Birlea corona User manual

Vendor: S000238
Page 1 of 9
ASSEMBLY INSTRUCTIONS
CORONA 3 DRAWER BEDSIDE CHEST
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR USING YOUR CORONA 3
DRAWER BEDSIDE CHEST.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ASSEMBLY INSTRUCTIONS:
Please check contents and read instructions carefully before commencing assembly.
To avoid damages assemble the item on a soft, clean surface.
Assemble in the room of use.
HEALTH & SAFETY:
DO NOT use this item if any parts are missing, damaged or worn.
DO NOT use this item unless all fi ings are secured.
Always use on a level, even surface.
It is recommended that two people handle and assemble the item.
Keep small parts out of the reach of children.
CARE & MAINTENANCE:
This product is manufactured in pine which is a wood with natural characteristics including knots, grains,
clusters or indentations.
On unpacking the item you may notice an odour due to the production process, however, this will disappear
after a period of time.
DO NOT place the item ne t to a radiator or direct sunlight as this item is susceptible to temperature
change. It is recommended to maintain an even room temperature with no sudden fluctuations.
For general cleaning use a duster or damp cloth (almost dry) not wet – do not use soap and water,
detergents, aerosol sprays or any polish as the use of these materials would invalidate any claims.
You may wish to re-treat the surface to maintain the original finish. This can be done using block wa (un-
perfumed). Please follow the manufacturer’s instructions carefully.
DO NOT place the item onto wet or damp flooring as staining may occur to the floor.
Periodically check all screws & fi ings to ensure they are secure.
DO NOT push the item as this will damage the base.
Keep any sharp objects away from the item.
www.birlea.com

Vendor: S000238
Page 2 of 9
Parts List Har ware List
Part Description Qty Part Description Qty
1
Top Panel
1
A Wooden Dowel 26
2
Right Panel
1
B 14 mm Screw 2
3
Left Panel
1
C 30 mm Screw 30
4
Rear Base Plinth
1
D 35 mm Screw 34
5
Back Panel
1
E 19 mm Bolt 3
6
Front
Plinth
1
F
Handle
3
7
Side Plinth
2
G
Stud
4
8
Right Front Frame
1
H Tack
18
9
Lef
t Front Frame
1
** You will nee a small mallet an a screw river.
10
Top Front Frame
3
11
Bottom Front Frame
1
12
Drawer Front
3
13
Drawer Side
6
14
Drawer Back
3
15
Drawer Base
3
16
Drawer Runner
6
17
Cleat
4

Vendor: S000238
Page 3 of 9
Step 1: Attach the right front frame (8) to the right panel (2) using the cleats (17) and hardware part D with a
screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000238
Page 4 of 9
Step 2: Attach the left front frame (9) to the left panel (3) using the cleats (17) and hardware part D with a
screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Step 3: Insert hardware part A using a small mallet (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000238
Page 5 of 9
Step 4: Insert the top front frames (10) and bottom front frame (11) to the left panel (3). Attach the rear
base plinth (4) using hardware part D and a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Step 5: Attach the right panel (2) using hardware part D and a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000238
Page 6 of 9
Step 6: Attach the top panel (1) using hardware part D, then secure the bottom front frame (11) using
hardware part B. You will need to use a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Step 7: Attach the drawer runners (16) using hardware part D and a screwdriver (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000238
Page 7 of 9
Step 8: Attach the side plinths (7) and the front plinth (6) using hardware part C and a screwdriver (not
provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Step 9: Insert hardware part G with a small mallet (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000238
Page 8 of 9
Step 10: Attach the back panel (5) using hardware part H and a small mallet (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Step 11: Assemble the drawer components using hardware parts C, E and F with a screwdriver (not
provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.

Vendor: S000238
Page 9 of 9
Step 12: Insert the assembled drawers and secure using hardware part A and a small mallet (not provided).
DO NOT use any power tools as this may amage the frame an will invali ate any claim.
Additional Information:
• For complete product information, images and dimension diagrams please visit the website
www.birlea.com
• If you have any issues with your item please contact the retailer directly you purchased it from who
will be able to resolve any issues with Birlea.
• Why don’t you send us photos of your assembled furniture to [email protected] to be shared in our
#birleahome feature on Instagram.