BluDot Modu-licious #4 Quick start guide

Modu-licious #4
DESIGNED IN 1999
ASSEMBLY NOTES | REV 01
NEED A HAND?
Contact us at [email protected] or
844.425.8368 for assistance.
YOU WANT CHOICES, WE GOT CHOICES.
Drawers and doors are your canvas with the award-winning
Modu-licious series.

1 | 8 4 4 . 4 2 5 . 8 3 6 8 MODU-LICIOUS #4
Pt. 5001
24QTY
Pt. 1023
16QTY
Pt. 4005
QTY
Pt. 8018
4QTY4
Pt. 5005
24QTY
Pt. 5002
24QTY
Pt. 1218
QTY
Pt. 1217
2QTY2
Pt. 8046 Pt. 8042
2 1QTY QTY
8042
Anti-tip Strap
Parts & Hardware

[e-mail] | 2ASSEMBLY NOTES
Bottom Panel
1QTY
Top Panel
1QTY
Drawer
4QTY
Foot
2QTY
Drawer Slide
8QTY
Stretcher
1QTY
Center Panel
1QTY
Side Panel
2QTY
Back Panel
2QTY
Parts & Hardware

3 | 8 4 4 . 4 2 5 . 8 3 6 8 MODU-LICIOUS #4
354
1 2
How to use the cam lock system
Note direction of cam arrow. Turn cam clockwise 1/2 turn or until tight. Note direction of cam arrow.

[e-mail] | 4ASSEMBLY NOTES
PT. 5001 X 2 PT. 5002 X 2 PT. 4005 X 4
Step 01
ASSEMBLE BASE.
Using the stretcher and feet assemble the
base as shown. Refer to page 3 on how to use
the cam lock system.

5 | 8 4 4 . 4 2 5 . 8 3 6 8 MODU-LICIOUS #4
PT. 5001 X 4 PT. 5002 X 4
Bottom Panel
Step 02
ATTACH BOTTOM PANEL.
Attach the bottom panel to the base using
the provided hardware as shown. Refer to
page 3 on how to use th cam lock system.

[e-mail] | 6ASSEMBLY NOTES
PT. 1023 X 16
Right Side Panel
1023
5mm x 10.5mm
Hafele # 013.14.718
Philips Drive
Varianta Screw
1023
5mm x 10.5mm
Hafele # 013.14.718
Philips Drive
Varianta Screw
1023
5mm x 10.5mm
Hafele # 013.14.718
Philips Drive
Varianta Screw
1023
5mm x 10.5mm
Hafele # 013.14.718
Philips Drive
Varianta Screw
1023
5mm x 10.5mm
Hafele # 013.14.718
Philips Drive
Varianta Screw
1023
5mm x 10.5mm
Hafele # 013.14.718
Philips Drive
Varianta Screw
1023
5mm x 10.5mm
Hafele # 013.14.718
Philips Drive
Varianta Screw
1023
5mm x 10.5mm
Hafele # 013.14.718
Philips Drive
Varianta Screw
1023
5mm x 10.5mm
Hafele # 013.14.718
Philips Drive
Varianta Screw
Step 03
ATTACH DRAWER SLIDES.
Attach drawer slides to side panel as shown
using the provided hardware. Repeat for left
side panel.

7 | 8 4 4 . 4 2 5 . 8 3 6 8 MODU-LICIOUS #4
PT. 5001 X 6 PT. 5002 X 6 PT. 5005 X 8
Center Panel
Side Panel
Side Panel
Step 04
BEGIN ASSEMBLING CASE.
Attach side panels to center panel as shown
using the provided hardware. Refer to page 3
on how to use the cam lock system.

[e-mail] | 8ASSEMBLY NOTES
PT. 8018 X 4
Step 05
INSERT BACK PANELS.
Add rubber gromates to each panel
as shown. Insert panels into grooves
in case.

9 | 8 4 4 . 4 2 5 . 8 3 6 8 MODU-LICIOUS #4
PT. 5001 X 6 PT. 5002 X 6 PT. 5005 X 8
Top Panel
Step 06
FINSIH ASSEMBLING CASE.
Finish assembling the case by attaching the
top and bottom panels as shown using the
provided hardware. Refer to page 3 on how to
use the cam lock system.

[e-mail] | 10ASSEMBLY NOTES
Step 07
INSTALL DRAWERS.
To install the drawers extend drawer slides out
from case, align with drawer slides as shown,
and slide drawer in. Be sure to push until
drawer is completely closed and engaged.

11 | 8 4 4 . 4 2 5 . 8 3 6 8 MODU-LICIOUS #4
PT. 8046 X 1 PT. 1218 X 2
1” lower than
case top
Side Panel
Wall
Step 08
ATTACH ANTI-TIP BRACKET TO THE WALL.
Install anti-tip bracket to wall stud 1-inch
below case top panel height.

[e-mail] | 12ASSEMBLY NOTES
PT. 8046 X 1 PT. 1217 X 2
Top
Back
Panel
Step 09
INSTALL ANTI-TIP BRACKET TO CASE.
Bracket must be installed to top panel of case.
In order to prevent damage, it is recommended
that 3/32” pilot holes be drilled prior to
installation.

13 | 8 4 4 . 4 2 5 . 8 3 6 8 MODU-LICIOUS #4
PT. 8042 X 1
8042
Anti-tip Strap
Step 10
SECURE THE CASE.
Install and tighten the strap prior to using
the product.

[e-mail] | 14ASSEMBLY NOTES
Additional Information
TO REMOVE DRAWERS
Pull lever up on the right side and push down on the left side
of the drawer slide. With levers engaged pull drawer out.
TO ADJUST DRAWER FRONTS
Loosen the acorn nuts, adjust drawer
front, re-tighten acorn nuts.

BLU DOT DESIGN & MANUFACTURING, INC. DESIGNED IN MINNEAPOLIS, MN
Additional Information
CLEAN
Clean with a slightly damp, soft cloth. To remove dirt
and fingerprints, use a quality cleaner formulate for
wood furniture. Wipe completely dry with a soft cloth
in the direction of the wood grain.