Better Bathrooms BeBa 27584 User manual

1
LED BATHROOM MIRROR WITH
DEMISTER
BeBa_27584 BeBa_27585
•TOUCH CONTROL
•BLUETOOTH CONNECTIVITY
•IP44 INGRESS PROTECTION

2
CONGRATULATIONS ON YOUR PURCHASE
Our aim at Better Bathrooms is to bring you extraordinary bathroom products, for less.
If you’re after a modern, traditional, or a totally unique style bathroom, we have the fittings
and fixtures to bring your ideas to life, so you can fall in love with your space every day.
We hope your new product goes above and beyond your expectations. However, should
any problems occur, please:
•Log in to your account and contact our customer services team via your self-service
portal –betterbathrooms.com/CustomerAccount/Login
•Contact us via betterbathrooms.com/contact/contact-us
CONTENTS
SAFETY
3
BATHROOM ZONES
4
PARTS SUPPLIED
5
TOOLS REQUIRED
5
INSTALLING THE MIRROR
6
OPERATION
7
TECHNICAL SPECIFICATIONS
8

3
SAFETY
•This mirror should be installed by a qualified electrician.
•This fitting is only suitable for connection to a 220-240V earthed supply
in accordance with current IEE wiring regulations, and should be
installed in accordance with local Building Regulations.
•This is for domestic, indoor use only.
•The fitting should be connected to a dedicated lighting circuit which
must be protected by a 5-amp fuse (or a 6-amp miniature circuit
breaker).
•Before installing the fitting ensure the mains supply is switched off, and
that the appropriate fuse is removed (or appropriate circuit breaker is
switched off) before commencing installation. Ensure that measures
are taken to prevent the supply from being inadvertently reconnected.
•If there is a “Minimum Distance” Label, please do not allow Flammable
Materials to rest within that distance from the unit.
•This product may contain delicate parts –be careful during handling
and maintenance to avoid breakage.
•If any modification is made to the fitting it will invalidate the warranty
and may render the product unsafe.
•A defective appliance may cause electric shock. Never switch on a
defective or damaged appliance. Disconnect the appliance from the
mains before seeking assistance.
•This product is IP44 rated, and no part of the installation is allowed to
be within bathroom Zones 0 or 1. Installation is permitted within Zone
2.
•This product must be earthed. Before commencing installation, ensure
that there are no pipes or wires located behind the wall that may be
damaged during drilling.
•Ensure that the hanging location has been decided upon and marked
clearly to avoid unwanted damage in the wall due to incorrect
positioning.
•Check that the mirror is not damaged prior to installation.
•Take care unpacking, do not use a sharp blade to open as this may
damage the mirror and void your warranty.
•Installation must only be carried out by a qualified professional or
electrician.

4
BATHROOM ZONES
Zone 0:
The interior of the bathtub or shower basin.
Zone 1:
The area around the bathtub or shower basin up
to a height of 2.25m above the floor
Zone 2:
The area stretching to 0.6m outside the bath or
shower and above the bath or shower if over
2.25m

5
PARTS SUPPLIED
WALL PLUGS (X4)
SCREWS M4 (X4)
PLEASE NOTE: It is the installers responsibility to ensure that the fittings are suitable for the type of wall.
Alternative fittings may be required (Not Supplied). If unsure professional advice should be sought.
TOOLS REQUIRED tool
TAPE MEASURE
SPIRIT LEVEL
ELECTRIC DRILL
SCREWDRIVER
HAMMER
8mm DRILL BIT
PENCIL

6
HANGING THE MIRROR
The mirror comes with the option of hanging both in landscape or portrait
orientation. At the back of the mirror, there are 4 key holes 2 on the vertical side
and 2 the horizontal side.
To hang the mirror, you will need to drill two holes into the wall, ensuring that
there are no wires or pipes behind the wall before commencing.
1. Ensure that the power is disconnected at the circuit
breaker, and that there is no risk of reconnection during
installation.
2. Measure the distance between the two key holes.
3. Make a note of the distance and mark their position on the
wall. Use a spirit level to ensure that the holes are level.
4. Drill the 2 holes into the wall at the position marked using
a suitable drill bit.
5. Insert the wall plugs into the holes.
6. Insert the screws into the wall plugs, ensuring their heads
are protruding by approximately 3mm.
7. Check to ensure the screws line up correctly and the mirror
can be safely hung from them.
8. The mirror should now be connected to a suitable fuse
spur following current regulations and guidance. When
connecting ensure that enough cable is left to allow the
mirror to be safely removed.
9. You will now be able to hang the mirror. Carefully lower
the mirror onto the screws, ensuring that is secure and will
not slide.
10. Reconnect the power supply.

7
OPERATION
Press the button once to turn on the lights and to begin
de-misting.
Hold the button to change the colour temperature from
3000K (Warm White) to 6000K (Cool White).
Press again to turn the lights and demister off.
BLUETOOTH PAIRING
To pair your phone to the Bluetooth speaker system,
press the Bluetooth symbol to start pairing.
Access your phones Bluetooth connection option via
your settings and a list of devices will be shown.
Locate “Mirror-BT” and select it.
Your phone will now be paired to the speakers. To
exit pairing, you can disconnect using your phone, or
press the Bluetooth button on your mirror.
SHAVER SOCKET
Your mirror comes with a shaver socket. This socket is
only designed for use with shavers and other low
voltage items designed to be powered from a shaver
socket.
Once the mirror is connected to the mains, the shaver
socket should be ready to use.

8
TECHNICAL SPECIFICATION
Model
BeBa_27584
BeBa_27585
WxHxD (mm)
600x800x55
1200x600x55
Net Weight (Kg)
7.2
10.0
Power Cord length
(cm)
56
100
Rated Power (W)
41W
60W
IP Rating
IP 44
IP 44
Input
220 V-240 V 50 Hz
220 V-240 V 50 Hz
This product contains a light source of energy efficiency class F.
DISPOSAL
Recycling facilities are now available for all customers at which you can
deposit your old electrical products. Customers will be able to take any old
electrical equipment to participating sites run by their local councils.
Please remember that this equipment will be further handled during the
recycling process, so please be considerate when depositing your
equipment. Please contact the local council for details of your local
household waste recycling centers.
At the time of printing the product contains no substances listed within Annex XIV of the
Reach Regulations (EC) 1907/2006. In accordance with Article 59 of the same regulation the
following substances are contained within the product at permitted levels: Cadmium.
As a responsible manufacturer the regulations are monitored to ensure continued
compliance. Further information can be provided upon request.

9