Birlea S000238 User manual

Code: S000238
ASSEMBLY INSTRUCTIONS
4'6 CORONA LOW END BED
f
You
Tube
!
Assembly Instructions
- Please check contents and read instructions carefully before commencing assembly.
- To avoid damage assemble product on a soft, clean surface.
- The only tools required are a small mallet and screwdriver.
- Do not use power tools as this might damage the product and make it unsafe. This will also invalidate any claim.
- Assemble the product in accordance with instructions defined.
- It is recommended that two people handle and assemble product.
- This product is manufactured in pine which is a wood with natural characteristics including knots, grain and clusters or indentations.
- On unpacking the furniture you may notice an odour due to the production process. However, this will disappear after a period of time.
- For care and maintenance please refer to the attached details.
Care & Maintenance
- To enjoy your new furniture for many years please follow our recommendations below.
- Do not place product next to a radiator or direct sunlight. This product is manufactured in pine but is susceptible to temperature
change. It is recommended that an even room temperature be maintained with no sudden temperature fluctuation.
- Do not place hot or cold items directly onto the surface. Always use a placemat or marking will occur.
- For general cleaning use a duster or damp cloth (almost dry) not wet
- Do not use soap and water, detergents, aerosol sprays or any polish. The use of the materials above would invalidate any claim.
- You might wish to re-treat the surface from time to time to maintain the original finish.
This can be done by using block wax (unperfumed). Please follow the manufacturer's instructions carefully.
- Carry out regular inspection to ensure fittings are secure. Please be careful not to over tighten fittings.
- Do not place furniture on wet or damp floor as staining may occur to your floor.
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO
ASSEMBLE OR USE YOUR 4'6 CORONA LOW END BED.
4 m
4m
1170mm
1484mm
2060mm
630mm

PARTS LIST
Part Item Qty
HARDWARE LIST
Part Item Qty
1
1
1
1
1
1
26
2
2
1
1
2
3
4
5
6
7
8
9
10
1
30mm dowel
16mm Screw
35mm Screw
32mm Bolt
Nut
50mm Bolt
130mm Bolt
Half moon nut
Metal bracket
Round metal stud
Code: S000238
A
D
G
K
B
E
H
L
C
F
J
8
4
2
52
8
2
2
10
8
8
2
7
8
9
10
1
3
4
11
7
9
Headboard panel
Footboard panel
Left headboard post
Support leg
Left footboard post
Right headboard post
Right footboard post
Slat pack
Side rail
Centre rail
Headboard rail
N
P
M1
2
4
40mm dowel
130mm Bolt
Allen key
Spacer
2
6
5

Code: S000238
STEP 1
Attach the support legs to the centre rail using hardware part and the Allen key as provided.
Insert the 40mm wooden dowels to the side rails using a small mallet (not provided)
DO NOT use any power tools as this may damage the item and will invalidate any claims.
2x 9
10
8
8
STEP 2
Insert the 30mm wooden dowels to the headboard panel , footboard panel and headboard rail
using a small mallet (not provided).
1
11
108
9
G
G
M
B
B
A
A
A
A
A
A
1 2 11
2

Code: S000238
STEP 3
Attach the left headboard post and right headboard post to the headboard panel and
headboard rail using hardware part and the Allen key provided.
DO NOT use any power tools as this may damage the item and will invalidate any claims.
1
3
4
11
4
3
65
M
H
H
H
H
H
H
H
M
H
STEP 4
Attach the left footboard post and right footboard post to the footboard panel using hardware
part and the Allen key as provided.
DO NOT use any power tools as this may damage the item and will invalidate any claims.
341
11 H
H
6 5 2
H
H
2
6
5

Code: S000238
STEP 5
Fix the metal brackets to the headboard rail and footboard panel using hardware
part and a screwdriver (not provided).
DO NOT use any power tools as this may damage the item and will invalidate any claims.
9
10
1
9
1
9
10
STEP 6
Attach the side rails to the headboard posts using hardware parts and with the Allen key as provided.
Then fix the centre rail to the metal bracket using hardware parts and .
DO NOT use any power tools as this may damage the item and will invalidate any claims.
L
L
L
C
M
J
E
F
K
11 2
L
11
9JK
10 E F
2

Code: S000238
STEP 7
Attach the footboard posts to the side rails using hardware parts and with the Allen key as provided.
Then fix the centre rail to the metal bracket using hardware parts and .
DO NOT use any power tools as this may damage the item and will invalidate any claims.
STEP 8
Fix the slats to the side rails and centre rail using hardware parts and with a screwdriver
(not provided).
Make sure to start from the ends of the bed frame and work towards the middle of the bed.
DO NOT use any power tools as this may damage the item and will invalidate any claims.
10
9
10
9
7
77
7
b:
7
7
a:
7
7
M
J
K
E
F
N
D
N
D
9JK
10 E F
79 10 DN
2
92

Code: S000238
STEP 9
Insert the metal studs to the bed posts at the dimensions as shown in the diagram using a
small mallet (not provided).
DO NOT use any power tools as this may damage the item and will invalidate any claims.
160mm
50mm
40mm
40mm
P P
P
P