brel-motors MGLE-45 User manual

Page 1
BREL motors is part of:
Manual Brel curtaintrack motor
Type MGLE-45
Read the manual before you begin the installation. If these instructions are not followed,
this may lead to defects and injury in which warranty can’t be claimed.
warning:
Children cannot recognize the dangers of electrical equipment and may therefore not work with it.
It is important to follow this instruction for your own safety.
1. Do not operate the motor in humid surroundings.
2. The motor must be installed correctly.
3. Keep the antenna in a good condition and do not shorten. The antennashould not come intocontact with other metal parts
otherwise it willreduce the effect.
4. The motor must be protected from direct moisture influences.
____________________________________________________________________________
Stop
Open------------- -----------Close
(This is a 2-channel transmitter,
Channel---------------- two P2 keys for each one channel)
P2 -------
P2 -------
_____________________________________________________________________________
Technical data of the motor Type MG45
Motor Voltage: 230V
Power: 45 Watt
Speed: 20 cm/sec
Max. curtain weight: 40 kg
Ampèrage 0.23 A
Max. duration: 4 min.
Moisture and dust: IP40
Working temperature of the motor:
oNormal use: -10℃tot +40℃
oHeavy use: -20℃tot +70℃

Page 2
______________________________________________________________________________
Functions Reach
L1 = 100 meter L2 = 25 meter
|---------------------------- LED
| |--------------------- P1 Programm button
------------------------- Connection for switch
_______________________________________________________________________________
Installation motor and rail
Attach the rail to the wall / ceiling.
Mount the rail not vertical.
If the motor don’t want to click easily, turn the gear wheel a bit and try again.
_______________________________________________________________________________
Charging the battery
When you use the battery for the first time, fully charge it. If the LED on the charger turns green, the battery is full.
Always use the charger type DC-216
_______________________________________________________________________________
Step 1 Setting up the first channel
Option A
1x P2 1x P2
OR
Turn the motor on. Press 1x on the Press 1x on the Press the open or closed button
The LED flashes. P2 button. P2 button. and the transmitter is ready for use.
The LED flashes. The LED flashes 5x.

Page 3
Option B
2 sec. 2x P2
OR
Press 2 sec. on P1. Press 2x on the The LED flashes 5x. Press the open or closed button
When LED flashes, P2 button, within and the transmitter is ready for use.
let go. 3 sec.
If the curtain is moving in the wrong direction, repeat the above procedure and then press close.
With the above action deletes all the channels in memory and the final adjustment.
______________________________________________________________________________
Step 2 Set or change preset position
If you press the Stop button longer than 3 sec., the motor will move to the preset position from any position.
1x P2 1x STOP 1x STOP
OK
Press 1x the P2 Press 1x stop button. Press 1x stop button. The position has now changed.
button. The LED flashes. The LED flashes.
To remove the preset position, you must go to the preset position and repeat above action.
_______________________________________________________________________________
Step 3 Delete transmitter
Deleting the transmitter can be done in three ways:
1. When setting up the first channel also the limit setup will be removed.
2.
Press P1 button until the LED flashes 2x and blinked 1x.
3.
1x P2 1x 1x P2
OK
Press P2 button 1x. Press close button. Press P2 button 1x.

Page 4
_______________________________________________________________________________
Step 4 Teaching multiple transmitters
2x P2 1x P2
Press P2 button 2x Press P2 button 1x Programming the new
of the existing transmitter. a of the new transmitter is ready.
transmitter or channel. b
To delete one channel , you must repeat the above operation.
_______________________________________________________________________________
Step 5 Setting the switch