BEMIS BioBodet HD-4000 User manual

User Manual
HD-4000

3
TABLE OF
CONTENTS
PRODUCT INFORMATION
Features...............................................................................5
Parts.......................................................................................6
Dimensions.......................................................................7
PRODUCT INSTALLATION
Pre-Installation..............................................................8
Installation........................................................................9
PRODUCT OPERATION
How To Use.....................................................................13
MAINTENANCE
Cleaning............................................................................14
Short Term Non-Use................................................14
Warranty............................................................................15

5
•Tilted control panel
•High-quality ABS material
•Premium quality metal inlet and installation parts
•Dual nozzle
•Ambient temperature bidet wash
•Adjustable water pressure
•Unified internal brass valve
•Durable braided metal cold water hose
•No electricity or batteries required
•Adjustable toilet fit
•One-year warranty
FEATURES

6 7
Bidet attachment
PARTS DIMENSIONS
2 Adjustable
mounting brackets
*T-Valve connector
with rubber cone
washer
(7/8” x 7/8” x 3/8”)
27.5” Braided
metal hose
2 Non-slip mats
Teflon tape
3 Toilet bumpers
*Alternate fittings available, contact [email protected]om
5.49 in
15.73 in
2.48 in
3.54 in
0.24 in
12.79 in
3.23 in
8.65 in
4.32 in
12.37 in
2.87 in

8 9
PRE-INSTALLATION
Please be advised that the provided T-Valve
should be installed at the fill valve under the
toilet tank, NOT down at the water supply
coming from the wall.
Inspect your current water supply line that
connects to the toilet tank fill valve to ensure it
is a flexible water supply hose before installing
the HD-4000. The hose needs to be 7/8” (to
connect to the T-Valve we provided) on one
end and either 3/8” or 1/2”, depending on your
wall valve, on the other end.
If you do not have access to the fill valve under
the toilet tank, contact Bio Bidet Customer
Service at 847.458.2334 and we may be able
to provide alternative fittings.
WARNING: Use care to avoid cross threading
or over tightening the connection. Over
tightening can cause leaking.
NOTICE: Observe all local plumbing, electrical
and building codes. This device is designed
for connection to a cold water source with
a pressure of 20-80 psi.
INSTALLATION
1. Remove the existing
toilet seat by locating the
bolts and nuts, typically
under a plastic cover, and
removing them first.
2. Close the water supply
valve and flush the toilet
completely so that there
is little to no water left in
the toilet tank.
3. Disconnect the water
hose from underneath
the toilet tank.
4. Connect the 7/8” T-Valve
to the toilet fill valve
where you just removed
the water hose from.
Make sure the rubber
washer is properly seated
with the narrow side up.

10 11
5. Attach the water supply
hose that comes from
the water shut off to the
bottom of the T-Valve.
6. Connect the metal
hose we supplied
to the open side of
the T-Valve.
7. Insert the rubber non-slip
mats to the bottom of the
bidet. Place the toilet seat
back on the toilet over
the bidet and secure
8. Place the circular
mounting brackets into
the bidet attachment.
9. Place the bidet
on the toilet with the
mounting brackets
over the bolt holes
and make any needed
adjustments to make
sure the bidet is
centered on the toilet.
10.Place the toilet seat
back on the toilet over
the bidet and secure
the bolts down so that
the seat and bidet
attachment are stable.
11. Connect the hose
from step 6 to the bidet
water connection
underneath the handle
of the HD-4000.
12. Slowly turn the water
supply valve back
on, check for leaks,
and test the unit for
functionality.
INSTALLATION (CONT.)

12 13
13. After installing your
bidet attachment,
check to see if there is a
gap between the toilet
base and toilet seat.
14. If necessary, place
the bumpers on the
underside of your toilet
seat as indicated above. If there are no immediate leaks, check again
in about 5-10 minutes and your HD-4000 is
ready for use!
If any leaks occur, check all rubber washers and
make sure all connections are tight and secure.
HOW
TO USE
For back wash, turn the control dial to the left
towards the “ “ position.
For front/feminine, turn the control dial to the
right towards the “ “ position.
The further the knob is turned, the higher the
water pressure will be. Adjust the control dial
to choose the comfortable pressure you want.
The control dial doesn’t reset automatically,
please turn it off manually.
INSTALLATION (CONT.)

14 15
CLEANING
SHORT TERM
NON-USE
If the product will not be used for more than
a few days, it is highly recommended that the
water supply valve is turned off.
Your HD-4000 is made with a high grade
fire-retardant ABS resin. Using hard cleaning
chemicals can weaken the material, causing it
to damage and develop cracks.
1. Clean the HD-4000 by wiping the
surface area with a damp cloth regularly.
2. Do not use harsh detergents or any
cleaning tools with bristles on your bidet.
Steam cleaning is the preferred cleaning
method for your bidet. For a deep, chemical
free clean, consider the BioMist Bidet Cleaner.
WARRANTY
Your Bio Bidet is warranted against defects in materials or workmanship for 1 year
from the date of original purchase. Defective parts or a defective products returned
to Bio Bidet will be repaired with new or comparable rebuilt parts or exchanged for a
refurbished Bio Bidet as determined by Bio Bidet in their sole discretion.
This limited warranty given by Bio Bidet covers all defects encountered in normal
use of Bio Bidet, and do not apply in the following cases:
1. Loss of or damage to Bio Bidet due to abuse, misuse, tampering.
mishandling, improper packaging by you, alteration and failure to
follow operating instructions.
2. Use of parts or supplies (other than those by Bio Bidet’s dealers) that cause
damage to Bio Bidet.
3. Replacement of discolored or stained parts caused by chlorine, bleach,
ammonia and other chemicals, cleaning supplies, oxidation, normal wear
and tear.
4. Damage to or malfunction of the unit as a result of improper and
negligent installation.
5. Any and all damages to plumbing, walls, floors, ceiling and personal properties
resulting from water leaks or breakage. The product must be used at the user’s
own risk. Therefore, the owner hereby releases the manufacturer and distributor
from any and all claims for damages where the above condition exits.
No implied warranty, including any implied warranty of merchantability or fitness or a particular
purpose, applies to BBC Innovation LLC bidet after the applicable period of the express limited
warranty stated above, and no other express warranty or guaranty, except as mentioned above,
given by any person or entity with respect to Bio Bidet shall bind Bio Bidet, (Some States and
provinces do not allow limitations on how long an implied warranty, so the above limitation may
not apply to you). BBC Innovation LLC shall not be liable for revenues or profits, inconvenience,
expense for substitute equipment or service, or any other special, incidental or consequential
damages caused by the use or misuse of, or inability to use, Bio Bidet, regardless of the
possibility and foresee-ability of such damages. In no event shall recovery of any kind against
BBC Innovation LLC be greater in amount than the purchase price of the product and causing
the alleged damage. Without limiting the foregoing, you assume all risk and liability for loss,
damage or injury to you and your property and to others and their property arising out of use
or misuse of, or inability to use, the Bio Bidet not caused directly by the negligence or
BBC Innovation LLC. This limited warranty shall not extend to anyone other than the original
purchaser of the Bio Bidet.

Thank You
Technical Support/Customer Service
7900 S Route 31 Crystal Lake, IL 60014
T: 847.458.2334
U.S TOLL FREE: 877.339.5214
[email protected]om
www.biobidet.com