Brita RF-103 User manual

Version 1.0E
RF-103
Installation
Instructions
Step 1
Step 2
Step 3
As Easy As...
REFRIGERATOR
Inline
Extended Life
Refrigerator/
Icemaker Filter
Connects To Incoming
Water Line
Front View Back View
System Tested and Certied by NSF
International against NSF/ANSI 42 and 372
for the reduction of the claims specied on
the Performance Data Sheet.
Inline Extended Life Refrigerator/Icemaker
Filter Model RF-103

2
Tools & Materials Required
Inline Extended Life
Refrigerator/Icemaker
Filter
main:
tools needed for installation
hacksaw
pipe cutter (for copper
pipe installation)
shut o valve
saddle top valve with
shut o
1/4" plastic tubing
package contents
optional items
utility knife
tape measure
safety glasses
filter and fittings
bucket
bucket
Filter Model No. Date Purchased / Date to Replace For FREE Filter Replacement
Reminder, go to
www.protectplus.com
My BritaUniversal Filtration System (Replace filter every 5 years)
Internet & Mobile[phone] Free Installation Video
Manufactured for: Protect Plus, LLC 420 3rd Avenue NW, Hickory, NC 28601 USA
fitting
fitting
1/4" Adapter Fittings
1 2 3
30’

3
RF-103 installation instructions Version 1.0E
Before You Begin
WARNING: Be sure that all electrical appliances and outlets are turned o at the circuit breaker before installing with this filter.
WARNING
Operation / Maintenance Data
These units are intended for non-commercial use. They should be used only in ambient air temperature of between 40 degrees F /
4.4 degrees C and 100 degrees F / 37.7 degrees C. Placement of these units in direct sunlight or use of electrical heating equipment
on these units must be avoided. Replace filter cartridge when and as directed in the installation /operation instructions included with
each cartridge. Replacement filter cartridges are available at retail outlets.
• These filters are not water purifiers. Do not use with water that is microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system.
• This unit is not designed to filter sulfur odor (rotten egg odor) caused by hydrogen sulfide. Use of carbon filters to treat sulfur odor
may intensify taste/odor problems.
• Please comply with all state and local regulations regarding the installation of water treatment devices.
• The contaminants or other substances reduced by the water filter device are not necessarily in your water.
Filtration Facts
Please read all instructions, specifications, and precautions before
installing and using your water filter system.
NOTICE
Precautions: for cold water use only.
Before installation be sure there is enough slack in the tubing to move refrigerator out for cleaning under refrigerator.
Consult your local plumbing codes and install accordingly.
This filter must be protected from freezing, which can cause cracking of the filter and water leakage.
Because of the product’s limited service life and to prevent costly repairs or possible water damage, we strongly recommend that
the filter be replaced every 5 years. If the filter has been in use for longer than this period, it should be replaced immediately.
DANGER: EXPLOSIVE FIRE HAZARD. If your refrigerator is gas powered, double check to determine which lines are gas lines and
which are water lines.
DANGER
!

Helpful Hints
4
Step 1 Shut o water
Attach inbound water
line to filter
Step 2
Install filter and test for
leaks
Step 3
As Easy As...
• Locate the water line to your
refrigerator.
• Observe if it is a flexible hose or a rigid.
• Rigid pipes may require cutting.
• Determine if you have all appropriate
fasteners and adapters to fit your
plumbing.
• Consult your local plumbing codes
and install accordingly.
• Be sure to unplug appliance before
working on refrigerator.
• If refrigerator is gas powered double
check lines leading into the refrigerator.
Before You Start WARNING
!DANGER
For water lines larger than 1/4" OD or made
from galvanized pipe additional plumbing
hardware will be required. Please visit the
local hardware store for these fittings or call
customer service for assistance.
To Refrigerator
Supply line to Water Source
Flow
Quick Connect Fitting
Collet
Flexible hose
with nut
Adapter Fitting
For Flexible Hose with Nut
For Optional 1/4" Install

5
RF-103 installation instructions Version 1.0E
• Shut o the water supply to the
refrigerator and shut o the
icemaker if applicable.
• Have a container handy to catch any
water that leaks during installation.
• Turn o water supply to the
refrigerator and dispense the water
from the refrigerator door until water
flow stops.
• This releases pressure from the
pipes before installation.
Step 1 Shut O Water
WARNING
• Make sure the direction of water flow
through the filter is correct.
• Tighten each nut while using a second
wrench to hold the corresponding hex
fitting.
Supply line to
Water Source
bucket
DANGER
materials and tools needed
1 2 3
30’
tape measure utility knife
!
Step 2 Attach inbound
water line to filter
Step 2 continued on next page >>
materials and tools needed
To Refrigerator
bucket
safety glasses

6
• Install the appliance side of the water line into the fitting.
• Follow the same procedure as used for the supply side of the filter.
• Turn on the water supply.
• Check for leaks.
Note: If leaks continue, turn o the water supply and call Customer Service or your local plumber.
Supply line to
Refrigerator Source
• Turn on the water supply and flush
the filter into a container for ten
minutes.
• This flush will remove the air from
the filter and the small carbon
particles. During the flushing
process, the water will turn dark in
color. Continue flushing the new
filter until the water runs clear.
• Turn o the water supply.
• Warning: DO NOT screw system head
directly to refrigerator.
• Water supply to the refrigerator should
have a separate shut o valve installed
before the filter.
bucket
WARNING
Step 2
Attach inbound
water line to filter
Step 3
Install filter and test
for leaks
<< Step continued from previous page
materials and tools needed
WARNING

7
RF-103 installation instructions Version 1.0E
• Filter should be replaced every 5 years
(or sooner if pressure drop occurs).
• Do not use with water that is
microbiologically unsafe or of unknown
quality without adequate disinfection
before or after the system.
• Check filter every six months for leaks.
• Filter life and/or capacity is dependent upon
filter system, water quality and amount of
water filtered.
Filter Replacement
(every 5 years)
Performance
Data and
Maintenance
Brita®Filter RF-103
The Brita® Inline Icemaker filter used with this filter
system has a limited service life. Changes in taste,
odor, and/or flow of the water being filtered indicate
that the filter should be replaced.
Expected life of this filter is 5 years. Filter may need
to be changed sooner due to sediment in your water
source. For product information and assistance call
828-449-1040.
R
E
P
L
A
C
E
E
V
E
R
Y
F
I
V
E
Y
E
A
R
S
Need Help? 1-866-709-2086
Be sure to turn o the cold water supply until leak issue is resolved.
Installation Requirements
Operating Pressure: 30-100 PSI (207-690 kPa)
Temperature Range: 40-100°F (4.4-37.7° C)
Flow Rate: 0.5 GPM ( 1.9 lpm)
• Make sure the flow direction is
correct.
• Disconnect adapter fitting by
pushing the collet inward and
pulling the fitting out.
• Remove the adapter fitting from the
filter and discard. (See diagram).
• Cut the end of the tubing squarely.
Check the end of the tube to make
sure it is smooth with no ridges or
nicks. If needed cut the tubing again.
• Push tubing through the collet and
all the way into fitting. The length
of the tubing should extend 11/16”
into the fitting.
• Check for leaks.
Option
Optional Install for
¼” Plastic or
Copper tubing
do not bend or crimp
cut squarely on both ends
do not cut at an angle
wet ends of tubing before inserting

8

9
RF-103 installation instructions Version 1.0E
Instrucciones
de instalación
del RF-103
Refrigerador
En Linea Filtro
de nevera/
máquina de
hacer hielo
extendido
la vida
Paso 1
Paso 2
Paso 3
Tan fácil como...
Se conecta a la línea de
entrada de agua
vista frontal vista posterior
Sistema comprobado y certicado por NSF
Internacional contra NSF/ANSI 42 y 372 para la
reducción de los reclamos especicados en la
hoja de datos de rendimiento.
En Linea Filtro de nevera/ máquina de hacer hielo
extendido la vida Modelo RF-103

10
En Linea Filtro de
nevera/ máquina de
hacer hielo extendido
la vida
Principal:
Implementos necesarios para la instalación
Contenido del
paquete
artículos opcionales
bucket
cubo
Sistema de filtración universal My Brita® (reemplace el filtro cada 5 años)
866.709.2086
Información del producto y servicio www.protectplus.com www.protectplus.com
Video de instalación gratuito
Internet y móvil
Número de modelo del filtro Fecha de compra / Fecha de cambio Para recordatorios GRATIS de
cambio del filtro, ingrese a
www.protectplus.com
Implementos y materiales
necesarios
Filtro y acoplamiento adaptador
Fabricado por: Protect Plus, LLC 420 3rd Avenue NW, Hickory, NC 28601 USA
Cuchilla
multiuso
1 2 3
30’
Cinta para
medir
Gafas de
seguridad
segueta
cortador de tubos (para
instalación de tubos de cobre)
válvula de cierre
válvula de montura superior
con cierra
tuberia plástica de 1/4"
adaptador
adaptador
Acoplamiento
adaptador de 1/4"