Broyhill EDEN BL-BR-203-DR-4 User manual

•Bro hilr
INCE 1905


3

 
DRESSER

Need help? We are here for you!



  



Page 1 of 5
Determine you have adequate space for assembly.
Assembly by two adults is recommended.
Assembly on soft surfaces to prevent damage to product finish.
Keep children away during assembly. This item contains small parts which
can be swallowed by children.
Do not discard any of packaging until you have checked that you have all
parts and hardware.
Retain the assembly instructions for future reference.
The manufacturer will not accept responsibility for unauthorized repairs or
modifications to this product.
This product is for residential use only, not for commercial use.
A Phillips head screwdriver is necessary for assembly but is not included.
Warnings:
Wipe with a damp cloth. Use Furniture polish or lemon oil on the wood as
needed. Avoid prolonged exposure to moisture.
Do not scratch or chip the finish.
Do not put hot objects which are more than 80 degrees Fahrenheit directly on
the surface.
Check bolts/screws periodically and tighten if necessary.
To prolong the life of product we recommend storage in a dry area when not in use
or during austere weather conditions.
General best practices for assembly:
Should this product become damaged, and/or components are broken or missing,
DO NOT USE.
This product will burn if left in contact with flame source.
Maintenance:

PARTS LIST
Page 2 of 5
HARDWARE LIST
x 1 pc
Dresser body
Tipping Restrain x 1 set
x 4 pcs
Legs
x 1 pc
Support Leg
Spring Washer
x 4 pcs
Flat Washer x 4 pcs
Allen Key x 1 pc
Wood Dowel x 8 pcs
5mm
Allen Bolt x 4 pcs
Ø5/16''
Ø5/16''
Ø5/16'' x 4''
Ø8 x 30mm
A B C
1 2 3
4 5 6

Page 3 of 5
STEP 1
Assembled View:
Legs inside
Hardware needed
x4 x4 x4
x1 x8
1 2 3
4 5
A
B
53 2 1 4
A
Remove the carton containing the legs and hardware from
the drawer. With assistance, carefully place the Dresser
Body (A) onto it's back as shown. Insert the Wood Dowels
(5) into the holes at the corner of the Dresser Body (A).
Align the holes of Leg (B) with the dowels and slide into
place. Secure the Leg to the Dresser Body with Flat
Washer (3), Spring Washer (2) and Bolt (1) using Allen
Key (4). Fully tighten bolts. Repeat this step to attach
the remaining Legs.

Page 4 of 5
STEP 2
Assembled View:
A
C
A
Insert the Suppot Leg (C) into the hole in the center
of the Dresser bottom and rotate clockwise until
fully tightened. With Assistance, carefully return the
dresser back to the upright position.
Adjustable

Page 5 of 5
STEP 3
Wall
TIPPING
RESTRAIN HERE
WALL
NOT INCLUDED
NOT INCLUDED
WALL
NOT INCLUDED
NOT INCLUDED WALL
WALL
A
x1
PRINTED IN VIETNAM
ASSEMBLY IS COMPLETED
Hardware needed
6
6
This tipping restraint must be installed as directed before the Dresser can be used.
Place the dresser in the desired location. Locate a wall stud and mark the location of
the stud on the back of the dresser. Remove the dresser away from the wall.
Attach one of the brackets to the top rail of the dresser back in the marked location
using the supplied 5/8" screw. Place the screw through the smaller hole in the Bracket
and fully tighten using a Phillips Screwdriver (not provided).
Return the dresser to the desired location and mark the wall 2 inches below the
bracket on the dresser. Remove the dresser. Attach the remaining bracket to the wall
at the marked location using a Phillips Screwdriver (not provided). Warning: To work
properly, the screw inserted into the wall must be inserted into a wall stud or the
anchor can pull loose from the wall. Return the dresser back to the desired location
and attach the two brackets with the supplied restraint strap. Fully tighten the strap.