Bosch D132A User manual

DETECTOR
+
DETECTOR
-
FIRE PT
+
FIRE PT
-
AUX PWR
+
AUX PWR
-
REVERSE
TRIGGER
TRBL PT
+
TRBL PT
-
R4
D132A
Smoke Detector Reversing Relay Module
D132A
en Installation manual

Smoke Detector Reversing Relay Module Notices | en 3
Bosch Securiity Systems, B.V. Installation manual 2019.08 | 05 | F.01U.069.463
1 Notices
These instructions cover the installation of the D132A Smoke Detector Reversing Relay
Module in a household fire system supervised by a fire alarm control panel (FACP) or a
combination Burglary/Fire control panel.
Before installing the module, become familiar with the Installation and Operation Guide for the
control panel you are using.
Install, test and maintain the module according to these instructions, NFPA 72, local codes,
and the authority having jurisdiction (AHJ). Failure to follow these instructions can result in
failure of a detector to initiate an alarm event. Bosch Security Systems, Inc. is not responsible
for improperly installed, tested or maintained devices.
!
Warning!
Follow these instructions to avoid personal injury and damage to equipment.
NFPA72 requires that you perform a complete system wide functional test following any
modifications, repair, upgrades or adjustments made to the system’s components, hardware,
wiring, programming and software/firmware.

4en | Description Smoke Detector Reversing Relay Module
2019.08 | 05 | F.01U.069.463 Installation manual Bosch Securiity Systems, B.V.
2 Description
This module allows compatible control panels (see the table below) to sound all smoke
detectors connected to point1 or zone1 when a single smoke detector on the loop goes into
alarm. To restore the smoke detectors to normal, reset the smoke detectors.
The following table lists control panels compatible with the D132A:
Control panels Compatible relays See section:
Active:
B Series panels1 ** D275, PAM-4 Wiring to a B Series panel,
page 8
D6412 and D4412 panels** Wiring to a D6412 or D4412
panel, page 13
G Series (GV2 and higher)
panels2
D275, PAM-4 Wiring to a G Series panel,
page 14
Legacy:
G Series (prior to GV2)
panels3
See control panel’s documentation on the Bosch website
(http://www.boschsecurity.com)
D9412, D7412, D7212**
panels
ICP-EZM2
D2812 panel**
D2412U and D2412UE
panels**
D2212, D2212B, and
D2212BE panels**
DS7240 and DS7220 panels**
1 B Series panels = B6512**, B5512**, B4512**, and B3512**
2 G Series (GV2 and higher) panels = B9512G, B8512G, GV4 (D9412GV4, D7412GV4, and
D7212GV4**), GV3 (D9412GV3, D7412GV3, and D7212GV3**), and GV2 (D9412GV2,
D7412GV2, and D7212GV2**)
3 G Series (prior to GV2) panels = D9412G, D7412G, D7212G**
** indicates products which are not UL listed for commercial fire applications

Smoke Detector Reversing Relay Module Description | en 5
Bosch Securiity Systems, B.V. Installation manual 2019.08 | 05 | F.01U.069.463
Figure2.1: D132A smoke detector reversing relay module
1 Mounting holes 6 Positive (+) power for module
2 Positive (+) to detector 7 Negative (-) power for module
3 Negative (-) to detector 8 Trigger to reverse detector power
Pull to GND to activate
4 Powered loop from control panel or
D125B
9 Positive (+) to trouble point
5 Powered loop from control panel or
D125B
10 Negative (-) to trouble point

6en | Installation Smoke Detector Reversing Relay Module
2019.08 | 05 | F.01U.069.463 Installation manual Bosch Securiity Systems, B.V.
3 Installation
1. Align the module with an available three-hole module mounting location in the enclosure.
2. Fasten the module to the enclosure with the three supplied screws.
For mounting locations inside the enclosure, see the control panel’s Installation Instructions.

Smoke Detector Reversing Relay Module Wiring | en 7
Bosch Securiity Systems, B.V. Installation manual 2019.08 | 05 | F.01U.069.463
4 Wiring
Use the table below to ensure you are using the proper wire gauge for the number of
detectors used and for the length of the detector circuit:
Number of
detectors
Maximum detector circuit length
22AWG
(0.34mm2)
20AWG
(0.5mm2)
18AWG
(0.75mm2)
16AWG
(1.5mm2)
1 935ft (285m) 1490ft (454m) 2370ft (722m) 3770ft (1149m)
2 935ft (285m) 1490ft (454m) 2370ft (722m) 3770ft (1149m)
3 465ft (142m) 745ft (227m) 1185ft (722m) 1885ft (575m)
4 310ft (95m) 495ft (150m) 790ft (241m) 1255ft (383m)
5 230ft (70m) 370ft (113m) 590ft (180m) 940ft (287m)
6 185ft (56m) 295ft (90m) 470ft (143m) 750ft (229m)
7 155ft (47m) 245ft (75m) 395ft (120m) 625ft (191m)
8 130ft (40m) 210ft (64m) 335ft (103m) 535ft (163m)
Notice!
To ensure system supervision, do not use looped wire under the terminals. Break the run to
provide supervision of the connections.
An external 12VDC or 24VDC power supply listed for fire signaling units and commercial or
residential burglary units can be used.
The external power supply must be UL1481 or UL864 Listed, regulated, and power‑limited.
Install the control panel and external power supply in the same room no more than 20ft (6m)
apart. The interconnecting wires between the control panel and external power supply must
be in conduit.
The power source for both the auxiliary power supply and the control panel must be from the
same dedicated AC branch circuit.

8en | Wiring Smoke Detector Reversing Relay Module
2019.08 | 05 | F.01U.069.463 Installation manual Bosch Securiity Systems, B.V.
4.1 Wiring to a B Series panel
4.1.1 Two-wire wiring for 12 VDC supplied by the control panel
Figure4.1: Two-wire wiring of D132A modules to a B Series control panel for power supplied by the panel
1 Detector loop (2‑wire) 9 Connection from D125B switch power
to control panel’s A output relay (NC).
Set the Output A jumper for AUX PWR.
2 EOL resistor 10 Connection for D125B Zone B to an
on-board point on the control panel
3 D132A module 11 Connection for D125B Zone A to an
on‑board point on the control panel
4 Connections for one D132A fire point
to D125B A loop
12 Connection from D125B Common
(either 4 or 5) to the control panel’s
common for the on‑board points
connected
5 Connections for the other D132A fire
point to D125B B loop
13 Earth Ground
6 Connection for AUX PWR - from D132A
modules to B-series panel COM
14 B Series control panel
7 Connection for AUX PWR + from
D132A modules to B-series panel AUX
15 D125B module
8 Connection from reverse trigger on
D132A modules to control panel B or C
output
Pull to GND to activate

Smoke Detector Reversing Relay Module Wiring | en 9
Bosch Securiity Systems, B.V. Installation manual 2019.08 | 05 | F.01U.069.463
Notice!
The illustration shows the D132A modules wired for both detector loops triggered by the
same output. For loops triggered by separate outputs, connect one D132A module reverse
trigger to B output and the other D132A revese trigger to C output.

10 en | Wiring Smoke Detector Reversing Relay Module
2019.08 | 05 | F.01U.069.463 Installation manual Bosch Securiity Systems, B.V.
4.1.2 Four-wire wiring for 12 VDC supplied by the control panel
Figure4.2: Four-wire wiring of D132A modules to a B Series control panel for 12 V power supplied by the panel
1 D132A module 9 D132A Trigger connection to panel’s
Output B or C
Pull to GND to activate
2 Resistor R4: for 4‑wire use, cut the
resistor leads to remove the resistor
10 Positive (+) trouble point connection
to an on‑board point on the control
panel
3 B Series control panel 11 Negative (-) trouble point connection
to an on‑board point on the control
panel
4 End-of-line (EOL) supervisory relay 12 EOL resistors
5 Positive (+) power connection to
detectors
13 Connections between an on‑board
point on the control panel , the
detectors (data lines), and the EOL
Supervision Relay
6 Negative (-) power connection to
detectors
14 First smoke detector on the detector
loop
7 Positive (+) fire point and AUX PWR
connection to panel’s AUX terminal
15 Last smoke detector on the detector
loop
8 Negative (-) fire point and AUX PWR
connection to panel’s COM terminal