brel-motors MLE Series User manual

Page 1
BREL motors is part of:
Manual Brel Radio Tubular motor
Type MLE
Read the manual before you begin the installation. If these instructions are not followed,
this may lead to defects and injury in which warranty can’t be claimed.
warning:
Children cannot recognize the dangers of electrical equipment and may therefore not work with it.
It is important to follow this instruction for your own safety.
1. Do not operate the motor in humid surroundings.
2. The motor must be installed correctly.
3. Keep the antenna in a good condition and do not shorten. The antenna should not comeinto contact
with other metal parts otherwise it will reduce the effect.
4. The motor must be protected from direct moisture influences.
_______________________________________________________________________________
Functions remote control
Works with all BREL transmitters:
__________________________________________________________________________________
Technical data of the motor MLE15-0.3 MLE16-0.3 MLE25-1.1 MLE28-2 MLE35-3 MLE35-10
•Motor voltage: DC 8V DC 8V DC 8V DC 12V DC 12V DC 12V
•Charge voltage: DC 5V DC 5V DC 5V DC 5V DC 12.6V DC 12.6V
•Maximum ampere charger: 2 A 2 A 2 A 2 A 2 A 2 A
•Power: 5 W 3.6 W 8 W 15 W 26 W 26 W
•Torque: 0.3 Nm 0.3 Nm 1.1 Nm 2 Nm 3 Nm 10 Nm
•Speed: 30 rpm 50 rpm 28 rpm 28 rpm 28 rpm 9 rpm
•Amperage: 0.6 A 0.78 A 0.94 A 1.25 A 2.20 A 2.20 A
•Moisture and dust: IP44 IP44 IP44 IP44 IP44 IP44
•Storage capacity is up to 20 channels:
•Working temperature of the motor:
oHeavy use: -10℃tot +40℃
oNormal use: -20℃tot +70℃
______________________________________________________________________________
Reach L1 = 100 meter L2 = 25 meter

Page 2
If charging the MLE15, MLE25, only use a charger with Micro-USB plug (5V)
The battery is fully charged when the light stops blinking and lights-up continuously.
For charging in the UK the MLE16 and MLE28 and MLE35 only use the DC-213 ( 12.6V ).
For Europe use DC-212.
The battery is fully charged when the light on the charger DC-212/ DC-213 changes from red to blue.
Make sure that during installation the motor is sufficiently charged. Take care that the motor is not operated during charging.
_______________________________________________________________________________
Functions
MLE15, MLE25
Micro-USB-------- Antenne------- Antenne------
Micro-USB-----
P1 ------------------ MLE25 MLE15
On/off button -------- MLE15
P1 button -------------
Note: Take away the plastic cover to connect the micro-USB plug to the motor. Charging plug ---------- MLE16
MLE16 and MLE28 and MLE35
Charging plug --------------- Charging plug ------------ Antenna ------------------
P1 button ------------------------- Antenna --------------
MLE35 MLE28
P1 ----
Antenna ------------------
_______________________________________________________________________________
Installing the motor
Attach the crown and wheel to the motor and place the clip on the shaft of the motor so that the wheel
is fixed to the motor.
Install the motor with the motorbracket on the product and take care that it is secured.
Place the motor in the tube of the roller/shutter.
(These assemblies are usually already done in the factory) During programming the motor;
the following must be done within 10sec. After 10 sec. the motor will quit the programming mode.
EMERGENCY CONTROL: If a transmitter has been paired and the end positions determined in the motor,
you can use the P1 key as the control key.
NOTE: The MLE15 and MLE 16 does not beep.
_______________________________________________________________________________
Step 1 Setting up the first channel
Press P1 until 1x 2x P2 1x The direction of
rotation is right.
Go to setting the
. end position.
Go to step 3.
The direction of
rotation is wrong.
Go to step 2.
Hold down the P1 button until the motor Press 2x on the Press the button up.
moves momentarily (and beeps). P2 button. Each The motor moves.
time you press the
button, it moves
momentarily (and beeps}
With the above action you will delete all channels in memory and the final setting.

Page 3
______________________________________________________________________________
Step 2 Change direction
Variant A If the direction is right, skip step 2 and proceed to step 3.
Press P1 until 1x 2x P2 1x 1x 
Hold down the P1 button until the motor Press 2x on the P2 button. Press the button down. Press the button up. The product will now go up.
moves 2x momentarily (and beeps). Each time you press the The motor moves. Reading the first transmitter
button, it moves momentarily. (At the end you will has been completed. You
(and beeps). hear 6 beeps). can now proceed with
setting the end limits.
Variant B
Press P1 until 3x
Hold down the P1 button until the motor The direction of rotation is changed.
moves 3x momentarily (and beeps).
_______________________________________________________________________________
Step 3 Setting the end limits If no limit positions are set, the motor will only move in the pulse setting.
1x P2 1x 1x P2 1x
Press the P2 Press the button Press the P2 It moves momentarily. Set the product on the
button. The motor up. The motor button. desired top position.
moves momentarily moves momentarily The motor .
(and beeps). (and beeps). (beeps 4x).
STOP until  1x STOP until
Hold the stop button until the motor Set the product on the end position. Hold the stop button until the motor moves
moves momentarily (and beeps). momentarily (and beeps). Limit setting is ok.
_______________________________________________________________________________
Step 4 Setting third limit position
If you press the stop button for more than 3 seconds, the motor will move from any position to the third limit position.
1x P2 2x STOP 
Go to the desired Press 1x the P2 Press stop It moves momentarily.
third limit position button. button 2x. for confirmation.
To remove the third limit position, you must go to the third position and repeat above action.

Page 4
_______________________________________________________________________________
Additional settings
Option A Delete limit position
Deleting the limit position can be done in two ways:
1. When step 1, setting up the first channel also the limit setup will be removed.
2. 1x P2 1x 1x P2
Each time you press a key you hear a beep.
The limit positions are now removed from the memory.
You can now re-read the limit position.
Press P2 button 1x. Press the button down. Press P2 button 1x.
(The motor beeps 1x). (The motor beeps 1x). (The motor beeps 4x).
_______________________________________________________________________________
Option B Teaching multiple transmitters (Up to 20 transmitters per receiver)
2x P2 1x P2 
Press P2 button 2x Go to new channel or transmitter b/ Programming the new
Go to existing channel / transmitter a. of the existing (to remove channel / transmitter) transmitter/channel is ready.
channel / transmitter a. Press 1x P2 button of the new
channel or transmitter b.
To delete one channel , you must repeat the above operation.
_______________________________________________________________________________
Option C Delete all
1x P2 1x STOP 1x P2
Press P2 button 1x Press stop button 1x Press P2 button 1x All channels are removed
(The motor beeps 1x). (The motor beeps 1x). (The motor beeps 5x).
_______________________________________________________________________________
Option D Pulse setting
1x P2 1x 1x
Press P1 button 1x Press up button 1x Press down button 1x
(The motor beeps 1x). (The motor beeps 1x). (The motor beeps 2x).
To remove the pulse setting, repeat the above operation.
_______________________________________________________________________________
Option E Pairing new remote while maintaining end limits. Only possible if the end limit is set.
Press P1 until 1x  simultaneously
Press P1 and hold, until the motor moves up and down (beeps). Press up and down buttons simultaneously,
until the motor moves up and down (beeps 2x).

Page 5
_______________________________________________________________________________
Option F Speed control
- Increase the speed of the motor. - Reduce the speed of the motor.
+ STOP simultaneously  +STOP simultaneously 
OK OK
Push up and stop simultaneously, until the motor moves. Press down and stop simultaneously, until the motor moves.
If the motor is not moving, it is already in the highest or lowest speed.
There are 3 different speeds; Namely: 24 rpm ➔ 1x - 28 rpm ➔ 2x - 32 rpm ➔ 3x.
_______________________________________________________________________________
Option G Reset everything
Press P1 until 4x
Press P1 and hold, until the motor moves up and down 4x.
_______________________________________________________________________________
Option H Adjusting the top position
1x simultaneously  STOP until 
OK
Go to the already set top position. Press simultaneously the button up The motor moves up and down. Hold the stop button until the
and the down button until the motor moves. Go to the new upper position. motor moves momentarily.
(The motor beeps 4x). ( The motor beeps 1x).
_______________________________________________________________________________
Adjusting the bottom position
1x simultaneously  STOP until 
OK
Go to the already set bottom position. Press simultaneously the button down The motor moves up and down. Hold the stop button until the
and the up button until the motor moves. Go to the new upper position. motor moves momentarily.
_______________________________________________________________________________
Option I Disable receiver
Press P1 until 2ex  1x P1
The receiver
is turned off.
Hold down the P1 until the motor moves for the 2etime up and down. Press the P1 1x to reactivate the receiver.