Bretford EXPLORE User manual

EXPLORE®4-Leg Teaming Table
with Screen Share
Assembly Instructions
This product includes electronic hardware and should be installed by a qualied individual.
Installation time of 4 hours or more for this table should be expected.
Two people are suggested when setting the angle and position of your monitor.
Monitor Display Requirements: your at panel display must conrm to the following
requirements.
yWith the stand removed, the monitor must not exceed 40 lbs.
yFeature a mounting hole pattern 200mm x 200mm or smaller.
yHDMI input with native resolution of 1080p.
yReturn to the last HDMI input programmed when powered on.
ySleep mode must be disabled to use the Power Controller.
yTeaming Table with Screen Share is optimized to mount monitors up to 40” but can
accommodate a larger display as long as it meets the above specications. Always check
monitor specications before purchasing your display.
Bretford provides some Allen wrenches required for assembly but you will need the
following tools to complete your installation.
yPhillips screw driver with large head
yPhillips screw driver with small head
yWire cutters
yWire strippers
yScissors

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
2
Wood Top - Qty 1
(Part number varies by model number)
Top Stiffener - Qty 2
60” & 72”= 017-0519, 84”= 017-1191
Cord Bin - Qty 1
60”= 060-1126, 72” & 84”= 060-1127
FPP1M0 - Qty 1
Low prole vesa mount
010-6386 - Qty 1
Transition mounting plate
010-4381 - Qty 1
Steel Plate
017-1170 - Qty 4
Lower Leg
022-3203 - Qty 4
Upper Leg
010-4889 - Qty 1
28” Pole
015-0175 - Qty 4
2 1/2” Stem Caster w/Brake
(Comes Installed into Lower Legs)
012-0753 - Qty 1
Pole Cap
012-0761 - Qty 2
Plastic Cord Clip
015-0045 - Qty 4
Threaded Glide

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
3
030-0354 - Qty 4or 6
10-32 x 1 1/2” L
Button Socket Screw
(60” & 72” = 4, 84”= 6)
030-0396 - Qty 8
3/8-16 x 1/2”
Socket Set Screw
030-0402 - Qty 10
#10-32 x 5/8”L
Combo Screw
030-1128 - Qty 4
1/4-20 UNC, 1 3/4”L
Socket Hd Screw
SC1054 - Qty 28
1/4-20 x 3/4”L
Philips Screw
030-1267 - Qty 4
M4 Nut
030-1234 - Qty 4
M4 x 0.7, 12 mm Long
Pan Head Screw
030-0397 - Qty 1
3/16” Allen Wrench
030-1237 - Qty 1
1/2” Allen Wrench
HK 1020 - Qty 1
5/32” Allen Wrench
030-0353 - Qty 1
1/8” Allen Wrench
030-1129 - Qty 1
5/8-11 UNC, 1 3/4”L
Socket Head Screw
030-1806 - Qty 2
Hook
Part No Description Quantity
012-0991 Leg Cord Management Clip 1
030-1762 Velcro Strips 4
044-2124 Display Courtesy Hardware Pack 1
Display hardware
pack Contents
Metric M4x12 screws 4
Metric M4x30 screws 4
Metric M5x12 screws 4
Metric M5x30 screws 4
Metric M6x12 screws 4
Metric M6x35 screws 4
Small washers 8
Large washers 20
5/8” Large spacers 4

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
4
Part Number Description Quantity
EXTRON X42 Package Kit
010-6921 Controller Bracket MBU123 1
010-6922 Switch Bracket MBU125 1
018-0695 2-Outlet Power Unit 2
018-0691 X42 Controller 1
018-0694 X42 HDMI/VGA Switch 1
018-0688 Cable Cubby 1400 1
023-1005 HDMI Ultra 12’ Cable 1
023-1006 HDMI “Show Me” Cable, 6’ 4
023-1008 VGA “Show Me” Cable, 6’ 2
023-1009 X42 Control Cable 1
080-1001 Extron Installation Guide - X42 1
EXTRON X60 Package Kit
010-6923 Controller Bracket MBU149 1
010-6922 Switch Bracket MBU125 1
018-0695 2-Outlet Power Unit 2
018-0690 X60 Controller 1
018-0693 X60 HDMI Switch 1
018-0688 Cable Cubby 1400 1
023-1005 HDMI Ultra 12’ Cable 1
023-1006 HDMI “Show Me” Cable, 6’ 6
023-1007 X40/60 RS232 Control Cable 1
080-1000 Extron Installation Guide - X40 & X60 1
EXTRON X40 Package Kit
010-6921 Controller Bracket MBU123 1
010-6922 Switch Bracket MBU125 1
018-0695 2-Outlet Power Unit 2
018-0689 X40 Controller 1
018-0692 X40 HDMI Switch 1
018-0688 Cable Cubby 1400 1
023-1005 HDMI Ultra 12’ Cable 1
023-1006 HDMI “Show Me” Cable, 6’ 4
023-1007 X40/60 RS232 Control Cable 1
080-1000 Extron Installation Guide - X40 & X60 1
Extron Screen Share Electronic Component Inventory

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
5
030-0354
(4)X
017-0519
(2)X
1

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
6
022-3203
(1) 4X SC1054
(7) 4X
2

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
7
015-0045
(4)X
017-1170
(4)X
3
For glide version tables only.
Skip this step if your table has casters.

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
8
Height Adjustment
Holes
030-0396
(2) 4X
Set screws are pre-installed in
your upper legs and need only be
loosened to insert lower leg section.
Tables using glides are height
adjustable from 20” to 30” at time
of assembly. Tables using casters
are height adjustable from 22” to
32” at time of assembly.
4

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
9
010-4889
(1)X
End with threaded
holes should face down
towards table surface.
010-4381
(1)X
030-1128
(4)X
030-1129
(1)X
5

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
10
This step is only for monitors that use a 200mm x
100mm or 200mm x 200mm mounting hole pattern.
FPP1M0
(1)X
030-1234
(4)x
030-1267
(4)x
To secure the mounting plate to the back of your monitor, a courtesy hardware pack (#044-2124)
has been provided with several metric screw sizes. You may need to purchase additional metric
screws from your local hardware store for a monitor with different mounting screw size.
Optimized for at panels up to 40” with no larger than a 200mm X 200mm mounting hole pattern.
The mount can accommodate a larger monitor as long as it meets the specications on the rst
page. Monitor weight may not exceed 40 lbs.
6

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
11
Follow this step for monitors that use a 200mm x
100mm or 200mm x 200mm mounting hole pattern.
Follow this step for monitors that use a 100mm x
100mm mounting hole pattern.
Screws provided
in courtesy
hardware pack
#044-2124.
Longer M4 screws are
available in the courtesy
hardware pack if required.
030-1234
(4)x
7

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
12
Quick release lever – Pull out
to insert into tube and adjust
monitor mount height.
Loosen screws prior to entry.
Tighten to secure in place.
For stability, Monitor mount must
install facing the work surface.
Monitor not
shown for
clarity
With someone’s help, slide the monitor mount
assembly into the pole. NOTE: Make sure
the screws in the spike are loosened and the
release lever is pulled out while sliding in the
spike. Once desired location is determined,
tighten spike screws.
8

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
13
Position your monitor to be horizontal with
the table top. Using a 1/8” Allen wrench
provided, tighten the set screw to prevent
rotational swivel.
Two people are suggested when setting the
angle and position of your monitor.
Position your monitor at the desired angle.
Using a 3/16” Allen wrench provided, tighten
the large bolt to maintain the monitor tilt
position.
012-0753
(1)X
9

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
14
Install the two 2-outlet power modules into the Cable Cubby using the lock washers, black screws,
and small screw driver provided by Extron. Bretford recommends you install them to the middle
height setting. Install one power unit for each Cable Cubby door and install both so they are closest
to the monitor.
TIP: Keep power cords secured with the twist ties until the cord bin is lifted into place.
Both power modules mount close to the monitor.
10
ISOMETRIC VIEW

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
15
Insert the Show Me cables into the plastic plates, half in the 1st plate and half in the 2nd plate. Show
Me cable buttons need to be above the plastic plate. Keep the twist tie on the lower portion of Show
Me cable in place at this time. Using the black screws provided by Extron, secure the plate to the top
of the small aluminum sleeves.
Fill unused holes in the plastic
cable plate with the plastic buttons
provided.
There are four aluminum sleeves, use the
shorter aluminum sleeves and discard the
longer pair.
11
12

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
16
Feed the assembly up through the bottom of the Cable Cubby and secure in place at the lowest
position using the lock washers and black screws provided by Extron.
13
ISOMETRIC VIEW

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
17
018-0688
(1)X
Move the latch brackets on the sides of the Cable Cubby down to the lowest
position with the levers pointing down. Rotate them at against the cubby wall.
Keeping the power outlets closest to the monitor mount, feed the cables
through the table opening and place the Cable Cubby into the table.
Slide the latch brackets up until
they are snug to the underside of
the work surface and lift the lever
upward to lock into place.
14

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
18
Attach the mounting brackets to your TeamWork Switch. The X40 (TeamWork 400) 4 user HDMI
switch utilizes Extron mounting brackets MBU123; The X60 (TeamWork 600) 6-user HDMI switch
utilizes Extron mounting brackets MBU149; The X42 (TeamWork 601) 6-user (4)HDMI/(2)VGA switch
utilizes Extron mounting brackets MBU123.
Install the rubber bumpers provided
by Extron to the top of the TeamWork
Switch.
15
16

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
19
Strip approximately 1” of the black cover off of the short extension from each of the Show Me cables.
Expose and separate the Red, Black and bare wires as shown.
17

EXPLORE 4-Leg Teaming Tables with Screen Share
Assembly Instructions
20
+V
2
C G TC G TC G T
46
1 3 5
Tx Rx G
C G TC G TC G T
+V
2
C G TC G TC G T
46
1 3
CONTACT IN/TALLY OUT
Tx
G
5
T Rx G
C CC T G G T
+V
RS-232
For switches using both HDMI and VGA connections,
(versions X42) the Red hot wire attaches to the left
position marked “C” on the back of the switch and the
Black ground wire attaches to the right position marked
“T”. Bare wire is not used.
Using the small screwdriver provided, tighten the tally
port screws to each wire and secure the cables into
place using the thin white cable ties provided.
X42 four user switch
Connect each wire to the blue tally ports attached to the back of the TeamWork switch. For switches
using only HDMI connections, (versions X40 and X60) the Red hot wire attaches to the port marked
“Contact” on the back of the switch and the Black ground wire attaches to the port marked “Tally Out”.
Bare wire is not used.
18
Tx Rx
RS-232 AUTO
CONTACT
1 2 +V
1 2 G
TALLY OUT
3 4
3 4 Tx G
RS-232 AUTO
Rx
1 2 3 4G56G
1 2 3 4 +V 5 6+V
CONTACT
TALLYOUT
SW6 HDMI
X40 four user switch X60 four user switch