Bosch B443 User manual

Conettix Cellular Communicators
B44x
en Installation Manual

Conettix Cellular Communicators Table of contents | en 3
Bosch Security Systems, Inc. Installation Manual 2018.04 | 02 | F.01U.345.070
Table of contents
1Cellular module introduction 4
1.1 About documentation 4
1.2 Bosch Security Systems, Inc. product manufacturing dates 4
2Component overview 5
3Installation 7
3.1 Insert the SIM card 7
3.2 Install the antenna 7
3.3 Install the communicator 8
3.4 Remove the communicator 10
4Diagnostic LED descriptions 11
5Configuration 12
5.1 Activating the B440-C/B441-C 12
6Specifications 13

4en | Cellular module introduction Conettix Cellular Communicators
2018.04 | 02 | F.01U.345.070 Installation Manual Bosch Security Systems, Inc.
1 Cellular module introduction
This document contains supplemental information needed to install the Conettix Plug-in
Cellular communication modules.
This reference guide contains:
– Component location overview.
– Installation workflows.
– Diagnostic LED descriptions.
– Configuration.
– Specifications.
1.1 About documentation
Copyright
This document is the intellectual property of Bosch Security Systems, Inc. and is protected by
copyright. All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.
1.2 Bosch Security Systems, Inc. product manufacturing dates
Use the serial number located on the product label and refer to the Bosch Security Systems,
Inc. website at http://www.boschsecurity.com/datecodes/.

Conettix Cellular Communicators Component overview | en 5
Bosch Security Systems, Inc. Installation Manual 2018.04 | 02 | F.01U.345.070
2 Component overview
Cellular plug-in communicators provide IP communications over supported cellular networks
by directly connecting the communicator into a control panel or into an additional module
such as the Conettix Plug-in Communicator Interface or the Conettix Universal Dual Path
Communicator modules. Some communicators come with a SIM card holder.
Communicators without SIM cards
12
3
4
5
1
Callout - Description
1 - Module handle and support leg
2 - LEDs
3 - Threaded female SMA antenna connector
4 - Plug-in module retention clip opening
5 - PCB metal contacts
Notice!
The B440-C/B441-C communicators must be activated and have a valid cellular plan for
proper usage. Refer to Activating the B440-C/B441-C, page 12 for details.

6en | Component overview Conettix Cellular Communicators
2018.04 | 02 | F.01U.345.070 Installation Manual Bosch Security Systems, Inc.
Communicators with SIM cards
23
4
5
6
1
1
Callout - Description
1 - Module handle and support leg
2 - SIM card holder
3 - LEDs
4 - Threaded female SMA antenna connector
5 - Plug-in module retention clip opening
6 - PCM metal contacts

Conettix Cellular Communicators Installation | en 7
Bosch Security Systems, Inc. Installation Manual 2018.04 | 02 | F.01U.345.070
3 Installation
When installing the communicator into a supporting module or control panel, refer to the
compatible documentation for more information.
!
Caution!
Remove all power (AC and battery) before making any connections. Failure to do so might
result in personal injury and/or equipment damage.
3.1 Insert the SIM card
Follow these instructions for SIM card installation.
1. Break away the SIM card from the die-cut.
2. Insert the SIM card into the SIM card holder by sliding it into the card holder.
3. Make sure the gold contact side of the SIM card is against the module.
Figure3.1: Inserting the SIM card
3.2 Install the antenna
1. Put the magnetic antenna on top of the enclosure, or vertically on another metal surface.
2. Put the antenna cable through a knockout.
3. Connect the antenna cable to the module.
4. Make sure the antenna cable is inside the enclosure.

8en | Installation Conettix Cellular Communicators
2018.04 | 02 | F.01U.345.070 Installation Manual Bosch Security Systems, Inc.
1
2
Figure3.2: Installing the antenna
Callout - Description
1 - Antenna routed through any knockout
2 - Antenna cable connected to the module
3.3 Install the communicator
Control panel/universal dual path communicator installation
1. Put the support leg into the support hole labeled X. Refer to Figure 3.3.
2. Align the PCB metal contacts with the on-board connector.
3. Push the module into place. The retention clip snaps closed and secures the module in
place.

Conettix Cellular Communicators Installation | en 9
Bosch Security Systems, Inc. Installation Manual 2018.04 | 02 | F.01U.345.070
1
3
2
Figure3.3: Communicator installation (B6512 control panel shown)
Callout - Description
1 - Support leg inserted into the compatible device support holes
2 - PCB metal contacts resting on the on-board connector
3 - Plug-in communicator retention clip
Plug-in communicator interface installation
1. Insert the communicator into the slot of the plug-in communicator interface.
2. Push in until you feel it "click" into place.
3
1
2
3
2
Figure3.4: Communicator installation (B450 shown)

10 en | Installation Conettix Cellular Communicators
2018.04 | 02 | F.01U.345.070 Installation Manual Bosch Security Systems, Inc.
Callout - Description
1 - SIM card insertion (if applicable)
2 - Communicator
3 - Plug-in communicator interface
3.4 Remove the communicator
1. Hold the plug-in module retention clip open.
2. Hold the top corners of the module support handle with your other hand.
3. Pull the module out.