brel-motors MJE24S User manual

Page 1
BREL motors is part of:
Manual Brel 24mm electronic DC radio motor single shaft
Type MJE24S
Read the manual before you begin the installation. If these instructions are not followed,
this may lead to defects and injury in which there can be no claim on the warranty.
warning:
Children cannot recognize the dangers of electrical equipment and may therefore not work with it.
It is important to follow this instruction for your own safety.
1. Do not operate the motor in humid environments.
2. The motor must be installed correctly.
3. Keep the antenna in a good condition and do not shorten. The antenna should not come intocontact with other metal parts
otherwise it will reduce the power.
4. The motor must be protected from direct moisture influences.
______________________________________________________________________________
(mode en time have only one function
at a transmitter with a timer: DC458 en DC 920)
Up P2 Mode P1
Channel - stop Channel + Time
Down
If you are using a multi-channel transmitter, you cannot program on the shared channel.
______________________________________________________________________________
Technical data of the motor Type MJE24S
•Motor Voltage: DC 12V
•Maximum ampère charger: 1.0 A
•Power: 6.8 Watt
•Torque: 0.6 Nm
•Speed: 34 rpm
•Ampèrage: 0.57 A
•Moisture and dust: IP40
•Storage capacity is up to 20 channels
•Working temperature of the motor:
oNormal use: -10℃tot +40℃
oHeavy use: -20℃tot +70℃

Page 2
______________________________________________________________________________
Installing the motor
Conus
Driveshaft
Wall mount
U-bar
Motor
U-plate
. Venetian
______________________________________________________________________________
Step 1 Setting up the first channel
The read-in of the first transmitter can be used in two ways:
1x
Option A 5 sec. 2x P2 1x
1x 2x The motor moves momentarily.
The direction of rotation
is right, go to step 3.
If the direction of rotation
Is wrong, go to step 2.
Put power on the motor, Press 2x P2 for 5 sec. Each time the motor Press the button up.
for example, by the battery. and release. moves momentarily.
The motor moves momentarily.
1x
Option B
5 sec. 2x P2 1x
1x 2x
The motor moves monetarily.
The direction of rotation
is right, go to step 3.
If the direction of rotation
Is wrong, go to step 2.
Press P1 1x and release when Press 2x P2 for 5 sec. The motor moves Press the button up.
the motor moves momentarily. and release. each time
. momentarily.
With the above action deletes all the channels in memory and the final adjustment.
You can also repeat this procedure to reset the motor.
______________________________________________________________________________
Step 2 Change direction
If the direction is right, skip step 2 and proceed to step 3.
Option A 5 sec.2x P2 1x
The direction of
rotation is right.
.
Put power on the motor, Press 2x P2 for 5 sec. The motor Press the button up.
for example, by the battery. and release. moves momentarily.
The motor moves 1x

Page 3
Option B
1x 1x 1x
The direction of
rotation is right.
.
Press P1 1x and release when Press the button up. The product goes down.
the product moves momentarily
after 3 sec. and again after 6 sec. 1x.
_______________________________________________________________________________
Step 3 Setting the end limits
1x P2 1x 1x P2 1x 
Press the P2 Press the button Press the P2 It moves momentarily. Set the product to the
button. The motor up. The motor button. desired upper position.
moves momentarily moves momentarily .
and beeps. and beeps.
STOP tot 1x STOP tot 
Hold the stop The product will move Set the product to the Hold the stop The product will
button until the motor up and down. desired lower position. button until the motor move up and
moves and beeps. moves and beeps. down.
Limit setting is right.
_______________________________________________________________________________
Step 4 paring new remote while maintaining end limits
1x P1
Press P1 and hold, until Press up and down buttons simultaneously, until
the motor moves up and down. the motor moves up and down.

Page 4
_______________________________________________________________________________
Step 5 Setting third limit position
If you press the stop button for more than 3 seconds, the motor will move from any position to the third limit position.
1x P2 2x STOP
Go to the desired Press 1x the P2 Press stop It moves momentarily.
third limit position button. button 2x. for confirmation.
To remove the third limit position, you must go to the third position and repeat above action.
_______________________________________________________________________________
Additional settings
Option A Delete limit position
Deleting the limit position can be done in two ways:
1. When setting up the first channel also the limit setup will be removed.
2. 1x P2 1x 1x P2
Each time you press a key you hear a beep.
The limit positions are now removed from the memory.
You can now re-read the limit position.
Press P2 button 1x. Press the button down. Press P2 button 1x.
_______________________________________________________________________________
Option B Teaching multiple transmitters (Up to 20 transmitters per receiver)
2x P2 1x P2
Press P2 button 2x Press P2 button 1x Programming the new
of the existing transmitter. of the new transmitter transmitter is ready.
or channel.
To delete one channel , you must repeat the above operation.
_______________________________________________________________________________
Option C Reset all
1x P2 1x STOP 1x P2
Press P2 button 1x Press stop button 1x Press P2 button 1x All channels are removed
_______________________________________________________________________________
Option D Pulse setting
1x 1x 1x
The motor is ready for use
Press P1 button 1x Press up button 1x Press down button 1x
To remove the pulse setting, repeat the above operation.