Black Horse Off Road EX-K376 User manual

EXCEED RUNNING BOARD FOR 2020 KIA TELLURIDE
Page 1 of 5 4/23/20 (AL)
INSTALLATION INSTRUCTIONS
PREMIUM RUNNING BOARD
FOR 2020 KIA TELLURIDE
PART # EX-K376

EXCEED RUNNING BOARD FOR 2020 KIA TELLURIDE
Page 2 of 5 4/23/20 (AL)
PARTS LIST:
1
Driver/Left Running Board
8
10mm Plastic Retainers
1
Passenger/Left Running Board
8
10mm x 30mm OD x 2.5mm Flat Washers
1
Driver/Left Front Mounting Bracket
8
10mm Nylon Lock Nuts
1
Passenger/Right Front Mounting Bracket
2
8-1.25mm x 25mm Hex Bolts
1
Driver/Left Front Support Bracket
4
8mm x 24mm OD x 2mm Flat Washers
1
Passenger/Right Front Support Bracket
2
8mm Lock Washers
1
Driver/Left Center Mounting Bracket
2
8-1.25mm Hex Nuts
1
Passenger/Right Center Mounting Bracket
12
6-1.0mm x 20mm T-Bolts
1
Driver/Left Rear Mounting Bracket
16
6mm x 18 OD x 1.6mm Flat Washers
1
Passenger/Right Rear Mounting Bracket
16
6mm Lock Washers
8
10-1.5mm x 40mm Bolt Plates
16
6mm Hex Nuts
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. CUTTING IS REQUIRED TO INSTALL.
2. Remove the cover panels on the bottom of the vehicle.
3. Locate the Driver/Left mounting location and remove the factory round rubber plug in the bottom of the
outer rocker panel, (Figure 1).
4. Select (1) 10mm Bolt Plate. Insert the Bolt Plate into the hole. Thread (1) 10mm Plastic Retainer to the
Bolt Plate to hold it in place, (Figure 2).
5. Select the Driver/Left Front Mounting Bracket. Attach the Mounting Bracket to the Bolt Plate with (1)
10mm Flat Washer and (1) 10mm Nylon Lock Nut, (Figure 2). Attach the Bracket to the stud with (1)
6mm Flat Washer, (1) 6mm Lock Washer and (1) 6mm Hex Nut. Do not tighten hardware.
6. Locate the inner hole behind the Driver/Left Front Mounting Bracket. Repeat Step 4 to insert (1) 10mm
Bolt Plate, (Figure 4).
7. Select the Driver/Left Support Bracket. Attach the Support Bracket to the Bolt Plate in the inner hole
with (1) 10mm Flat Washer and (1) 10mm Nylon Lock Nut, (Figure 5). Attach the Support Bracket to
the Mounting Bracket with (1) 8mm Hex Bolt, (2) 8mm Flat Washers, (1) 8mm Lock Washer and (1)
8mm Hex Nut, (Figures 6 & 7). Do not tighten hardware.
8. Move to the center mounting location. Repeat Steps 4 & 5 to attach the Driver/Left Center Mounting
Bracket to the center mounting location, (Figures 8 & 9). Do not tighten hardware.
Driver/Left
Rear Bracket
Driver/Left
Running Board
Front
Passenger/Right
Rear Bracket
Passenger/Right
Front Bracket
Passenger/Right
Center Bracket
Driver/Left
Center Bracket
Driver/Left
Front Bracket
Passenger/Right
Support Bracket
Driver/Left
Support Bracket

EXCEED RUNNING BOARD FOR 2020 KIA TELLURIDE
Page 3 of 5 4/23/20 (AL)
9. Move to the rear mounting location. Repeat Steps 4 & 5 to attach the Driver/Left Rear Mounting
Bracket, (Figures 10—12). Do not tighten hardware.
10. Select the Driver/Left side factory plastic covers. Hold up each cover to the mounting locations. Mark
and cut each plastic cover along the marks to allow Brackets clearance. IMPORTANT: The covers
must be cut for bracket clearance.
11. Select and carefully unwrap the Driver/Left Running Board. Insert (6) 6mm T-Bolts in to the channels on
the bottom of the Running Board, (Figure 13). Attach the Running Board to the mounting brackets with
(6) 6mm Flat Washers, (6) 6mm Lock Washers and (6) 6mm Hex Nuts, (Figure 14).
12. Level and adjust the Running Board and tighten all hardware.
13. Reattach the plastic covers.
14. Repeat Steps 2—13 for the Passenger/Right Running Board installation.
15. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the
finish. Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be used also to
clean the Running Board. Driver/Left Side Installation Pictured
(Fig 3) Attach the Driver/Left Front
Mounting Bracket to the Bolt Plate
10mm Bolt Plate
10mm Plastic Retainer
10mm Flat Washer
10mm Nylon Lock Nut
Insert the factory
stud into slot, use:
6mm Flat Washer
6mm Lock Washer
6mm Hex Nut
(Fig 2) Insert (1) 10mm Bolt Plate into the
hole. Thread (1) 10mm Plastic Retainer
onto the Bolt Plate to hold it in place
(Fig 1) Driver/Left front outer mounting location
Front
Front
Front

EXCEED RUNNING BOARD FOR 2020 KIA TELLURIDE
Page 4 of 5 4/23/20 (AL)
Driver/Left Side Installation Pictured
(Fig 5) Attach the Driver/Left Front
Support Bracket to the Bolt Plate
(Fig 7) Driver/Left Brackets attached
to the front mounting locations
(Fig 4) Insert (1) 10mm Bolt Plate into the
inner hole. Thread (1) 10mm Plastic Retainer
onto the Bolt Plate to hold it in place
Front
10mm Bolt Plate
10mm Plastic Retainer
10mm Flat Washer
10mm Nylon Lock Nut
Front
Front
(Fig 6) Attach the Support Bracket
to the Mounting Bracket
Front
8mm Hex Bolt
(2) 8mm Flat Washers
8mm Lock Washer
8mm Hex Nut

EXCEED RUNNING BOARD FOR 2020 KIA TELLURIDE
Page 5 of 5 4/23/20 (AL)
Driver/Left Side Installation Pictured
(Fig 9) Attach the Driver/Left Center Mounting
Bracket to the center mounting location
(Fig 10) Insert (1) 10mm Bolt Plate into the
rear hole. Thread (1) 10mm Plastic Retainer
onto the Bolt Plate to hold it in place
Front
Rear
(Fig 8) Insert (1) 10mm Bolt Plate into the
center hole. Thread (1) 10mm Plastic
Retainer onto the Bolt Plate to hold it in place
10mm Bolt Plate
10mm Plastic Retainer
10mm Flat Washer
10mm Nylon Lock Nut
Front
Insert the factory
stud into slot, use:
6mm Flat Washer
6mm Lock Washer
6mm Hex Nut

EXCEED RUNNING BOARD FOR 2020 KIA TELLURIDE
Page 6 of 5 4/23/20 (AL)
Driver/left Side Installation Pictured
(Fig 12) Driver/Left Rear Mounting Bracket
attached to the rear mounting location
(Fig 11) Attach the Driver/Left Rear
Mounting Bracket to the Bolt Plate
Rear
Rear
Front
(Fig 13) Insert (2) T-Bolts into the channels
on the bottom of the Running Board
(2) 6mm T-Bolts
(Fig 14) Attach the Driver/Left Running
Board to the Mounting Brackets
(2) 6mm Flat Washers
(2) 6mm Lock Washers
(2) 6mm Hex Nuts
10mm Bolt Plate
10mm Plastic Retainer
10mm Flat Washer
10mm Nylon Lock Nut