Better Bathrooms Morella 80 User manual

•Multi-person assembly
•We always recommend using professional tradespeople
to install your product
V1_14.12.2020
•
Product Code –BeBa_27210 - BeBa_27211
Morella 80 Vanity Cabinet - Matt Black

Congratulations on your purchase
And welcome to our growing gang of savvy shoppers
We're on a mission to bring you extraordinary bathroom products, for less. From
modern to traditional style ceramics, plus the gorgeous fixtures, fittings and furniture
to match. So, you can fall in love with your space every single day.
As one of the UK's largest independent bathroom stores, we've received countless
awards; including the National Business Awards UK, the Digital Entrepreneur Awards
and being placed on The Sunday Times Fast Track 100.
We hope your new product exceeds your highest expectations. However, if you
experience any problems, please:
•call our friendly UK call centre on 03303903062 (9am-7pm Monday to Friday,
or 10am-4pm Saturday and Sunday), or
•send us a message via [e-mail]
Important information
•Please read these instructions thoroughly and retain for future reference
•Please ensure the product is installed level on all 4 plains
•Tap flow rate should be reduced to suit the basin, allowing the tap to be turned
on fully without over splashing of the basin
•Use cut out screw holes if provided to fix the furniture to the wall
•Please inspect the product fully for any damage or defects prior to installation
•Ensure the correct waste is installed and is water tight, periodically check the
installation for leaks
•The tap in the photo does not belong to the purchased product. It is sold
separately. It is used for visual purposes only.
•Always check all wall before drilling to prevent damage to pipes and
cables.
•
UnitWeight(Kg) BasinWeight (Kg) Max. Loading Weight (Kg)
29,00 21,60 71,00

PARTS / DIAGRAMS
A –RIGHT SIDE PANEL
DRAWER INC.
DRAWER RUNNERS X2
A
F
B
C
P
D
E
G
I
J
H
G
H
K
L
L
M
N
O
B –LEFT SIDE PANEL
DRAWER INC.
DRAWER RUNNERS X2
C –BACK SUPPORT PANEL
D –FRONT SUPPORT PANEL
E –BOTTOM PANEL
F –TOP SUPPORT PANEL
G –RIGHT DRAWER SIDE
H –LEFT DRAWER SIDE
I –
BASE DRAWER INNER PANEL
J –LOWER DRAWER FRONT
K –UPPER DRAWER FRONT
L –BACK DRAWER PANEL
M –
TOP DRAWER BOTTOM PANEL
N –LONG SEPERATOR X2
O –SHORT SEPERATOR X2
P –SIPHON INSTALLATION GAP

Tools required
Troubleshooting
Drawer not straight / not closing
See drawer adjustment guide above
Leaking
Check sealant, reapply if necessary

Installation
Please spend 5 minutes reading this section before commencing with the installation of your
new furniture
1. Should any of your items have a defect, please do not install as returns will not be accept once fitted.
2. We advise that you use a qualified person to install your units, as any issues relating to poor fitting will not
be accepted by the supplier.
3. This product is water resistant but NOT waterproof and therefore the room must be well ventilated and any
standing water must be wiped dry after use.
4. Please avoid direct sunlight as this will cause the painted surfaces to discolour.
5. Due to motion in transit, the cabinet doors and drawers may need to be adjusted after installation
6. Floor standing units must be secured back to the wall through the back rail using suitable fixings.
7. Basins units should be fitted as above, and then the basin should also be secured where applicable, using
Fischer bolts not supplied) though the fixing points under the basin and/or siliconed between the basin and
unit.
8. Fixings and wall type must be sufficient to support the unit, the fixings supplied are for solid wall fixing.

İnfo :
1- Place the wall hanging brackets against the
wall and mark the drill holes, so that they are
aligned with the measurements of the unit
and are level.
2- To do this use a tape measure and spirit level.

İnfo :
1- Drill the holes into the wall at 7 mm diameter and to a depth of
100 mm.
2- Apply a small amount of silicone into the hole.
3- Insert the dowels(Wall plugs) into the holes and tap flush to the
wall surface using a hammer.

İnfo :
Secure the hangers to the wall using the screws
provided.

Drawer Removal
Drawer Adjustment
1
3
2
1
2
1- Pull the drawer to yourself.
2- Pull the drawer to outside by
pressing the latch locks at the
same time.
3- Lift the drawer up and out of the
unit.
4- Proceed in the same way for the
each drawers.
1- Adjust the drawer height by
turning the dials on the
underside of the drawer.
2- Adjust the drawer centrally by
turning the dials on the bottom
of the drawer.

Maintenance
Please note that although these units have been designed to give years of pleasure and satisfaction, you will help maintain the original
beauty of your bathroom by following these guidelines.
Melamine, vinyl and foil wrapped doors
Occasional marks, can in most cases, be removed with a soft damp cloth. More persistent marks can be
removed using a non-silicone-based furniture cleaner. Hot soapy water should be avoided. Once the mark is
removed, the area should be wiped over with a damp cloth to remove any excess and dried with a soft clean
cloth. On no account should solvent or an abrasive cleaner be used as permanent damage to the finish could
take place.
High Gloss Doors
Use a cleaning product not containing aggressive substances like acetone, alcohol, bleach etc. as those
components could seriously damage the surface of the door. The best would be to use a soft cotton or micro
fibre cloth with only water and a soft soap (containing a maximum 1% of liquid soap)
Carcass components
Do not use polish on any surfaces. A damp cloth with soapy water will clean off most marks or spills. On no
account should any spillage, even water, be allowed to lie of the surface. Bleaches scouring pads and multi-
surface cleaners should not be used.
Drawers, runners, door hinges.
These should be wiped out with a damp soapy cloth and wiped dry with a soft cloth as necessary. The roller
runners and hinges are lubricated and should not be cleaned with a degreasing agent as this will affect the
action of the moving parts. Never lean on partially or fully opened doors and drawers in order to gain access to
the units. The hinges are specified to adequately support the weight of the door, plus small additional weights
such as wire accessories. It is advised that once the bathroom has been installed, you should check every six
months that all screws on the hinges are tight.
Worktops
Although the worktop is hard wearing, sharp objects will scratch and excessive heat will scorch the surface.
Care should be taken not to drop any heavy objects onto the worktop as the surface may crack. For cleaning, a
damp soapy cloth with clean off most spills. Bleaches, scouring pads and multi-surface cleaners should not be
used. Corrosive liquids and make-up should be wiped off immediately. On no account should any spillage, even
water, be allowed to lie on the surface.
Temperature, humidity, ventilation and proximity
Avoid excessive change in temperature and humidity. We would advise an extractor fan to be installed in all
bathrooms which include furniture to reduce the chance of water ingress damage. The extractor fan should be
used every time that the shower/bath is used and should be left switched on for a sufficient time afterward to
allow for adequate ventilation. Ensure that the fan has been correctly sized for the room in use. The units,
under no circumstance, should be fitted in a location where they are regularly subjected to contact with water.
Cleaning
To maintain the surface of your product, wipe with a clean damp cloth and wipe dry,
do not use any abrasive cleaning agents or materials. If any harsh chemicals come
into contact with the surface of the product, rinse and wipe clean immediately.