Bretford TechGuard Connect User manual

TechGuard™Charging Locker 10-Bay
Assembly & Installation
|The equipment is to be secured to the building structure before
operation.
|Consult with a structural engineer or suitable professional prior to
installation.
|Unit must be secured to oor and/or anchored to the wall in compliance with
local building code.
|Two people required for lifting during assembly.
|Nothing may be placed on top of assembled unit.
|The socket-outlet shall be installed near the equipment and shall be easily accessible.
|Installation Instruction states the product is to be secured to building before operation.
|Elevated Operating Ambient - Consideration should be given to installing the lockers in an
environment compatible with the maximum ambient temperature Tma of 40°C.
|Reduced Air Flow - Instructions indicated to not block the ventilation openings so proper air ow
required for safe operation of the equipment is not compromised.
|Mechanical Loading - Mounting of the equipment in the locker should be such that a hazardous
condition is not achieved due to uneven mechanical loading.
TechGuard Charging Locker 10-Bay 031-10478 Rev 1.0
Tools Required Estimated Time Required People Required
T-25 Bit
30 Min. Two (2)
Bubble Level
Powered or Manual Bit Driver
Bit Extension

TechGuard Charging Locker 10-Bay 031-10478 Rev 1.0
Assembly Instructions
2
010-6980 - Qty 1
Top Cap
017-1292 - Qty 4
Short Support Tube
010-6983 - Qty 2
Front & Back Panel
010-6981 - Qty 2
Side Panel
022-3582 - Qty 1
Stacking Bracket
017-1293 - Qty 2
Long Support Tube
015-0045 - Qty 4
Leveler Foot
030-1796 - Qty 12
#10-32 x 1/2” Serrated Screw
010-7152 - Qty 1
Wall Anchor Bracket

TechGuard Charging Locker 10-Bay 031-10478 Rev 1.0
Assembly Instructions
3
1
Pedestal Assembly
2
030-1796
(8)x
017-1293
(2)x
017-1292
(2)x
017-1292
(2)x
030-1796
(8)x

TechGuard Charging Locker 10-Bay 031-10478 Rev 1.0
Assembly Instructions
4
3
4
015-0045
(4)x
010-6980
(1)x
030-1796
(8)x
Route all power cords
through Top Cap prior to
attaching Top Cap to tube
frame.
Adjust leveler feet to
desired location (use
bubble level).

TechGuard Charging Locker 10-Bay 031-10478 Rev 1.0
Assembly Instructions
5
5
6
010-6981
(2)x
030-1796
(8)x
Front
Back
Pedestal Mount To 5-Bay Locker
Carefully place 5-bay onto
pedestal.

TechGuard Charging Locker 10-Bay 031-10478 Rev 1.0
Assembly Instructions
6
Bottom view
Bottom view
Hold unit in place while
afxing unit to pedestal
with four (4) supplied 10-32
screws, being careful not to
overtighten.
The pedestal must be attached
to oor as necessary - consult
with a structural engineer
or suitable professional to
determine requirements.
There are four (4) holes,
5/8” (15.8mm) diameter in
the Short Support Tubes
of the pedestal.
030-1796
(4)x
7

TechGuard Charging Locker 10-Bay 031-10478 Rev 1.0
Assembly Instructions
7
8
030-1796
(4)x
022-3582
(1)x
Stack 5-Bay With Another 5-Bay Locker
Route power cord through appropriate hole if desired and attach stacking bracket to underside of upper
5-bay using four (4) supplied 10-32 screws, being careful not to overtighten.
Upper 5-Bay unit may be placed in any orientation (90, 180, 270 degrees) from lower 5-Bay unit,
as desired.

TechGuard Charging Locker 10-Bay 031-10478 Rev 1.0
Assembly Instructions
8
9
030-1796
(4)x

TechGuard Charging Locker 10-Bay 031-10478 Rev 1.0
Assembly Instructions
9
1. Locate the Y-Connector power cable and feed it through the
opening for the back panel. (You may need to re-adjust the
Leveler Feet of the base to accommodate the Y-Connector
cable.)
2. Connect each power cable to the supplied Y-Connector cable.
3. Connect the Y-Connector cable to a dedicated 15 A wall outlet.
10
To 15 A wall outlet

TechGuard Charging Locker 10-Bay 031-10478 Rev 1.0
Assembly Instructions
10
Secure the Wall Anchor Bracket
to the wall if desired.
11
030-1796
(2)x
010-7152
(1)x