BluDot Keeps Quick start guide

Keeps Table Collection
DESIGNED IN 2019
ASSEMBLY NOTES | REV 01
@BLUDOT
We design all our pieces in our Minneapolis studio. Follow
along on Instagram for some sneak peeks into the process.
NEED A HAND?
Contact us at [email protected] or
844.425.8368 for assistance.

2 | 844.425.8368 KEEPS TABLE COLLECTION
Support Rail
3 | 2*QTY
Metal Bracket
4QTY
Pt. 1057
12QTY
Pt. 1104
9 | 6*QTY
Pt. 5018
6 | 4*QTY
Pt. 5014
QTY 12 | 8*
Leg Frame
2QTY
Top Panel
1QTY
Pt. 5019
6 | 4*QTY
Pt. 9016
1QTY
Pt. 9023
QTY 1
Pt. 3002
21 | 18*QTY
Hardware and part quantities listed for 100” table. The 76” Table ships with quantities called out with an *
Parts & Hardware

[e-mail] |3ASSEMBLY NOTES
PT. 1104 x 9 | 6* PT. 3002 x 9 | 6* PT. 9016 x 1
Hardware and part quantities listed for 100” table. The 76” Table ships with quantities called out with an *
Step 01
ATTACHING SUPPORT RAILS.
Place the top panel face down on a
soft surface. Align x2 support rails
with threaded inserts on the top panel.
Partially tighten Pt. 1104.

4 | 844.425.8368 KEEPS TABLE COLLECTION
PT. 5019 x 6 | 4*
Hardware and part quantities listed for 100” table. The 76” Table ships with quantities called out with an *
Step 02
PREPARING THE SUPPORT RAILS.
Align the arrow on Pt. 5019 parallel to the top
panel and facing towards the outer edge of the
support rail. Press Pt. 5019 into the pre-drilled
holes on the support rails.

[e-mail] |5ASSEMBLY NOTES
PT. 5014 x 12 | 8* PT. 5018 x 6 | 4* PT. 9016 x 1
Hardware and part quantities listed for 100” table. The 76” Table ships with quantities called out with an *
NOTE:Confirm hole
alignment for the support
rail. If holes don’t align,
install the leg frame on the
other side of the table.
Step 03
ATTACHING THE LEG FRAMES.
Place the leg frames on a soft surface. Using a
screwdriver install Pt. 5018 as shown. Install
Pt. 5014 and align the pre-drilled holes on the
leg frames with Pt. 5014.

6 | 844.425.8368 KEEPS TABLE COLLECTION
PT. 9023 x 1
Slide Frame
Slide Frame
Step 04
SECURING THE LEG FRAMES.
Using Pt. 9023 turn the hardware clockwise
until secured. After securing the leg frames,
center the base assembly on the top panel by
sliding as shown.

[e-mail] |7ASSEMBLY NOTES
PT. 1057 x 12 PT. 3002 x 12 PT. 9016 x 1
Step 05
INSTALLING THE METAL BRACKETS.
Begin installing the metal brackets to the leg
frames as shown. Complete installation by
securing the metal brackets to the top panel.

BLU DOT DESIGN & MANUFACTURING, INC. DESIGNED IN MINNEAPOLIS, MN
PT. 9023 x 1
Additional Information
CLEAN
Clean with a slightly damp, soft cloth. To remove dirt
and fingerprints, use a quality cleaner formulated for
wood furniture. Wipe completely dry with a soft cloth
in the direction of the wood grain.
Step 06
FINISH TIGHTENING THE SUPPORT RAILS.
Finish tightening Pt. 1104 before first use.
Store Pt. 9016 and Pt. 9023 in the provided
storage cradle. Periodically use the provided
hardware to tighen connections.