© 2011 by Bobrick Washroom Equipment, Inc.
Form No. 5050-69 r1/5/11 Printed in U.S.A.
In the U.S.A.: BOBRICK WASHROOM EQUIPMENT, INC.
200 Commerce Drive, Clifton Park, New York 12065-1350
s4ELs&!8
(ART3TREET.ORTH(OLLYWOOD#ALIFORNIA
s4ELs&!8
In Canada: BOBRICK WASHROOM EQUIPMENT COMPANY
2OLARK$RIVE3CARBOROUGH/NTARIO-2"
s/NTARIO%AST4EL&!8
s-ANITOBA7EST4EL&!8
INSTRUCTIONS FOR INSTALLATION AND MAINTENANCE
Bobrick Model B-5050 Soap Dispenser
#!4
!LLEN(EAD
3CREW
"OTTOM
-OUNTING4AB
+EY(OLE
3LOT
#ONTAINER
6ALVE!SSEMBLY
-OVEMENT
OF,ID
#!4
+EY3LOT
,ID
#!4+EY
HOW TO INSTALL THE DISPENSER:
1. Locate soap dispenser so the push button spout will be over the
LAVATORY!LLOWAMINIMUMMMCLEARANCEBETWEENTOPOF
dispenser and bottom of any shelf, cabinet, or other horizontal
PROJECTIONTOPROVIDEENOUGHSPACETOFULLYOPENTHELIDANDlLL
dispenser.
2. 2EMOVETHELIDWITHKEYPROVIDEDBYINSERTINGENDOFKEYINTOSLOT
at back of lid. Push key into slot and lift up the back of the lid at the
SAMETIME2OTATELIDFORWARDANDLIFTUPTOREMOVE
3. 0ROVIDEXXMMMOUNTINGSCREWS5SETHE
VESSELASATEMPLATETOMARKTHETHREEMOUNTINGHOLELOCATIONSON
THEWALL/NTHETOPHOLESUSETHESMALLENDOFTHEKEYHOLESLOTTO
MARKTHEHOLELOCATIONS$RILLMOUNTINGHOLES
4. 7ITHOUTTHEVESSELSCREWTHESCREWSINTOHOLESLEAVING
APPROXIMATELYMMBETWEENTHESCREWHEADANDTHEWALL
5. 0LACETHEBOTTOMMOUNTINGTABOFTHEVESSELOVERTHEBOTTOMMOUNTING
SCREW0LACETHELARGEENDOFTHEKEYHOLESLOTSATTHETOPOVERTHE
TWOMOUNTINGSCREWS2OTATETHETOPOFVESSELTOTHERIGHT4HISWILL
LOCATETHESMALLENDOFTHEKEYHOLESLOTSBEHINDTHEMOUNTINGSCREWS
&INALLYTIGHTENALLTHREESCREWSTOSECUREUNITTOWALL
The surface on which the unit is to be mounted determines the
specific type of mounting required for best installation:
For plaster or dry wall on studs,PROVIDECONCEALEDBACKINGANDSECURE
WALLBRACKETWITHSCREWS"ACKINGMUSTCOMPLYWITHLOCALBUILDING
codes.
For hollow tile partitions and other instances where applicable, provide
MMROUNDHEADTOGGLEBOLTS
For brick, concrete, or solid tile walls,PROVIDEMMlBERPLUGS
OREXPANSIONSHIELDSANDMOUNTINGSCREWSORPROVIDEMM
CINCHBOLTSOREXPANSIONBOLTS
For mirrors or glass surfaces, use the pressure-sensitive tape strips
provided. Do not use the tape for other types of wall surfaces. Clean
any dirt, dust, or oils from the surface and back of vessel. Apply both
tape strips horizontally on the back of the vessel. Press the vessel to
THELMIRROORGLASSSURFACE!LLOWTHETAPETOSETFORHOURSBEFORE
lLLINGTHESOAPVESSEL
HOW TO REFILL THE SOAP VESSEL:
1.2EMOVETHELIDWITHKEYPROVIDEDBYINSERTINGENDOFKEYINTOSLOTAND
LIFTINGUPTHEBACKOFTHELIDATTHESAMETIME2OTATELIDFORWARDAND
lift up to remove.
2. Filling soap vessel B-5050: Fill vessel with commercially marketed
all-purpose hand soaps.
3. Insert the tab on the front of lid into the recess inside the front of
VESSEL2OTATETHELIDTOWARDSTHEBACK0USHDOWNONTHEBACKOFTHE
lid to secure the latch on the lid into vessel.
MAINTENANCE:
1.7ARMWATERMIXEDWITHSOAPFROMDISPENSERISTHEBESTCLEANING
SOLUTIONFORALLSOAPDISPENSERPARTS0UMPWARMWATERTHROUGHTHE
vessel and valve periodically to flush out any contaminates or dried
soap residue. NEVER USE ABRASIVE CLEANERS.
2.0ERIODICALLYGIVETHEDISPENSERANOVERALLCLEANING2EMOVETHESOAP
VESSELBYlRSTREMOVINGTHELIDASDESCRIBEDEARLIER4HENLOOSENALL
THREEMOUNTINGSCREWSABOUTMM4HETOPOFVESSELMAY
THENBEROTATEDTOTHELEFT4HISWILLALLOWTHETOPOFTHEVESSELTOMOVE
SLIGHTLYFORWARDSOTHATTHEWHOLEVESSELMAYBELIFTEDUPFROMTHE
BOTTOMMOUNTINGSCREW
3.4HEVALVEASSEMBLYMAYBEREMOVEDFROMTHEVESSELBYREMOVING
the Allen screw from the bottom of the vessel. Do not disassemble
THEVALVEASSEMBLY./4%If for any reason the valve becomes
nonfunctional, a new Valve Assembly replacement kit (Part No.
5050-30) must be ordered. See replacement parts list.
4.7HENREPLACINGTHEVALVEASSEMBLYBESURETHECYLINDRICALHOLEINTHE
vessel is free from all debris and dried soap. Be sure to remove any
PLASTICTHATMAYHAVEBEENCREATEDBYTHREADINGTHE!LLENSCREWUP
into the bottom screw hole.
REPLACEMENT PARTS LIST
Part Name Part No.
Valve Assembly for B-5050 5050-30
INCLUDES!LLENWRENCH
,ID
0 0260 0
B-5050
QA010511
