Better Bathrooms Arissa ARIMB005 User manual

Product
ARIMB005 - Arissa Matt Black Deck Mounted Bath Filler Tap
ARIBB005 - Arissa Brushed Brass Deck Mounted Bath Filler Tap
ARICH005 - Arissa Chrome Deck Mounted Bath Filler Tap
ARIMB006 - Arissa Matt Black Deck Mounted Bath hower Mixer Tap
ARIBB006 - Arissa Brushed Brass Deck Mounted Bath hower Mixer Tap
Single-person assembly
Tools required
We always recommend using professional
tradespeople to install your product
V2_3/ /2022

Congratulations on your purchase
And welcome to our growing gang of savvy shoppers
We're on a mission to bring you extraordinary bathroom products, for less. From modern
to traditional style ceramics, plus the gorgeous fixtures, fittings and furniture to match. o,
you can fall in love with your space every single day.
As one of the UK's largest independent bathroom stores, we've received countless
awards; including the National Business Awards UK, the Digital Entrepreneur Awards and
being placed on The unday Times Fast Track 100.
We hope your new product goes above and beyond your expectations. However, should
any problems occur, please:
log in to your account and contact our customer services team via your self-serve
portal – betterbathrooms.com/CustomerAccount/Login
contact us via betterbathrooms.com/content/contact-us
Important information
Please read these instructions thoroughly and retain for future reference
Installation must be carried out in compliance with The Water Fittings Regulations
and cottish Water Byelaws.
The system must be flushed prior to installation
Minimum and Maximum working pressure : 1 - 5 bar
Pressures must be equal for optimum performance
Please do not connect hot and cold water supply lines in reverse. This could result
in hot water flowing from cold line and cause scalding.
The feed-water temperature of water shall not exceed 85°C.
Exceeding 85°may cause scalding, the service life of faucets might be shortened,
or the faucet might be damaged.
After installation, please make sure the faucet is securely mounted and checked for
leaks.

Parts / Diagrams
N
o
Description
1 Handle
assembled(hot)
2 Handle
assembled(cold)
3 Headwork hot
supply
4 Headwork cold
supply
5 Body
6 Washer
7 Aerator
8 Housing
9 Base
10 Washer
11 Leg assembled
12 Washer
13 Locknut
No Description No Description
1 Handle
assembled(hot)
11 Base
2 Handle
assembled(cold
)
12 Washer
3 witch handle 13 Leg assembled
4 Headwork hot
supply
14 Washer
5 Headwork cold
supply
15 Locknut
6 Body 16 hower hose
7 Divertor 17 hower holder
8 Washer 18 Wall Plug & elf-
tapping screw
9 Aerator 19 Handshower

10 Housing
Dimensions
Tools required
Drill
panner
Installation
Remove the rubber gaskets(6D) and locknuts(6E)
from the Legs.
From above, push the legs through holes on
bathtub;
From underneath the bathtub, secure the mixer by
fixing the rubber gaskets(6D) and locknuts(6E) onto
the legs. Fasten the locknuts(6E).

Refer to the installation hole dimension on the
shower holder to drill two holes vertically on the wall
surface.
Drive the wall plugs into the hole. Install the fixing
screws onto the shower holder.
Place the shower holder on the wall surface being
drilled beforehand and then fasten with the fixing
screws.(Pay attention to ensure that the direction is
correct.)
Connect the shower hose with the mixer body and
hand shower. Pay attention that rubber washers
should be contained in the nuts of the hose.
Connect the hot and cold flexible hoses(not included
to the isolation valves(not included), hot on the left,
cold on the right.
Turn on water supply and check for leaks.
Operation

Troubleshooting
Issues Inspection Item
Poor water flow Deck-mounted bath filler tap:
 Is there blockage within the filter mesh on
aerator(7)
Was the system flushed prior to installation
Is the headwork(3,4) free from debris
Deck-mounted bath shower mixer tap:
 Is there blockage within the filter mesh on
aerator(9)
Was the system flushed prior to installation
Is the headwork(4,5) free from debris
Water leak Deck-mounted bath filler tap:
Is there damage or dirt within the O-rings of the
headworks(3,4)
Is the headwork fully tighten by wrench(3,4)
Is there damage or dirt with the rubber
washer(6) in the of aerator
Is the aerator housing(8) fully tightened
Is there damage within the rubber
washer(10)under the base
Is there damage with the O-rings on the legs(11)
Deck-mounted bath shower mixer tap:
Is there damage or dirt within the O-rings of the
headworks(4,5)
Is the headwork fully tighten by wrench(4,5)
Is there damage or dirt with the rubber
washer(8) in the of aerator
Is the aerator housing(10) fully tightened
Is there damage within the rubber
washer(12)under the base
Is there damage with the O-rings on the legs(13)
Is there damage with the O-rings on divertor(7)
Is there damage within the rubber washer inside
the nuts of shower hose(16)
Handle loose Is the screw inside the handle(1,2) fully
tightened
Body loose Deck-mounted bath filler tap:
Is the locknut(13) underneath fully tightened
Deck-mounted bath shower mixer tap:
Is the locknut(15) underneath fully tightened

Maintenance
Replacement of Headwork
A B
Replacement of Aerator
Cleaning
To maintain the surface of your product, wipe with a clean damp cloth and wipe dry, do
not use any abrasive cleaning agents or materials. If any harsh chemicals come into
contact with the surface of the product, rinse and wipe clean immediately.