only operate when you sit on the seat.
User Settings
• Each button can save 2 settings. (Cleansing, Bidet)
How To Set User Presets
3. Press User 1 (or User 2) button. (The corresponding LED will blink)
4. Press Cleansing or Bidet.
5. Set the Water Pressure level by pressing the LOW / HIGH button.
6. Set the nozzle position by pressing the FRONT / REAR button.
7. Press User 1 (or User 2) again to save the settings.
(The LED will stay on for 2 seconds before turning off.)
How To Use User Presets
1. Press Cleansing or Bidet.
2. Press User 1 (or User 2). The saved settings will activate.
INSTALLATION INSTALLATION
HOW
TO USE (CONTINUED)
Stop
• Press “Stop” to stop current operation
Eco
• Press “Eco” to activate the power saving mode.
• Eco Mode : Water Pressure of Cleansing/Bidet/ set to Auto level 2,
Seat Temperature is set to approximately 28ºC (82.4ºF).
Temperature Adjustment (Water/Seat)
• There are 4 levels (Off-Low-Medium-High)
• 33°C (91.4°F) at “Low”(LED Green)
36°C (96.8°F) at “Middle”(LED Orange)
39°C (102.2°F) at “High”(LED Red)
Massage
• Press “Massage” to activate a rhythmic wash for massage effect
when you are using “Cleansing”,”Bidet”,”Kids” or “Auto”.
Kids
• Press “Kids” to change all functions to be suitable for children.
• It will automatically operate from Cleansing to Dry with
adequate water pressure (Level 1) and nozzle position (Level 5).
• Kids feature will only operate when you sit on the seat.
• This feature should be used under the supervision of an adult.

18 19
HOW
TO USE (CONTINUED)
Auto
• Press “Auto” during the “Cleansing” or “Bidet” operation to
activate the following sequence.
• Cleansing wash (27 sec.) - Oscillating wash (20 sec.)
Oscillating Massage (80 sec.) - Dry (3 min.)
Nozzle Position
• The nozzle position can be adjusted by pressing the
FRONT or REAR button to 5 levels.
• It can only be adjusted during “Cleansing”, “Bidet”, “Auto”, and “Kids” mode.
Water Pressure (High/Low)
• The water pressure can be adjusted by pressing the HIGH or LOW button
to 5 levels during “Cleansing”, “Bidet”, and “Kids” mode.
Aerated Spray
• This gentle but strong spray cleanses with additional aeration while using
“Cleansing”, “Bidet”, “Kids” or “Auto” mode.
LED
• Press the button to turn the light on or off.
INSTALLATION INSTALLATION
Deodorization
• Press the button to turn the Deodorization On/Off.
• When the appliance is in use, the deodorizer will work up to a
maximum of 20 minutes.
• If a user stands up, the function will stop after 1 minute.
Sound
• Press the button to enable or disable the beeping sound.
Auto Nozzle Cleansing
• Press “FRONT” for 2 seconds to activate Auto Nozzle Cleansing
• Nozzle cleansing will work for 3 minutes.
• Press the “Stop” button to stop the function while operating.
• The function only operates while standing up.
Auto Nozzle Sterilization
• Press “REAR” for 2 seconds to activate Auto Nozzle Sterilization
• Nozzle cleansing will work for 3 minutes.
• Press the “Stop” button to stop the function while operating.
• This function only operates while standing up.

20 21
HOW
TO USE (CONTINUED)
Factory Reset Values
• Water Temperature : OFF
• Seat Temperature : OFF
• Cleansing/Bidet/Auto : Water Pressure = level 3
• Nozzle Position = level 3
• Dry Temperature: level 3
• Deodorization : ON
• LED(Night Light): ON
• Delete “User 1” and “User 2” setting
• Remote Controller ID : 00
• Sound : OFF
• Eco : OFF
How to Reset Remote Control
• After inserting the batteries, all of the LEDswill blink once.
• Press the “Stop” button for 3 seconds and the LED will blink three times.
How to Set ID (Remote Control)
• Press the “HIGH” button for 3 seconds to set ID.
• Press the “HIGH” or “LOW” buttonto change the ID numbers accordingly.
• Press the “Stop” button on on the side of the seat until it powers off.
Continue to hold the “Stop” button.
• Then set the Remote Control ID number
while continuing to hold the “Stop” button.
• The appliance will beep when the ID has been saved.
INSTALLATION INSTALLATION
Side Control Buttons
• Use the side control buttons when the remote control is broken
or the batteries are dead.
• Press the power button while standing to turn the appliance ON or OFF.
• Press the “Bidet” button to activate a feminine wash when you sit on the seat.
Press the button again to stop the function.
• Press the “Cleansing” button to activate a posterior wash when
you sit on the seat. Press the button again to stop the function.

22 23
CLEANING
THE PRODUCT
NOZZLE CLEANING
Manual Cleaning
1. Make sure the occupied sensor
is not activated. (Do not sit on
the seat or place hands on
the seat sensor.)
2. Press the Front button for
2 seconds to extract the bidet
nozzle. Press the button again
to extract the cleansing nozzle.
3. Use a toothbrush or soft
cloth to clean the nozzle.
4. Press the Stop button to
retract the nozzle.
Auto Cleaning
1. Press the Rear button for 2 seconds
to start auto cleaning. The nozzle
will be cleaned for 30 seconds and
retracted automatically.
2. Press the Stop button while
cleaning to retract the nozzle.
3. Do not force to push or pull the
nozzles while cleaning.
CAUTION: Do not forcefully push, pull, or bend the nozzles. It may result
in damage. Make sure to use the “Stop” button on the remote control.
SETTINGS SETTINGS
Strainer Maintenance
• This appliance will not operate properly if the strainer is clogged.
Be sure to clean the strainer regularly.
Cleaning The Body
1. Regularly wipe off the body with a dry soft cloth, sponge, or wash
with a damp cloth and mild detergent.
2. In order to protect the plastic unit, only use neutral cleansers.
(Do not use toilet cleaners, home cleansers, bleach, benzene,
paint thinner, cresol (Lysol).

24 25
SETTINGS SETTINGS
1. Unplug the Power
Supply Cord.
• Not doing so may cause electric
shock or fire.
2. Close the Shutoff Valve.
3. Drain
• Press the drain/remove
button to drain the tank.
MAINTENANCE
Drain water from the unit when not using it for an extended period of time.
Prevent Freezing
1. Make sure the power cord is plugged in properly.
2. Set the temperature of water to low or middle. (Freezing can be prevented
by thermal efficiency of the water tank.) If there is no heating system in the
toilet, wrap pipes with a cloth or other materials.
3. If the unit has not been used for a long time in the winter, unplug and
drain the water from the water tank and pipes thoroughly. Refer to the
drain instructions above.
4. Detaching Unit
• After the draining is
complete, press and hold
the drain/remove button
and pull forward.

26 27
SETTINGS SETTINGS
TROUBLESHOOTING
GUIDE
PROBLEM POSSIBLE
CAUSE
POSSIBLE
SOLUTION
Unit
completely
fails to work
or power on
1. Power outage
2. The unit is
not plugged in.
3. Faulty outlet
4. Occupancy sensor
is not activated.
1. Reset the GFI outlet.
2. Plug the power cord
in to a GFI outlet.
3. Test another appliance
in the outlet.
4. Activate the occupancy
sensor on the unit.
Nozzle does
not extend
1. Remote control
is not working.
2. Nozzle is dirty.
3. Occupancy sensor
is not activated.
4. Seat riser is
covering the
occupancy sensor.
1. Replace the remote
control batteries and try to
operate the unit with the
side control panel.
2. Clean the nozzle.
3. The occupancy
sensor on the unit.
4. The seat riser must go
underneath the bidet seat.
Low water
pressure
1. Clogged nozzle tip.
2. Water pressure
is set to low on
remote.
1. Clean the nozzle tip.
2. Raise the water pressure
on the remote control.
Seat is not
heating
1. Unit is set on
Economy mode.
2. Remote control
batteries.
1. Turn off Economy mode.
2. Replace batteries
PROBLEM POSSIBLE
CAUSE
POSSIBLE
SOLUTION
Stops in
the middle
of use
1. Washing or
drying exceeded
cycle time.
2. Occupancy sensor
lost contact.
3. Clogged nozzle tip.
1. Press the wash or
dry mode again.
2. Activate the skin sensor
with full skin contact
through the entire
cleansing period.
3. Clean the nozzle tip
Water
coming out
from the
nozzle
unexpectedly
1. Self-cleaning 1. The unit will self-clean the
nozzle before and after
each use automatically.
Water leaking
continuously
1. Leaking from hose
connection at
the unit.
2. Leaking from
T-valve
3. Leaking from
behind or under
the tank.
1. Check to make sure that all
rubber washers are in place
and do not over tighten the
connection but it should
be secure.
2. Check to make sure that
the rubber washer is in
place with the flat side
pointing up.
3. Check that the drain is
not opened on the unit. If
the unit continues to leak,
immediately disconnect
it from the water supply,
drain the tank, and
contact Bio Bidet
customer support.

29
SPECIFICATIONS
ITEM UB-6800H, 8B-6800HS
Standard power supply AC 120V, 60Hz 1248W
Water Supply
Water connection Direct connection to tap water
Water pressure 0.07 MPa ~ 0.74 MPa
Cleansing
Spray for cleansing 700 ± 150 ml/min
Spray for bidet 700 ± 150 ml/min
Water capacity 70 ml
Water temperature Room temp ~ 39°C (102.2°F)
Heater capacity 1200 W
Safety feature Thermal switch, temperature fuse,
floating switch
Dry
Air temperature Room temp ~ 60°C (140°F)
Heater capacity 250 W
Safety feature Temperature fuse
Heated Seat
Seat temperature Room temp ~ 40°C (104°F)
Heater capacity 48 W
Safety feature Temperature fuse
Deodorization method Catalytic filter
Circuit breaker Within 15mA 0.03 seconds
Length of power cord 4 ft
Dimensions
Elongated (W) 392mm (15.43 inches) x (L) 520 mm
(20.47 inches) x (H) 145 mm (5.71 inches)
Round Front (W) 392mm (15.43 inches) x (L) 500 mm
(19.68 inches) x (H) 145 mm (5.71 inches)
Weight 4.4Kg (9.7 lbs)
• Recommended water supply pressure is 0.1 ~ 0.69 MPa.
• The minimum available water supply pressure is 0.07 MPa,
however 0.1 MPa pressure, water spray pressure might not be adequate.
SETTINGS

30 31
WARRANTY
WARRANTY
USPA PRO Personal Hygiene Appliance Limited Warranty
We warrant our products to be free from manufacturing defects under normal
use and service for a period of 3 years prorated base as below from the date
of your purchase.
• 100% Coverage of all parts and labor for the entire product
for the first year from the original date of purchase.
• 75% Coverage of all parts and labor for the entire product
for the second year from the original date of purchase.
• 50% Coverage of all parts and labor for the entire product
for the third year from the original date of purchase.
Warranty is valid within the United States and Canada only.
Our obligation to you under this warranty is limited to repair or replacement,
at our option, of defective products or parts, provided that the products were
properly installed and used in accordance with instructions. We reserve the
right to make inspections in order to determine the cause of the defect. We
will not charge for labor or parts in connection with warranty repairs or
replacement. We are not responsible for the cost of removal, return, and/or
re-installation of products.
This limited warranty does not apply to:
• Damage or loss from fire, earthquake, flood, storm, etc,
• Damage or loss resulting from any unreasonable use,
abuse negligence, or improper maintenance.
• Damage or loss from improper installation,
removal, repair, or modification.
• Damage or loss resulting from sediment or other
matters contained in your water system.
This warranty gives you specific legal rights.
For warranty or service information, please contact your dealer where you
bought this appliance or us. Only the original purchaser may submit a claim
under this limited warranty.
This limited warranty is our only warranty covering your product. Repair or
replacement as provided under this warranty shall be the exclusive remedy available
to you. We shall not be responsible for the loss of the product or for other incidental,
or consequential damage or expenses you may incur or for labor or other costs due to
installation or removal, or cost of repairs by others, or for any other expense not spe-
cifically stated above. Except to the extent prohibited by applicable law, any implied
warranties including that of merchantability or fitness for use, are expressly limited to
the duration of this warranty.
Warning! We are not responsible or liable for any failure of, or damage to, this
plumbing product component caused by in-tank bowl cleaners containing chlorine
(calcium hypochlorite).
Note: The use of a high concentration of chlorine related products can seriously
damage the fittings. This damage can cause leakage and serious property damage.
For more information, please contact your dealer or us.
BIO BIDET INNOVATION LLC
7900 S RT 31 Crystal Lake IL 60014
T: 847-458-2334
F: 847-854-1296
[email protected]
www.biobidet.com
WARRANTY

THANK YOU
Technical Support/Customer Service
7900 S Route 31 Crystal Lake, IL 60014
T: 847.458.2334
U.S. TOLL FREE: 877.339.5214
[email protected]
www.biobidet.com