Bittel UNOVoice 67 Series User manual

UNOVoice (67 Series) Analogue Telephone User Manual
Version 1.0.1

© Bittel Electronics (EU) Limited, 50 Broadway, London SW1H 0RG United Kingdom. Page 2
Thank you for purchasing the Bittel UNO
Bittel’s UNO series telephones are specially designed to meet the exacting needs of the modern hotel guest
room. We have combined first class materials, proven technology and leading-edge design to bring you the
award-winning UNO range of guest room telephones.
UNO Voice –Main Features
Bittel’s UNO series telephones are specially designed to meet the exacting needs of the
modern hotel guest room. We have combined first class materials, proven technology and
leading-edge design to bring you the award-winning UNO range of guest room telephones.
Key features as below:
Up to 10 Guest Service Keys / “speed-dial”permanent memory keys
Guest Service keys may be programmed manually or using our patented hand-held
cloning device
Large-area interchangeable faceplate for displaying hotel branding and dialing
instructions
Message waiting light indicator and message retrieval button compatible with all
mainstream PBX
Hearing aid compatible (HAC) handset
Speaker and handset volume are both adjustable to three levels
Ringer volume may be adjusted to a high or low setting according to a guest’s ease of
hearing
Default 600ms hook-switch flash time, manually adjustable
Auto-connect: If the handset is accidentally left off-hook or unsecured, the phone will
detect this and ring for inbound calls as normal
Privacy Redial: For the guest’s privacy the last number dialled will automatically leave
the phone’s memory after 5 minutes.
Hold key for placing a call in waiting mode
Half-duplex Speakerphone for on-hook use of the phone (TSD models only)
Line 1 and Line 2 automatic selection and Conference calling function (Two-line
phones only)
Data port –RJ11 pass through for dial-up internet or facsimile use

© Bittel Electronics (EU) Limited, 50 Broadway, London SW1H 0RG United Kingdom. Page 3
INSTALLATION
1. Assembly of phone base, facia component and faceplate
The base section of the UNO attaches to the rear of the main phone facia as follows:
Once located, slide the base into the fixing points as shown below:
Once secured correctly as shown, use the supplied screws to secure the two
components together.

© Bittel Electronics (EU) Limited, 50 Broadway, London SW1H 0RG United Kingdom. Page 4
Screw
Paper
Holder
Port for holder
Location of the screws (may vary by product):
Installation of Faceplate:

© Bittel Electronics (EU) Limited, 50 Broadway, London SW1H 0RG United Kingdom. Page 5
LINE 2
VOL +VOL -CONF
REDIAL
FLASH
MUTE
SPKR
LINE 1
HOLD
7
6543
2
1
TIME SET
VOLUMETUNING
8
9
16 15
17
14 13
10 11
12
2. Handset Cord
Connect the handset cord to the jack in the handset and then insert the other end into
the hack on the under-side rear of the main phone facia unit (accessible underneath the
phone). Both jacks are labelled “2” and “12” in the diagram below.
Then secure the cable in place along the provided cable run to ensure the unit sits flush
on the table top.
3. Telephone LineCord
Insert the one end of the straight line cord into the jack labelled “TO TEL” (labelled no.14
in diagram below), and then insert the other end of the line cord into a telephone wall
jack / socket.

© Bittel Electronics (EU) Limited, 50 Broadway, London SW1H 0RG United Kingdom. Page 6
HOW TO USE THE TELEPHONE
1. Adjust the call volume
During the call, press the VOL+/- key to adjust the volume level of either the handset or
speaker-phone.
Handset volume will reset to the lower level and the speaker-phone will store the current
level once the call is terminated.
2. How to switch from Handset to speaker-phone
a) From handset to speaker
Just press SPKR key and replace the handset in the cradle
b) From speaker to handset
Just lift handset
3. Receiving new call
a) When the phone rings, just lift up the handset to answer the call, or press SPKR for
hands-free
b) For two line call mode, when line-1 has a call and another call comes in on line-2, just
press corresponding LINE key to answer the new call and the other call will hang up
automatically. Should you wish to keep the current call, press the HOLD key to place the
current call on hold and then switch to the respective line using the LINE keys.
3. Three way conference
In order to establish a conference call (2-line phones only), press the HOLD key to hold the
current call, then dial out and establish a call on the second line (line-2). Once both calls are
established, press the CONF key to enter into the three-way conference mode. Replace the
handset in the cradle to finish the conference call.
Should you wish to speak with only one party during the conference call, press the
accordance relevant LINE key to relieve the conference mode and talk with one caller.
Alternatively press the HOLD key to hold the two lines and then press the desired line key to
talk with the selected line, then press CONF key to resume the conference mode.

© Bittel Electronics (EU) Limited, 50 Broadway, London SW1H 0RG United Kingdom. Page 7
4. To redial the last number dialled
Press the REDIAL key to dial the last number dialled. Please remember that after five
minutes the number will disappear automatically to ensure the guest’s calling history
remains private.
5. Using the hold key
In off-hook mode, press the HOLD key (the corresponding LED indicator light will illuminate)
and replace the handset. The current line is now in hold mode. Lift up the handset again
and the call comes out of hold mode, and the two-way conversation is available again.
If a second telephone (in parallel) answers the call, the original phone will detect the current
status and release the hold mode and restore the on-hook status.
6. Mute
During the call, press the MUTE key once to stop voice transmission from the user handset or
speaker to the caller (the corresponding LED indicator light will illuminate). To restore two-
way communication press the MUTE key again to relieve the mute mode.
7. Adjust ring volume
With the ringer volume control located on the reverse of the telephone, select the
appropriate Hi or Low ringer volume setting.
8. Auto-Connect
If the handset is not replaced securely on the cradle after the phone call, this function will
restore the phone’s on-hook status automatically after getting a busy signal within a defined
period of time.
9. Using one touch memory keys (Guest Service Keys)
Lift up the handset or press SPKR, then press the required Guest Service Key (memory key)
to dial the required function or department.
How to store the memory number:

© Bittel Electronics (EU) Limited, 50 Broadway, London SW1H 0RG United Kingdom. Page 8
In on-hook mode, press HOLD key, then the desired number, then the HOLD key, then the
MEMORY key.
12. MWL
To retrieve a message, lift the handset or press SPKR and then press the message key.
Alternatively, with the phone on-hook, press the message key. Press the message key again
and it will restore its on-hook status.
How to store the message number:
In on-hook mode, press HOLD key + desired number +HOLD +MWL key
13. Automatic Programming of Guest Service / Memory Keys
For these instructions please refer to the user manual of the Bittel Handheld cloner and R.P
master cloner.
MAINTENANCE AND TROUBLESHOOTING
1. No dialing tone of handset
Check the telephone network
Check the connection of handset cord and straight line cord
2. No ringing or no continually ring
Check the telephone line
Check the quantity of parallel phone set
3. Noise during talk
Check the telephone line
Check the handset cord
FCC APPROVAL
Complies with Part 68 of the FCC rules. On the bottom of this telephone is a label that
contains, among other information, the FCC registration number and the ringer equivalence
number (REN) for this telephone. If requested, you must provide this information to the
Telephone Company.

© Bittel Electronics (EU) Limited, 50 Broadway, London SW1H 0RG United Kingdom. Page 9
CE APPROVAL
Complies with CE approval.
JACKS
Uses RJ11C USOC standard modular jacks.
WARRANTY
This product is warranted for a period of 5 years from the date of purchase against faulty
materials or workmanship. If during this period a defect arises, we may repair or replace the
product, at Bittel’s discretion, provided that:
1) The product has not been used for any purpose other than normal use,
2) Unauthorized product repair or modifications have not been attempted.
3) The product has never been used in a harsh or corrosive environment.
4) No damage in transit
THIS LIMITED WARRANTY GIVES THE BUYER SPECIFIC LEGAL RIGHTS. THE BUYER MAY ALSO
HAVE OTHER RIGHTS WHICH VARYFROM JURISDICTION TO JURISDICTION.
This warranty is only valid for merchandise purchased directly from Bittel or authorised
dealers or distributors of Bittel Electronics.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CONTACTING BITTEL
Address: Bittel Electronics (EU) Limited, 50 Broadway, London SW1H 0RG. United
Kingdom
Tel: [phone]
Fax: [phone]
Email: suppo[email protected]m