Bend-Pak P-9000LTF User manual

BendPak, Inc. Corporate Oce
1645 Lemonwood Drive
Santa Paula, CA 93060 USA
Toll Free US/Canada: 1-800-253-2363
Fax: [phone]
[email protected]om
Customer Service Desk / Warranty
Customer Service Representatives
Oce Tel: [phone]
Toll Free US/Canada: 1-800-253-2363
Fax: [phone]
customerservic[email protected]
Parts Orders
Customer Service Representatives
Oce Tel: [phone]
Toll Free US/Canada: 1-800-253-2363
Fax: [phone]
[email protected]om
Domestic Sales & Service
USA Sales Representatives
Oce Tel: [phone]
Toll Free US/Canada: 1-800-253-2363
Fax: [phone]
[email protected]om
International Sales & Service
Oce Tel: [phone]
Exports Dept: 1-805-933-9970 EXT. 192
Ext. Toll Free US/Canada: 1-800-253-2363
Fax: [phone]
bpkex[email protected]om
Service Manual
SERVICE PARTS & DIAGRAMS
This guide is a troubleshooting reference used for maintaining and
servicing your Bend Pak product. It provides comprehensive information
on identifying serviceable parts and components and assists in
troubleshooting problems and performing assembly /disassembly
procedures.
BENDPAK
P-9000LTF
PRODUCT SKU
5175155
DRAWING Nº
5260197
CATEGORY
Low-Rise Scissor Li
REV
Version W
DATE
09.27.2022

DIMENSIONS ARE IN MM
☺
13
2
4
5
4
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
U
REPLACED LABELS WITH COLORS &
GRAPHICS NOTE, REPLACED 5940057 WITH
PACKAGING INSTRUCTION NOTE, UPDATED
BOM REVISION
09/21/2021 CA 01339
V ADDED POWER UNIT AND REFERENCE NOTE 12/13/2021 CA 01368
W
FLIPPED HYDRAULIC LINE ORIENTATION,
UPDATED BOM REVISIONS
08/23/2022 TM 01433
ITEM NO PART NUMBER DESCRIPTION QTY REV
1 5215780 SHORT POWER UNIT CONSOLE ASSEMBLY 1 G
2 5215498 P9000 LT SERIES R.H. RAMP ASSEMBLY 1 K
3 5215500 P9000LT L.H. RAMP ASSEMBLY 1 K
4 5250034 P9000LT PARTS BOX 1 N
5 REF POWER UNIT 1 -
SHEET 1 OF 3
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
W
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
NOTE: UNLESS OTHERWISE SPECIFIED .
JM
5260197
P9000LTF PRODUCTION LIFT
01/10/2018
DO NOT SCALE DRAWING
1:20
SCALE:
THIRD ANGLE PROJECTION
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING 2.
SEE COLORS & GRAPHICS FOR LABEL PLACEMENT 3.
POWER UNIT REFERENCE ON PURCHASE ORDER 4.

DIMENSIONS ARE IN MM
☺
A
B
3
1
8
7
7
2
14
DETAIL A
SCALE 2 : 15
11
10
13
DETAIL B
SCALE 1 : 10
9
4
12
5
6
15
16 17
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
L
ADDED 5550089, REPLACED 5300002 WITH
5210232, REMOVED (1) 5550395
09/24/2019 TM 01128
M
ADDED 5580012, REMOVED 5590175, 5550087
AND 5550486
03/30/2020 TM 01152
N REPLACED 5550089 WITH 5550004 09/02/2020 CA 01205
ITEM
NO
PART
NUMBER
DESCRIPTION QTY REV
1 5530456 AB 3/4" x 4 - 3/4" 12 --
2 5530326 AB Ø3/8" x 2-1/4" 2 --
3 5210232 LOW RISE SCISSOR LIFT RUBBER PAD KIT, SET OF 8 1 A
4 5550001 FTG NPL -04 COMP x -02 NPT 2 --
5 5550008 FTG ELB -04 JIC -06L ORB 2 --
6 5550086 FTG ELB -04 NPT x -04 JIC 2 --
7 5570040
P9000/SP-7XL HYDRAULIC HOSE ASSY Ø6.35 x 4270mm SB
2 D
8 5570795 1/4" POLY-FLO TUBING 5182mm --
9 5550395 FTG TEE -04 COMP x -04 COMP x -04 COMP 2 --
10 5545340 WASHER M8 x24 FLAT 4 --
11 5530304 HHB M8 x 1.25 x 20 4 --
12 5215466 P9000 HYDRAULIC LINE ASSEMBLY 2 C
13 5715003 POWER UNIT VIBRATION DAMPENER 1 B
14 5900022 P9000LT INSTALLATION AND OPERATION MANUAL 1 --
15 5550095 FTG NPL -04 JIC x -04 JIC 2 --
16 5550004 FTG ELB 1/4 TUBE INS 3/8 NPT 1 --
17 5580012 LIQUID PTFE THREAD SEALANT 50ml 1 --
NEXT ASSEMBLY
5260196
5260197
WHERE USED
P9000LT
P9000LTF
SHEET 1 OF 1
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
N
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
NOTE: UNLESS OTHERWISE SPECIFIED .
JM
5250034
P9000LT PARTS BOX
08/05/2015
DO NOT SCALE DRAWING
1:25
SCALE:
THIRD ANGLE PROJECTION
OR
09/04/2020
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING 2.

DIMENSIONS ARE IN MM
☺
2
1
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
A PRODUCTION RELEASE, DERIVED FROM 5210944 09/18/2019 TM 01128
NEXT ASSEMBLY
ACCESSORY
5250020
5250021
5250034
5250054
5250062
5250063
5250064
5250110
5250174
5250317
5250318
ITEM
NO
PART
NUMBER
DESCRIPTION QTY REV
1 5300862 LOW RISE SCISSOR LIFT 75mm RUBBER PAD KIT, SET OF 4 1 A
2 5300861 LOW RISE SCISSOR LIFT 38mm RUBBER PAD KIT, SET OF 4 1 A
WHERE USED
LR-60 SERIES
DLR-6 SERIES
MDS-6 SERIES
P9000LT SERIES
SP-7XE SERIES
SHEET 1 OF 1
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
A
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
NOTE: UNLESS OTHERWISE SPECIFIED .
TM
5210232
LOW RISE SCISSOR LIFT
RUBBER PAD KIT, SET OF 8
09/18/2019
DO NOT SCALE DRAWING
1:5
SCALE:
THIRD ANGLE PROJECTION
CA 11/01/2019
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING 2.

DIMENSIONS ARE IN MM
☺
2
1
3
NEXT ASSEMBLY
5250034
ITEM NO PART NUMBER DESCRIPTION QTY REV
1 5755154 P9000 HYDRAULIC LINE 1 C
2 5550297 FTG FS Ø6 OD TUBE 2 --
3 5550296 FTG FN Ø6 x -04 JIC F 2 --
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
A PRODUCTION RELEASE, DERIVED FROM 5215407 05/13/2016 TM 00761
B UPDATED BOM REVISION 11/21/2016 TM 00781
C UPDATED BOM REVISION 07/21/2017 TM 00852
SHEET 1 OF 1
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
C
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
TM
5215466
P9000 HYDRAULIC LINE
ASSEMBLY
05/13/2016
DO NOT SCALE DRAWING
1:1
SCALE:
THIRD ANGLE PROJECTION
ASSEMBLE ITEMS AS SHOWN 1.
SLIDE FLARE FITTINGS ON TO TUBE AS SHOWN BEFORE FLARING 2.
FLARE TUBE USING 37° FLARING TOOL ON BOTH ENDS 3.
INSERT FLARE SLEEVE INTO ENDS TO COMPLETE ASSEMBLY 4.
NOTE: UNLESS OTHERWISE SPECIFIED .

DIMENSIONS ARE IN MM
☺
A
16
26
17
19
23
3
24
2
25
11
21
22
14
4
20
10
1
28
29
13
12
DETAIL A
SCALE 1 : 4
18
7
5
6
8
15
9
27
NEXT ASSEMBLY
5260196
5260197
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
H UPDATED BOM REVISION 04/21/2020 CA 01161
J REMOVED 5550025, UPDATED BOM REVISION 07/16/2021 CA 01317
K UPDATED BOM REVISION 08/23/2022 TM 01433
ITEM
NO
PART
NUMBER
DESCRIPTION QTY REV
1 5601220 P9000LT R.H. BASE WELDMENT 1 B
2 5600886 P-9000/P-9000F R.H. SAFETY BAR WELDMENT 1 C
3 5600969 P-9000/P-9000F UPPER HINGE PIN WELDMENT 1 A
4 5601194 P9000 SAFETY BAR PIVOT ARM WELDMENT 2 B
5 5502195 AIR CYLINDER, Ø19mm x 25 STROKE 1 --
6 5505625 FEMALE ROD END M6 x 33 1 --
7 5550087 FTG ELB -04 COMP x -02 NPT 1 --
8 5545026 WASHER M6 x Ø12 SL 1 --
9 5535357 NUT M6 x 1.0 NL 1 --
10 5505400 COTTER PIN Ø6 x 50mm 3 --
11 5601221 P9000 LT SERIES RAMP HINGE ARM PIVOT PIN WELDMENT 4 A
12 5601244 P9000 LT SERIES BASE HINGE ARM PIVOT PIN WELDMENT 4 A
13 5535001 NUT M8 x 1.25 NL 4 --
14 5601052 P9000 SAFETY LOCKOUT BAR WELDMENT, RH 1 D
15 5530019 HHB M6 x 1 x 16mm 1 --
16 5215499 P9000LT R.H. TOP DECK ASSEMBLY 1 C
17 5601222 P-9000LT HINGED RAMP WELDMENT 1 B
18 5530047 HHB, M6 x 1 x 30mmL 1 --
19 5746178 P-9000/P-9000F CLEVIS PIN 1 B
20 5545202 WASHER M8 x Ø15 SL 8 --
21 5545341 WASHER M10 x Ø20 FLAT 8 --
22 5530025 HHB M8 x 1.25 x 12mm 8 --
23 5756035 P-9000/P-9000F SAFETY BAR SPACER 1 A
24 5502030 CYLINDER ASSEMBLY Ø2.0 x 17.75 1 H
25 5746425 P9000 HINGED RAMP PIN 2 A
26 5505006 COTTER PIN Ø3.2 x 20mm 4 --
27 5535230 NUT 1/4-28 JN 1 --
28 5620613
P9000LT SERIES ASYMMETRIC HINGE DOUBLE ARM
WELDMENT
1 A
29 5620612 P9000LT SERIES ASYMMETRIC HINGE ARM WELDMENT 2 A
WHERE USED
P9000LT SERIES
SHEET 1 OF 1
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
K
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
NOTE: UNLESS OTHERWISE SPECIFIED .
TS
5215498
P9000LT R.H. RAMP
ASSEMBLY
01/09/2018
DO NOT SCALE DRAWING
1:18
SCALE:
THIRD ANGLE PROJECTION
OR 08/25/2022
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
ASSEMBLE ITEMS AS SHOWN 2.

DIMENSIONS ARE IN MM
☺
ISOMETRIC VIEW
FOR REFERENCE ONLY
DO NOT SCALE
1
2
3
4
NEXT ASSEMBLY
5215498
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
A PRODUCTION RELEASE, DERIVED FROM 5215431 01/08/2018 TS 00903
B
REPLACED 5715021 WITH 5715035, ADDED
5530366, UPDATED BOM REVISION
09/26/2019 TM 01128
C
REPLACED 5715035 WITH 5715049, 5530366
WITH 5530364, ADDED 5535357, UPDATED BOM
REV
07/29/2022 TM 01433
ITEM NO PART NUMBER DESCRIPTION QTY REV
1 5601217 P-9000/P-9000F R.H. TOP DECK WELDMENT 1 C
2 5715049 P9000 RAMP BOLT-ON RUBBER PAD 2 A
3 5530364 ELEVATOR BOLT M6 x 1.0 x 25 8 A
4 5535357 NUT M6 x 1.0 NL 8 B
WHERE USED
P9000LT
P9000LTF
SHEET 1 OF 1
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
C
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
NOTE: UNLESS OTHERWISE SPECIFIED .
TS
5215499
P9000LT R.H. TOP DECK
ASSEMBLY
01/08/2018
DO NOT SCALE DRAWING
1:8
SCALE:
THIRD ANGLE PROJECTION
OR 08/26/2022
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
SEE COLORS & GRAPHICS FOR LABEL PLACEMENT 2.
SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING 3.
ASSEMBLE ITEMS AS SHOWN 4.

DIMENSIONS ARE IN MM
☺
A
23
22
25
20
26
2
1
5
6
14
19
10
11
24
4
3
28
29
16
17
21
DETAIL A
SCALE 1 : 4
18
8
7
9
1312
27
15
NEXT ASSEMBLY
5260196
5260197
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
H UPDATED BOM REVISION 04/21/2020 CA 01161
J REMOVED 5550025, UPDATED BOM REVISION 07/16/2021 CA 01317
K UPDATED BOM REVISIONS 08/23/2022 TM 01433
ITEM
NO
PART
NUMBER
DESCRIPTION QTY REV
1 5601219 P9000LT L.H. BASE WELDMENT 1 B
2 5601222 P-9000LT HINGED RAMP WELDMENT 1 B
3 5215745 P9000LT L.H. TOP DECK ASSEMBLY 1 C
4 5601051 P9000 SAFETY LOCKOUT BAR WELDMENT, LH 1 D
5 5600969 P-9000/P-9000F UPPER HINGE PIN WELDMENT 1 A
6 5505400 COTTER PIN Ø6 x 50mm 3 --
7 5502195 AIR CYLINDER, Ø19mm x 25 STROKE 1 --
8 5550087 FTG ELB -04 COMP x -02 NPT 1 --
9 5505625 FEMALE ROD END M6 x 33 1 --
10 5601194 P9000 SAFETY BAR PIVOT ARM WELDMENT 2 B
11 5535001 NUT M8 x 1.25 NL 4 --
12 5530019 HHB M6 x 1 x 16mm 1 --
13 5545026 WASHER M6 x Ø12 SL 1 --
14 5600887 P-9000/P9000F L.H. SAFETY BAR WELDMENT 1 C
15 5535357 NUT M6 x 1.0 NL 1 --
16 5601221 P9000 LT SERIES RAMP HINGE ARM PIVOT PIN WELDMENT 4 A
17 5601244 P9000 LT SERIES BASE HINGE ARM PIVOT PIN WELDMENT 4 A
18 5530047 HHB, M6 x 1 x 30mmL 1 --
19 5545202 WASHER M8 x Ø15 SL 8 --
20 5545341 WASHER M10 x Ø20 FLAT 8 --
21 5530025 HHB M8 x 1.25 x 12mm 8 --
22 5756035 P-9000/P-9000F SAFETY BAR SPACER 1 A
23 5746178 P-9000/P-9000F CLEVIS PIN 1 B
24 5502030 CYLINDER ASSEMBLY Ø2.0 x 17.75 1 H
25 5746425 P9000 HINGED RAMP PIN 2 A
26 5505006 COTTER PIN Ø3.2 x 20mm 4 --
27 5535230 NUT 1/4-28 JN 1 --
28 5620613
P9000LT SERIES ASYMMETRIC HINGE DOUBLE ARM
WELDMENT
1 A
29 5620612 P9000LT SERIES ASYMMETRIC HINGE ARM WELDMENT 2 A
WHERE USED
P9000LT
P9000LTF
SHEET 1 OF 1
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
K
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
NOTE: UNLESS OTHERWISE SPECIFIED .
TS
5215500
P9000LT L.H. RAMP
ASSEMBLY
01/09/2018
DO NOT SCALE DRAWING
1:18
SCALE:
THIRD ANGLE PROJECTION
OR 08/26/2022
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
ASSEMBLE ITEMS AS SHOWN 2.

DIMENSIONS ARE IN MM
☺
ISOMETRIC VIEW
FOR REFERENCE ONLY
DO NOT SCALE
1
2
3
4
NEXT ASSEMBLY
5215500
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
A PRODUCTION RELEASE, DERIVED FROM 5215430 01/08/2018 TS 00903
B
ADDED 5530366, REPLACED 5715021 WITH
5715035, REMOVED GLUE NOTE, UPDATED BOM
REVISION
09/30/2019 TM 01128
C
REPLACED 5715035 WITH 5715049, 5530366
WITH 5530364, ADDED 5535357, UPDATED BOM
REVISION
07/29/2022 TM 01433
ITEM NO PART NUMBER DESCRIPTION QTY REV
1 5601218 P-9000/P-9000F L.H. TOP DECK WELDMENT 1 C
2 5715049 P9000 RAMP BOLT-ON RUBBER PAD 2 A
3 5530364 ELEVATOR BOLT M6 x 1.0 x 25 8 --
4 5535357 NUT M6 x 1.0 NL 8 --
WHERE USED
P9000LT
P9000LTF
SHEET 1 OF 1
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
C
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
NOTE: UNLESS OTHERWISE SPECIFIED .
TS
5215745
P9000LT L.H. TOP DECK
ASSEMBLY
01/08/2018
DO NOT SCALE DRAWING
1:8
SCALE:
THIRD ANGLE PROJECTION
OR 08/26/2022
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
SEE COLORS & GRAPHICS FOR LABEL PLACEMENT 2.
SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING 3.
ASSEMBLE ITEMS AS SHOWN 4.

DIMENSIONS ARE IN MM
☺
ISOMETRIC VIEW
FOR REFERENCE ONLY
DO NOT SCALE
5
4
8
7
6
2
1
3
ITEM
NO
PART
NUMBER
DESCRIPTION QTY REV
1 5601259 SHORT POWER UNIT CONSOLE WELDMENT, R.H. 1 A
2 5601260 SHORT POWER UNIT CONSOLE WELDMENT, L.H. 1 A
3 5215857 3-BUTTON 110/220V CONSOLE TOP 1 C
4 5737071 SHORT POWER UNIT CONSOLE DOOR 1 A
5 5601261 SHORT POWER UNIT CONSOLE DOOR WELDMENT, REAR 1 A
6 5715196 D2/XPR POLYETHYLENE COVER BLOCK 105 x 80 1 D
7 5520329 GROMMET GRO-1.25-UL CAPLUGS 2 -
8 5530031 HHB M6 x 1.0 x 12mm 16 -
NEXT ASSEMBLY
5260196
5260197
5260673
5260674
5260675
5260676
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
E ADDED 5905138 01/18/2021 CA 01212
F ADDED 5905775 08/18/2021 TM 01327
G
REPLACED LABELS WITH COLORS &
GRAPHICS NOTE, UPDATED BOM REVISION
09/21/2021 CA 01339
WHERE USED
P9000LT
P000LTF
MDS-6EXT
MDS-6EXTF
MDS-6LP
MDS-6LPF
SHEET 1 OF 1
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
G
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
NOTE: UNLESS OTHERWISE SPECIFIED .
TM
5215780
SHORT POWER UNIT
CONSOLE ASSEMBLY
05/01/2018
DO NOT SCALE DRAWING
1:12
SCALE:
THIRD ANGLE PROJECTION
OR 09/24/2021
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING 2.
SEE COLORS & GRAPHICS FOR LABEL PLACEMENT 3.

DIMENSIONS ARE IN MM
☺
1
2
4
6
3
5
7
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
A
PRODUCTION RELEASE, DERIVED FROM 5215780
AND 5215781
06/24/2019 TM 01096
B
ADDED 5545024, 5530304, 55535001, REPLACED
5701259 WITH 5601465, REMOVED 5525102,
5520052 AND 5525586
03/31/2020 TM 01152
C
REPLACED 5905039 WITH COLORS & GRAPHICS
NOTE
09/30/2021 CA 01350
ITEM
NO
PART
NUMBER
DESCRIPTION QTY REV
1 5601465 POWER UNIT CONSOLE COVER WELDMENT (3 BUTTON) 1 A
2 5590175 PUSH BUTTON AIR VALVE 1 --
3 5545024 WASHER, M3 x 9mm FLAT 2 --
4 5530043 SHCS M3 x 0.5 x 30 2 --
5 5535020 NUT M3 x 0.5, NL CL8 2 --
6 5550486 FTG NPL -02 NPT x -04 F NPT 1 --
7 5550087 FTG ELB -04 COMP x -02 NPT 1 --
WHERE USED
XR-12AE
SP-7XE SERIES
P9000LT SERIES
MDS-6 SERIES
NEXT ASSEMBLY
5215780
5215781
SHEET 1 OF 1
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
C
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
NOTE: UNLESS OTHERWISE SPECIFIED .
TM
5215857
3-BUTTON 110/220V
CONSOLE TOP
06/24/2019
DO NOT SCALE DRAWING
1:3
SCALE:
THIRD ANGLE PROJECTION
OR
10/07/2021
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
ASSEMBLE ITEMS AS SHOWN 2.
SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING 3.
SEE COLORS & GRAPHICS FOR LABEL PLACEMENT 4.

4270.0
3
1
2
ITEM NO PART NUMBER DESCRIPTION QTY REV
1 5570129 Ø6.4 ID HYDRAULIC HOSE 4216mm* -
2 5550325 FTG NPL Ø1/4 CRIMP x -04 JIC 1 -
3 5550345 FTG ELB Ø1/4 CRIMP x -04 JIC 1 -
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
B
UPDATED NEXT ASSEMBLY
UPDATED TITLE TO REFLECT NEXT ASSEMBLY
12/12/2008 AC 00256
OBSO REPLACED WITH 5570871 07/28/2009 AC 00249
C
UNOBSOLETED FOR USE IN PRODUCTION,
REPLACED 5570110 WITH 5570129, UPDATED
TITLE AND NEXT ASSEMBLY TO REFLECT WHERE
USED
06/29/2017 TM 00847
D
UPDATED TITLE TO REFLECT WHERE USED,
UPDATED NEXT ASSEMBLY
05/08/2018 TM 00903
NEXT ASSEMBLY
5250034
5250110
5250174
WHERE USED
P9000LT SERIES
SP-7XE SERIES
SHEET 1 OF 1
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
D
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
AC
5570040
HYDRAULIC HOSE
ASSEMBLY Ø6.35 x
4270mm SB
01/11/2008
DO NOT SCALE DRAWING
1:2
SCALE:
THIRD ANGLE PROJECTION
CA 05/23/2018
DIMENSIONS ARE IN MM
TOLERANCES:
0. = ±1.5
0.0 = ±1.0
0.00 = ±0.25
0.000 = ±0.13
SURFACE FINISH 1.6 ISO Ra µm
FOR MACHINED SURFACES
UNLESS OTHERWISE SPECIFIED
NOTE: UNLESS OTHERWISE SPECIFIED.
FOR ITEM 1 SPECIFICATIONS REFER TO PART SPECIFICATION FORM 1.
(*)ITEM 1 QTY FOR REFERENCE ONLY 2.

PART SPECIFICATION FORM
ACP
BENDPAK Number:
5570129
MRP Description:
¼” HYDRAULIC HOSE 31 CL-0400X
Date:
05/24/2018
ECO :
00950
1. Engineering Specification
Application:
¼” HYDRAULIC HOSE
Detailed Description:
ONE or TWO BRAID STEEL WIRE HYDRAULIC HOSE
SIZE: 1/4” / 6mm I.D. MIN
0.53” / 13.4mm O.D. MAX
SPECS: 5700PSI OR 393 BAR WORKING PRESSURE MINIMUM
17100PSI OR 1179 BAR MINIMUM BURST PRESSURE MINIMUM
3” / 80mm MIN BEND RADIUS
COLOR: BLACK
ADDITIONAL CONTACT INFORMATION:
Xin Yurong
Shandong Ningjin High Energy Hose Co., Ltd.
Tel: [phone]
No. 7, Taishan Rd., Industrial Park, Ningjin County, Shandong, China
Approved Vendor
Vendor Part #
Contact #
AUTHORIZED
COMPONENT PROVIDER
1) Ningjin Hydraulic Hose
Co.
5570129
[phone]
X
2)
OR BENDPAK ENGINEERING APPROVED EQUIVALENT
2. Vendor Information (Or for Reference)

ISOMETRIC VIEW
FOR REFERENCE ONLY
DO NOT SCALE
2
1
3
4
ITEM NO PART NUMBER DESCRIPTION QTY REV
1 5731041 P9000 SAFETY LOCKOUT BAR, L.H. 1 D
2 5530332 FHS M8 x 1.25 x 25 2 -
3 5746092 P-6B/9000 SERIES SAFETY RELEASE BUNG 1 B
4 5601051-1 SAFETY BAR EXTENSION 1 -
WHERE USED
P9000 SERIES
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
B UPDATED BOM REVISION 11/01/2016 TS 00781
C
C-001
WAS 17 NOW 23, REPLACED 5530002 WITH
5530332, UPDATED PAINT & BOM REVISION
ADDED 20% GLOSS PAINT NOTE
07/20/2017
04/17/2020
TM
CA
00852
01161
D
ADDED 5601051-1, 5746092 DISTANCE WAS 23
NOW 44, WAS 105 NOW 80, UPDATED BOM
REVISION
08/23/2022 TM 01433
NEXT ASSEMBLY
5215500
SHEET 1 OF 2
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
D
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
TM
5601051
P9000 SAFETY LOCKOUT
BAR WELDMENT, LH
11/10/2015
DO NOT SCALE DRAWING
1:3
SCALE:
THIRD ANGLE PROJECTION
OR 08/25/2022
DIMENSIONS ARE IN MM
TOLERANCES:
0. = ±1.5
0.0 = ±0.5
SURFACE FINISH 1.6 ISO Ra µm
FOR MACHINED SURFACES
UNLESS OTHERWISE SPECIFIED
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
BREAK AND DEBURR ALL SHARP EDGES 0.3mm 2.
REMOVE ALL WELD SPLATTER 3.
DIMENSIONS SHOWN ARE AFTER PAINTING 4.
PAINT GRAY (RAL-7024) 20% GLOSS 5.
THREADS MUST BE CLEAN AND FREE OF ALL WELD 6.
SPLATTER AND PAINT
NOTE: UNLESS OTHERWISE SPECIFIED.

ISOMETRIC VIEW
FOR REFERENCE ONLY
DO NOT SCALE
2
1
3
4
ITEM NO. PART NUMBER DESCRIPTION QTY. REV
1 5731042 P9000 SAFETY LOCKOUT BAR, R.H. 1 D
2 5530332 FHS M8 x 1.25 x 25 2 -
3 5746092 P-6B/9000 SERIES SAFETY RELEASE BUNG 1 B
4 5601052-1 SAFETY BAR EXTENSION 1 --
WHERE USED
P9000 SERIES
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
B UPDATED BOM REVISION 10/28/2016 TS 00781
C
C-001
WAS 17 NOW 23, REPLACED 5530002 WITH
5530332, UPDATED PAINT COLOR AND BOM
REVISION
ADDED 20% GLOSS PAINT NOTE
07/20/2017
04/17/2020
TM
CA
00852
01161
D
ADDED 5601052-1, 5746092 DISTANCE WAS 23
NOW 44, WAS 105 NOW 80, UPDATED BOM
REVISION
08/23/2022 TM 01433
NEXT ASSEMBLY
5215498
SHEET 1 OF 2
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
D
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
TM
5601052
P9000 SAFETY LOCKOUT
BAR WELDMENT, RH
11/10/2015
DO NOT SCALE DRAWING
1:3
SCALE:
THIRD ANGLE PROJECTION
OR 08/25/2022
DIMENSIONS ARE IN MM
TOLERANCES:
0. = ±1.5
0.0 = ±0.5
SURFACE FINISH 1.6 ISO Ra µm
FOR MACHINED SURFACES
UNLESS OTHERWISE SPECIFIED
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
BREAK AND DEBURR ALL SHARP EDGES 0.3mm 2.
REMOVE ALL WELD SPLATTER 3.
DIMENSIONS SHOWN ARE AFTER PAINTING 4.
PAINT GRAY (RAL-7024) 20% GLOSS 5.
THREADS MUST BE CLEAN AND FREE OF ALL WELD 6.
SPLATTER AND PAINT
NOTE: UNLESS OTHERWISE SPECIFIED.

ISOMETRIC VIEW
FOR REFERENCE ONLY
DO NOT SCALE
5
3
4
6
1
2
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
A PRODUCTION RELEASE, DERIVED FROM 5600899 01/08/2018 TS 00903
B
ADDED 5737142, ADDED CRITICAL DIMENSIONS
AND MODEL REFERNCE NOTE
09/26/2019 TM 01128
C REMOVED 5737142, UPDATED BOM REVISION 07/29/2022 TM 01433
NEXT ASSEMBLY
5215499
ITEM NO PART NUMBER DESCRIPTION QTY REV
1 5701249 P-9000/P-9000F TOP DECK/COVER 1 B
2 5737041 P-9000/P-9000F BASE PIVOT PLATE 8 A
3 5735028 PIN STOP 1 B
4 5736927 UPPER CLEVIS MOUNT 3 A
5 5735639 P9000 LT SERIES TOP DECK RIENFORCING BAR 1 A
6 5737072 P9000LT RAMP SPACER 2 A
WHERE USED
P9000LT
P9000LTF
SHEET 1 OF 3
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
C
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
TS
5601217
P9000LT R.H. TOP DECK
WELDMENT
01/08/2018
DO NOT SCALE DRAWING
1:10
SCALE:
THIRD ANGLE PROJECTION
OR 08/25/2022
DIMENSIONS ARE IN MM
TOLERANCES:
0. = ±1.5
0.0 = ±0.5
SURFACE FINISH 1.6 ISO Ra µm
FOR MACHINED SURFACES
UNLESS OTHERWISE SPECIFIED
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
BREAK AND DEBURR ALL SHARP EDGES 0.3mm 2.
REMOVE ALL WELD SPLATTER 3.
NOTE: UNLESS OTHERWISE SPECIFIED.

ISOMETRIC VIEW
FOR REFERENCE ONLY
DO NOT SCALE
4
3
6
1
2
5
NEXT ASSEMBLY
5215745
ITEM NO PART NUMBER DESCRIPTION QTY REV
1 5701255 P-9000/P-9000F TOP DECK/COVER 1 A
2 5737041 P-9000/P-9000F BASE PIVOT PLATE 8 A
3 5736927 UPPER CLEVIS MOUNT 3 A
4 5735028 PIN STOP 1 B
5 5735639 P9000 LT SERIES TOP DECK RIENFORCING BAR 1 A
6 5737072 P9000LT RAMP SPACER 2 A
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
A PRODUCTION RELEASE, DERIVED FROM 5600898 01/08/2018 TS 00903
B
ADDED 5737142, ADDED CRITICAL DIMENSIONS
AND MODEL REFERENCE NOTE
09/30/2019 TM 01128
C REMOVED 5737142, UPDATED BOM REVISION 07/29/2022 TM 01433
WHERE USED
P9000LT
P9000LTF
SHEET 1 OF 3
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
C
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
TS
5601218
P9000LT L.H TOP DECK
WELDMENT
01/08/2018
DO NOT SCALE DRAWING
1:10
SCALE:
THIRD ANGLE PROJECTION
OR 08/25/2022
DIMENSIONS ARE IN MM
TOLERANCES:
0. = ±1.5
0.0 = ±0.5
SURFACE FINISH 1.6 ISO Ra µm
FOR MACHINED SURFACES
UNLESS OTHERWISE SPECIFIED
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
BREAK AND DEBURR ALL SHARP EDGES 0.3mm 2.
REMOVE ALL WELD SPLATTER 3.
NOTE: UNLESS OTHERWISE SPECIFIED.

3
1
2
ISOMETRIC VIEW
FOR REFERENCE ONLY
DO NOT SCALE
WHERE USED
P9000 SERIES
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
A
A-001
PRODUCTION RELEASE, DERIVED FROM 5620286
ADDED 20% GLOSS PAINT NOTE
01/05/2018
04/17/2020
TS
CA
00903
01161
ITEM NO. PART NUMBER DESCRIPTION QTY. REV
1 5735638 P9000 LT SERIES ARM PLATE 2 A
2 5620612
P9000LT SERIES ASYMMETRIC HINGE ARM
WELDMENT
2 A
3 5735642 P9000 LT SERIES SMALL ARM PLATE 1 A
NEXT ASSEMBLY
5215498
5215500
SHEET 1 OF 2
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
A
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
TS
5620613
P9000LT SERIES ASYMMETRIC
HINGE DOUBLE ARM
WELDMENT
11/08/2017
DO NOT SCALE DRAWING
1:8
SCALE:
THIRD ANGLE PROJECTION
OR 04/23/2020
DIMENSIONS ARE IN MM
TOLERANCES:
0. = ±1.5
0.0 = ±0.5
SURFACE FINISH 1.6 ISO Ra µm
FOR MACHINED SURFACES
UNLESS OTHERWISE SPECIFIED
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
BREAK AND DEBURR ALL SHARP EDGES 0.3mm 2.
REMOVE ALL WELD SPLATTER 3.
DIMENSIONS SHOWN ARE AFTER PAINTING 4.
PAINT BENDPAK GRAY (RAL-7024) 20% GLOSS 5.
NOTE: UNLESS OTHERWISE SPECIFIED.

PART SPECIFICATION FORM (STANDARD)
BENDPAK Number:
5900022
MRP Description:
P9000LT INSTALLATION AND OPERATION MANUAL
Date:
08/19/2022
ECO :
---
1. Engineering Specification
Application:
INSTALLATION MANUAL
Detailed Description:
Print Settings
Unless otherwise specified, use these settings for
printing BendPak manuals:
Size:
A4 (210 to 297 mm), 8.5 by 11
inches (216 to 279 mm), or between
Color:
Black and White
Binding:
Saddle Stitched
Paper:
100 to 120 gsm (27 to 32 pound),
uncoated
2. Vendor Information (Or for Reference)
ApprovedVendor
Vendor Part #
Contact #
PreferredVendor
1)
OR BENDPAK ENGINEERING APPROVED EQUIVALENT