Bissell Lift-Off 66E1 SERIES User manual

BISSELL is happy to be of service.
Contact us directly at 1-800-237-7691 or
visit the website for helpful instructions at
www.bissell.com
Quick Start
Guide
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE
PLEASE KEEP FOR FUTURE REFERENCE
BISSELL Homecare, Inc.
P.O. Box 1888
Grand Rapids, MI 49501
Part #120-4562
© 2012 BISSELL Homecare, Inc.
For additional tips and troubleshooting
Please refer to User's Guide
Visit: www.bissell.com
a. d.
e.
b. c.
TOOLS NEEDED: Standard #2 X 4 inch Phillips head screw driver
Color and tools may vary depending on the model you purchased
Package contents:
66E1, 80X9,
30K7, 24A4 SERIES
a. Upper Handle
b. Portable Spot Cleaner/Base
c. 4 Screws – taped to handle
d. Tool Attachment(s)
(varies by model)
e. BISSELL 2X Formula
(varies by model)
Carpet cleaning (portable mode)
1. Step on the portable spot cleaning pedal and lift up to release
the portable spot cleaner
2. Fill the tank following instruction #1 under Carpet Cleaning (Upright Mode)
3. Release ex hose by turning the hose secure latch
4. Plug power cord into proper outlet and press the power button
5. Cleaning
a. Clean by pressing the trigger on the ex hose to spray solution
onto the area to be cleaned
b. Slowly scrub the tool back and forth over the soiled surface
c. Tilt the tool forward to suction liquid
6. Empty dirty tank when it reaches the “FULL” line following instruction
#3 under Carpet Cleaning (Upright Mode)
7. When cleaning is complete, replace unit on base of machine
a. Align the product as image 7a shows and rmly push down
the portable spot cleaner until it is secured on both sides
b. Check gray latches on both sides to conrm it is secured.
NOTE: Portable spot cleaner must be fully secure to operate
in upright mode
1. 3.
WARNING:
Refer to the enclosed user guide for
complete instructions and important
safety notices.
7a.
CORD
SIDE HOSE
SIDE
7b.

1. Slide upper handle onto body of machine
2. Locate the screws (taped to handle) and
the 4 screw holes marked by arrows
NOTE: 2 screw holes are located
under the support handle
3.
Firmly holding the upper handle in place,
screw 2 screws into the marked holes at
an upward angle above the support handle
4. Screw the remaining 2 screws at an
upward angle into the marked outmost
holes under the support handle.
5. Wrap power cord around cord wrap
(located on the side of the portable spot cleaner)
6. Attach tough stain tool to end of hose
(extra tool storage located on back)
7. Wrap ex hose and secure with hose latch
(located on opposite side of cord wrap)
1. Move furniture to another area if cleaning
an entire room
2. Vacuum area with a dry vacuum cleaner
3. PreTreat spots & stains and heavy trafc areas (optional—see User’s Guide)
2. Cleaning
a. Plug the power cord into a proper outlet and press the power button
b. Check to verify that the heat indicator light is illuminated.
If heat indicator light does not illuminate, release
the pod and re-secure by pushing rmly until both
sides snap into place.
NOTE: Allow 1 minute for hot water heater to warm-up
c. While pressing the trigger, make one slow forward wet pass and
another one back
d. Release the trigger and make another slow forward and backward
pass over the same area. Repeated passes will help remove moisture.
e. Continue passes until the cleaning area is complete
3. Empty dirty tank when it reaches the “FULL” line
a. Press the power button to turn off the machine
b. Remove dirty tank
c. Unlock the tank lid by rotating the handle over the back of the tank
d. Remove lid to pour out dirty water and rinse
e. Replace top of tank and rotate the handle forward to lock in place
f. Before replacing tank on machine wipe debris from red lter
4. Rell as needed following step #1 under Carpet Cleaning (Upright Mode)
to continue cleaning
1. Fill the formula & water tank
a. Remove the formula tank from the base of the machine (located on
back of portable spot cleaner)
b. Unscrew the black cap and remove insert
c. Fill tank with hot tap water to the WATER ll line and add two ounces
of BISSELL 2X formula
d. Replace the insert and tighten black cap
e. Replace formula tank on machine
1a.
3d.
3b.
1b.
3e.
1e.
3c.
3f.
For complete user's guide, visit www.bissell.com
Assembly Carpet cleaning (upright mode)
Before carpet cleaning
Carpet cleaning (upright mode)
6.
7.
1.
3.
2.
4.
WARNING:
Unit will not function correctly if
pod is not secured on both sides.