Better Bathrooms BeBa 26153 User manual

1
WALL MOUNTED LED MIRRORED
CABINET WITH SHAVER SOCKET
AND DEMISTER
BeBa_26153
•INFARED SENSOR CONTROL
•ADJUSTABLE STAINLESS-STEEL BUFFER HINGE
•IP44 INGRESS PROTECTION
•ALUMINIUM ALLOY CABINET

2
CONGRATULATIONS ON YOUR PURCHASE
Our aim at Better Bathrooms is to bring you extraordinary bathroom products, for less.
If you’re after a modern, traditional, or a totally unique style bathroom, we have the fittings
and fixtures to bring your ideas to life, so you can fall in love with your space every day.
We hope you’re happy with your new product. But if you experience any problems, we’re
always here to help.
•Call our friendly UK call centre on 0330 390 3062
(Lines open 9am-4.30pm Monday to Friday, or 9am-2pm Saturday).
•Send us a message via betterbathrooms.com.
CONTENTS
SAFETY
3
BATHROOM ZONES
4
PARTS SUPPLIED
5
TOOLS REQUIRED
5
INSTALLING THE CABINET
6
DOOR ADJUSTMENT
7
SHELF ADJUSTMENT
7
OPERATION
8
CLEANING AND MAINTENANCE
8
TECHNICAL SPECIFICATIONS
9

3
SAFETY
•This cabinet should be installed by a qualified electrician.
•This fitting is only suitable for connection to a 220-240V earthed supply in accordance
with current IEE wiring regulations, and should be installed in accordance with local
Building Regulations.
•This is for domestic, indoor use only.
•The cabinet should be connected to a dedicated lighting circuit which must be protected
by a 5-amp fuse (or a 6 amp miniature circuit breaker).
•The electrical connection must be an adequate distance from the rear of the cabinet to
prevent the risk of shorting with the cabinet’s casing.
•Before installing the fitting ensure that the mains supply is switched off, and that the
appropriate fuse is removed (or appropriate circuit breaker is switched off) before
commencing installation. Ensure that measures are taken to prevent the supply from
being inadvertently reconnected.
•If there is a “Minimum Distance” label, please do not allow flammable materials to rest
within that distance from the unit.
•This product may contain delicate parts –be careful during handling and maintenance to
avoid breakage.
•Ensure the cover for the shaver socket is closed when not in use to prevent moisture
from entering it.
•Only connect items designed to be used with a shaver socket (Such as shavers or electric
toothbrushes).
•The shaver socket is not earthed and provides 230V at a maximum current of 80mA. Do
not connect devices which require a higher current, different voltage, or an earth
connection.
•If any modification is made to the fitting it will invalidate the warranty and may render
the product unsafe.
•A defective appliance may cause electric shock. Never switch on a defective or damaged
appliance. Disconnect the appliance from the mains before seeking assistance.
•This product is IP44 rated, and no part of the installation is allowed to be within
bathroom Zones 0 or 1. Installation is permitted within Zone 2.
•This product must be earthed. Before commencing installation, ensure that there are no
pipes or wires located behind the wall that may be damaged during drilling.
•Ensure that the hanging location has been decided upon and marked clearly to avoid
unwanted damage to the wall due to incorrect positioning.
•Inspect the cabinet to ensure there are no signs of damage prior to installation.
•Take care unpacking, do not use a sharp blade to open as this may damage the product
and void your warranty.
•Once installed a bead of silicon can be applied between the cabinet and the wall across
the top and sides of the unit. Never seal the bottom of the cabinet to the wall, as this
may allow water to accumulate behind the unit.
•Ensure that the infrared sensor will be easily accessible following installation and that at
least 20cm of space is left around the sensor to ensure correct operation.

4
BATHROOM ZONES
Zone 0:
The interior of the bathtub or shower basin.
Zone 1:
The area around the bathtub or shower basin up
to a height of 2.25m above the floor
Zone 2:
The area stretching to 0.6m outside the bath or
shower and above the bath or shower if over
2.25m

5
PARTS SUPPLIED
WALL PLUGS (X4)
SCREWS M4 (X4)
ALUMINIUM BAR (X1)
PLEASE NOTE: It is the installers responsibility to ensure that the fittings are suitable for the type of wall.
Alternative fittings may be required (Not Supplied). If unsure professional advice should be sought.
TOOLS REQUIRED tool
TAPE MEASURE
SPIRIT LEVEL
ELECTRIC DRILL
SCREWDRIVER
HAMMER
8mm DRILL BIT
PENCIL

6
INSTALLATION
The cabinet is supplied with a hanging bar to mount the cabinet onto the wall. At
the back of the cabinet there is a corresponding bar which is designed to slot onto
the hanging bar.
1. Choose the desired position of the cabinet, and from that determine the
required position of the hanging bar.
2. Hold the hanging bar in position, using a spirit level to ensure it is level.
3. Use a pencil to mark the position of the 3 holes on the wall.
4. Place the hanging bar to one side, and drill the holes with a suitable drill bit.
5. Insert wall plugs into the holes, ensuring they are flush to the wall.
6. Place the hanging bar onto the wall, lining up the 3 holes with the wall plugs.
7. Secure the hanging bar to the wall using the supplied screws.
8. You will now be able to hang the cabinet. Carefully lower the cabinet onto the
hanging bar, ensuring that is secure and will not slide.
9. Open the cabinet door and mark the wall with a pencil through the security
hole on the back panel.
10. Remove the cabinet, drill the hole then place a wall plug into the hole you
have just drilled.
11. Hang your cabinet back up onto the hanging bar and ensure that the in the
cabinet is lined up with the wall plug.
12. The cabinet should now be connected to a suitable fused spur following
current regulations and guidance. We would advise for this to be situated
directly behind the cabinet below the hanging bar. When connecting ensure
that enough cable is left to allow the cabinet to be safely removed from the
hanging bar.
13. Secure the cabinet to the wall using a screw through the security hole and
into the wall plug you previously installed.

7
DOOR ADJUSTMENT
If the door is not level, you can
adjust it using the hinge screw.
Turning the screw clockwise
will push the door right, and
turning anticlockwise will pull it
right.
SHELF ADJUSTMENT
Loosen the snap screw on the shelf to adjust
the shelf position.
Once the shelf is in the correct position and
level the screw should then be re tightened.

8
OPERATION
Your mirror comes with an infrared sensor located on the
right-hand side. To activate the light and the demister, move
your hand across the sensor once at a distance of around
5cm.
To turn the light and demister off, move your hand across
the sensor again.
SHAVER SOCKET
Your mirror comes with an inbuilt shaver socket
located on the inside of the mirror above the top
shelf. This socket is only designed for use with
shavers.
Once the mirror is connected to the mains, the shaver
socket should be ready to use. Do not leave shavers
plugged in when unattended and ensure that the
socket cover is in place when not in use.
CLEANING AND MAINTENANCE
Never use products containing bleach or abrasive cleaners, as these will have a
detrimental effect on the appearance and lifespan of the product.
Use a clean micro fiber cloth to clean the mirror.

9
DISPOSAL
Recycling facilities are now available for all customers at which you can
deposit your old electrical products. Customers will be able to take any old
electrical equipment to participating sites run by their local councils.
Please remember that this equipment will be further handled during the
recycling process, so please be considerate when depositing your
equipment. Please contact the local council for details of your local
household waste recycling centers.
At the time of printing the product contains no substances listed within Annex XIV of the
Reach Regulations (EC) 1907/2006. In accordance with Article 59 of the same regulation the
following substances are contained within the product at permitted levels: Cadmium.
As a responsible manufacturer the regulations are monitored to ensure continued
compliance. Further information can be provided upon request.
TECHNICAL SPECIFICATION
Model
BeBa_26153
WxHxD (mm)
500x700x130
Net Weight (Kg)
13.5
Power Cord length (cm)
50
Rated Power (W)
25
IP Rating
IP44
Input
220 - 240V, 50 Hz
Shaver Socket Output
230V, 50Hz, 80mA
This product contains a light source of energy efficiency class F.
V20211214