Bobrick Classic Series Operating and maintenance manual

Installation Instructions
For Models:
Model Number / Description File Name
B-2112 Classic™ Series Surface-Mounted Soap Dispenser B-2112.pdf
1

INSTALLATION:
Lavatories: Locate dispenser so that spout will be
over the lavatory . Allow a minimum of 4'' (105mm)
clearance between top of dispenser and bottom of any shelf, cabinet, or other projection to provide
enough space to fill dispenser conveniently.
TO ATTACH WALL PLATE WITH SCREWS,
place screws in the three holes provided.
The surface on which unit is to be mounted determines type of screws required for best installation.
For plaster or dry wall on studs, provide concealed backing and secure dispenser wall plate with
mounting screws furnished by manufacturer.Backing must comply with local building codes.
For hollow tile partitions and other instances where applicable, use 1/8'' (3mm) round-head toggle
bolts.
For brick, concrete, or solid tile walls, use screws furnished with #8 (4mm) fiber plugs or provide
1/8'' (3mm) toggle bolts or expansion bolts.
INSTRUCTIONS FOR INSTALLATION AND MAINTENANCE
Bobrick Classic™ Series Models B-2111 and B-2112 Surface-Mounted Soap Dispensers
FIGURE 3FIGURE 2FIGURE 1
TO MOUNT DISPENSER:
1. Open filler-top by inserting BobKey (24-17) into slot of filler-top and then sliding latch to the left. Lift up filler-top.
2. Using screwdriver as shown (see Figure 1), loosen locking-screw (A).
3. Position dispenser so that edges of back plate (B) fit into grooves of wall plate and then press dispenser down into place (see Figure 2).
4. Tighten locking-screw against washer. Dispenser locks into place when point of locking-screw is lodged under lug (C) of wall plate (see
Figure 2).
CAUTION: Failure to tighten screw securely may cause dispenser to leak when filled above this point.
5. Close and lock filler-top by reversing operation in step 1 (see Figure 3).
MAINTENANCE:
1. To fill dispenser, open filler-top by inserting BobKey (24-17) into slot of filler-top and then sliding latch to the left.Lift up filler-top.Fill dispenser
with soap. Corrosion-resistant valve dispenses liquid soaps, lotions and detergents. Close filler-top and relock by inserting BobKey into filler-
top slot and sliding latch to the right.
2. Clean equipment operates better, lasts longer, and requires less maintenance.Wipe the unit daily, including the spout, using a damp cloth.
Never use abrasive cleaners .
3. Periodically clean the dispenser by pumping warm water mixed with soap from the dispenser through the vessel and valve to flush out
contaminants or dried soap residue.
Never use abrasive cleaners.
4. If the soap valve fails to operate satisfactorily, the problem may be caused by dried soap or dirt clogging the spout or the soap valve.TO
REMEDY: Clean spout with end of BobKey and/or flush the dispenser as described above.
5. Do not disassemble the soap valve. NOTE: If for any reason the valve becomes nonfunctional, a new soap valve replacement kit (Part No.
4112-79) must be ordered.
continued . . .
!
"
#
gg
MM
gg
MM
gg
MM
(Model B-2112 Shown)
B
C
A

REPLACEMENT PARTS LIST
Part Name Part No.
Valve Replacement Kit 4112-79
Collar Nut for Valve 4112-19
Window with O-Ring 2112-34
BobKey 24-17
VALVE REPLACEMENT INSTRUCTIONS
TO REMOVEVALVE:
1. Open filler-top by inserting BobKey (24-17) into slot of filler-top and then sliding latch to the left. Lift up filler-top.
2. Loosen locking-screw inside dispenser.Remove dispenser from wall and empty soap container.
3. Place 1" (25mm) closed-end wrench (provided) inside soap container and over the large collar nut at rear of soap valve and loosen until
face of valve can rotate.
4. While holding the collar nut in place with the wrench, unscrew soap valve from the front of
the unit by rotating counterclockwise.
TO INSTALL VALVE:
A. ON UNITS WITH ROUND HOLE IN SOAP CONTAINER
1. Pull back flat rubber washer at rear of soap valve face to expose the two plastic tabs.
2. Cut plastic tabs off rear of soap valve face flush with indicated surface (see Figure 4).
3. Move flat rubber washer back to its initial position. Make sure flat edge of washer is
even with the top of valve face.
4. Hold the collar nut with the 1" (25mm) closed-end wrench. Make sure the notch in the
collar nut is facing toward the front of the dispenser and position nut behind soap valve hole inside dispenser.
5. Screw new soap valve into collar nut, clockwise, until rear of valve face hits the front of the soap container. Adjust so that spout faces
downward.
6. Tighten collar nut with wrench until tight enough so that valve will not leak around seal at front of unit.
7. Install soap dispenser on wall bracket.
B. ON UNITS WITH NOTCHED SOAPVALVE HOLE IN CONTAINER
1. Hold the collar nut with the 1" (25mm) closed-end wrench. Make sure the notch in the collar nut is facing toward the front of the
dispenser and position nut behind soap valve hole inside dispenser.
2. Screw new soap valve into collar nut, clockwise, until rear of valve face hits the front of the soap container.
3. Push the soap valve into the soap container with valve tabs in the soap valve hole notches with spout facing downward.
4. Tighten collar nut with wrench until tight enough so that valve will not leak around seal at front of unit.
5. Install soap dispenser on wall bracket.
INSTRUCTIONS FOR INSTALLATION AND MAINTENANCE
Bobrick Classic™ Series Models B-2111 and B-2112 Surface-Mounted Soap Dispensers
3OAP#ONTAINER
3OAP6ALVE

#OLLAR.UT

7ALL0LATE
3CREW 7INDOW
WITH/2ING

"OB+EY

In the U.S.A.: BOBRICK WASHROOM EQUIPMENT, INC.
200 Commerce Drive, Clifton Park, New York 12065-1350 • Tel: [phone] • FAX: [phone]
11611 Hart Street, North Hollywood, California 91605-5882 • Tel: [phone] • FAX: [phone]
100 Bobrick Drive, Jackson, Tennessee 38301-5625 • Tel: [phone] • FAX: [phone]
In Canada:BOBRICKWASHROOM EQUIPMENT COMPANY
45 Rolark Drive, Scarborough, Ontario M1R 3B1 • Tel: [phone] • FAX: [phone]
© 2005 by Bobrick Washroom Equipment, Inc.
Form No. 2112-269 Revised 6/05 Printed in U.S.A.
FIGURE 4
0LASTIC4ABS
TOBE#UT/FF
&LUSHWITHTHIS3URFACE
0LASTIC4A B 
&LAT2UBBER7ASHER
MOVEDBACKTO
EXPOSEPLASTICTABS
WWW.BOBRICK.COM
BobKey