Bristan HOU 1HBF C Wiring diagram

Installation Instructions
& User Guide
Please leave these instructions
with the end user
Pack Contents
Specifications
Dynamic Water Pressure
Maximum Static Pressure: 10.0 bar
Min: 1.0 bar Max: 5.0 bar
Adjustable Spanner
0
1.0
2.0
5.0
4.0
3.0
Pressure
BAR
Inlet Water Temperature Inlet Connections
Operation
22mm Compression
Flexible Tails
60°C
Maximum Hot 60°C
HOU 1HBF C (D4)
Hexagonal Keys Box Spanner
(cartridge)
2.5mm 30mm
Box Spanner
(fixing rod nut)
9mm
Tools Required for Installation/ Maintenance
Outlet
Housed M24
Flow Straightener
To replace any spare parts
for your tap, why not
scan the QR Code or
visit www.bristan.com
and search for your
product.
All products manufactured and supplied by Bristan are safe to use provided that they are installed, operated and
receive regular maintenance in accordance with these instructions.
This product needs to be installed in accordance with, and meet the requirements of The Water Supply (Water
Fittings) Regulations (Northern Ireland) 2009 and The Water Supply (Water Fittings) (Scotland) Byelaws 2014.
For full Installation Requirements & Notes (IRN) please visit www.wrasapprovals.co.uk/approvals-directory
Isolation valves must be fitted to the inlet water supplies to ensure ease of future maintenance.
Before installing this product the water supply must be thoroughly flushed in order to remove any swarf, solder etc.
Full access must be made available for future maintenance/servicing purposes.
This product must not be modified in any way as this will invalidate the guarantee.
Prior to Installation Spare Parts
x1
x1
x1
x1
x2
Tap Body
Base Seal
Fixing Kit
Hex Key
Flexible Tails On
Hot
Cold
Size 1
Cross Head
Screwdriver

2*
1Look underneath the
tap body to observe
fixing kit rod(s) and
tail inlet positions
Depending on the model, the tap will utilise 1 or 2
fixing kit rods. Refer to your contents page
Screw in the fixing kit
rod(s) into the base of the
tap with a screwdriver
Screw in the
flexible tails by
hand only.
DO NOT
OVERTIGHTEN
If required, thread
the flexible tails
and fixing kit rods
through the plinth
and rubber seal
(if loose) and align
with tap body
Thread the flexible
tails and fixing kit rods
through the bath hole
If the hole is not
large enough for
both tail ends to
fit through,
screw one of the
tails in from
underneath the
bath
4
From underneath the bath,
slide the rubber gasket and
metal c plate along the
fixing rod(s) with the
gasket sitting on top of
the c plate
You can screw
the nut by hand
and tighten with
a box spanner
once at the top
1 Fixing Rod 2 Fixing Rods
Fixing
Rod Hole
Flexi Tails
Holes
Flexi Tails
Holes
Fixing
Rod Hole
Fixing
Rod Hole
Align the gasket and c plate, then
begin tightening the nut up the rod
towards the bath until secure
Your model may come
with a plinth and will
either be included
pre-attached or loose in
the box*
Important
The images shown are for
illustrative purposes only.
The tap you have purchased may
look dierent to those pictured in
this booklet but will follow the same
installation steps.
Your contents page will be specific
to your product.
If you find your product or any of
its components dier from those
shown on the contents page, please
contact our customer support.
Installation
2
3
Take note of any grub
screw holes on the
underside of the tap and
align them correctly to
the holes on the plinth

Connect the hot
and cold water
supplies to the
flexible tails and
turn until tight
Hot on the
left, cold on
the right.
5
Your tap is now ready
for use
IMPORTANT
Turn on water
supply for a few
minutes and check
all joints and
connections for
any leaks.
1 2
3
Fit the waste above the bath
ensuring the washer is in place
Push waste into hole
until the outer rim sits
flush with the bottom
of the bath.
Push the centre down to close the waste Bristan products are made from premium
materials, with hand polished, electroplated, PVD
or EPD finishes.
Your taps or shower should be regularly cleaned
with warm water, a mild pH-neutral liquid soap,
and polished with a soft cloth. Any residues from
soap, toothpaste, shampoos and shower gels can
cause blemishes if not rinsed o straight after
use.
Household bleaches and cleaners contain harsh
chemicals and may damage the surface
finish. Avoid using abrasive cloths, scouring pads,
scrub sponges, steel wool or anything similar.
6
Then place the washer
from underneath and
tighten the backnut to
secure the waste
to the bath.
Slight
bend
90 °
angle
Kinks
Curved
round Twists
REMEMBER
Refer to the
next panel for
correct flexible
tail positions
Push again to open and release the
contents of the bath.
Your waste is now
ready for use
Waste Installation and Operation
General Cleaning

Remove indice by pulling it
loose, then undo hex grub
screw to remove handle
Remove
the shroud and
retaining nut and
then lift the
cartridge out of
the tap
(Some shrouds
may need to be
unscrewed by hand
before removing)
13
12
Reverse the steps to
replace the
cartridges/ valves
and handles.
2
Using a box
spanner will
ensure that you
can reach the
retaining nut if it
recessed into the
tap body
(Grub screw
will be located
at the front
or rear of the
handle)
Maintenance - Cartridge/ Valve Replacement
Isolate the
water supply
before
starting!
IMPORTANT
Check all loose
parts for any
damage, then soak
using a suitable
solution to de-scale
3Reverse the steps to
replace the outlet
12
If provided, insert
the key tool into
the outlet and twist
to release it
Using a coin, insert
into the slot on the
outlet and twist to
release it
Using an
adjustable spanner,
unscrew gently to
remove the outlet
Housed Outlet
1a
2
Recessed Outlet
Coin Slot Outlet
1c
1b
IMPORTANT
Refer to your
contents page to
see what outlet
your model has
Bristan oers an eective
chrome-friendly cleaning kit for
use with your taps and showers.
Scan the QR Code or search for
‘CLEAN KIT01’ on
www.bristan.com.
Love Your Chrome
Maintenance - Clean/ Replace Outlet

Symptom Cause Remedy
Low Flow
Partially closed isolation valve. Open isolation valve.
Airlock or partial blockage in the supply
pipework.
Flush through pipework to ensure removal of
debris and any airlocks.
Partial blockage in the outlet Remove to Clean and soak in suitable
solution.
No hot water or
cycling hot and
cold
Instantaneous water heater cycles on
and o as flow rate or pressure is too
low.
Increase water flow rate or pressure through
system.
No Flow Closed isolation valve. Open isolation valve.
Mains water supply turned o. Turn on mains water supply.
Temperatures not
corresponding
with taps
Inlet pipes have been connected
incorrectly
Swap the inlet tails around.
Troubleshooting
Notes
Please use this space for any notes you
or your installer may have regarding the
installation/plumbing of this product.
At Bristan, we want to make things as easy as possible for our customers. That’s why we oer
solid guarantees on all our products, eective from the date of purchase, to give you peace of mind.
Your guarantee starts from the purchase of your product, but you can still benefit from registering it for
easier identification in the unlikely event of a manufacturing fault, please visit www.bristan.com/register
For any other queries, please call Customer Service on 0330 026 6273 where our expert team
of advisors will be able to oer you any help and advice.
For full guarantee terms and conditions visit www.bristan.com/service-centre/guarantees.
Our Guarantee
Bristan Group Ltd.
UK: Bristan Group, B78 1SG.
EU: Masco Europe S.à.r.l.
14 Rue Strachen
6933 Mensdorf
Luxembourg
Customer Service: [phone]
Web: www.bristan.com
Email: [e-mail]
A Masco Company
Contact Us
Servicing Your Tap
We recommend servicing your tap at
least once every year to prolong its life.
To see a video showing how to remove
the cartridge for servicing, scan the QR
code with your smart phone or tablet.
Alternatively visit www.youtube.com/
BristanTV