Black Horse Off Road 17TS27MA User manual

BLACK MODULAR GRILLE GUARD FOR TOYOTA SEQUOIA 01-07/ TUNDRA 00-06
Page 1 of 4
INSTALLATION INSTRUCTIONS
BLACK MODULAR GRILLE GUARD FOR TOYOTA SEQUOIA 01-07/
TUNDRA 00-06
PART # 17TS27MA

BLACK MODULAR GRILLE GUARD FOR TOYOTA SEQUOIA 01-07/ TUNDRA 00-06
Page 2 of 4
READ THE INSTRUCTIONS COMPLETELY BEFORE YOU BEGIN THE INSTALLATION. NOTE: PICTURES
ARE FOR REFERENCE ONLY, ACTUAL PART MAY BU DIFFERENT. INSTALLATION IS THE SAME.
YOU MAY NEED TO PERIODICALLY TO RE-TIGHTEN ALLHARDWARE，SUCH AS ONE MONTH OR TWO
MONTT.
NO.
QTY
PICTUER
NO.
QTY
PICTUER
○
1E1
GRILL GUARD
A○ 2E2
Left & Right Brush Guard
A○ 3E2
Frame Mounting Bracket
A○ 4E2
Top Bracket
A○ 5E6
Hex Nut M12_35
A○ 6E12
Flat Washer D12
A○ 7E6
Spring Washer D12
A○ 8E6
Hex Nut M12
A○ 9E6
Hex Bolt M8_25
A○ 10E12
Flat Washer D8
A○ 11E6
Spring Washer D8
A○ 12E6
Type 1 non-metallic insert
Hexagon lock nut M8
A○ 13E6
Hex Bolt M6_25
A○ 14E6
Flat Washer D6
Parts list
Before Installation

BLACK MODULAR GRILLE GUARD FOR TOYOTA SEQUOIA 01-07/ TUNDRA 00-06
Page 3 of 4
A○ 15E6
Type 1 non-metallic insert
Hexagon lock nut M6
A○ 16E1
Allen Wrench S=5
A○ 17E1
Allen Wrench S=4
INSTALLING PICTURE
Installation Steps
Mount frame brackets to the hooks bolts
Top bracket with black epoxy
9、10、11、12
5
、
6
、
7
、
8
13
、
14
、
15
Attach to existing holes on vehicle
1
2
3
4

BLACK MODULAR GRILLE GUARD FOR TOYOTA SEQUOIA 01-07/ TUNDRA 00-06
Page 4 of 4
INSTALLING THE FRAME BRACKETS
1) REMOVE FACTORY TOW HOOKS (BUT DO NOT DISCARD THE FACTORY BOLTS) THE BOLT PATTERN
ON THE FAAME MOUNTING BRACKETS WILL BE POSITIONED IN MANNER SHOWN IN ILLUSTRATION
(PASSENGER SHOWN) ATTACH FRAME BRACKETS USING THE FACTORY BOLTS.
INSTALLING THE FRONT BAR
2) LINE UP THE THREE HOLES ON THE LOWER PORTON OF FRONT BAR WITH THE THREE HOLES ON THE
FRAME BRACKETS(OUTER EDGE)USING THE M12х30 HEX BOLT ,M12 HEX NUT AND 12mm FLAT WASHERS
TO FASHEN THE FRONT BAR TO THE FRAME BRACKETS.
3) REMOVE THE REVETS LOCATED UNDERNEATH THE VEHICLE IN ORDER TO INSTALL THE L-SUPPORT
BRACKETS,ATTACH L-SUPPORT BRACKETS USING THE M6X25 SCREWS,M6 HEX NYLOK NUTS ,6mm FLAT
WASHER AND M12х30 HEX BOLTS, 12mm FLAT WASHERSAND M12 HEX NUT.
4) ONCE THE FRONT BAR IS ATTACHING TO ALL MOUNTING BRACKETS ALIGN THE LEFT AND RIGTH
SIDE OF THE FRONT BAR TO THE BUMPERAND TIGHTEN ALLFASTENERS.
Any damages and losses caused by improper installation and application, goes beyond our
quality warranty.
NOTE