Broyhill LUXE ERGONOMIC HG-7513-1 Camel User manual

Read all instructions before starting.
Separate all parts before starting.
Clear a flat covered space to assemble.
If parts are missing, broken, damaged or worn, stop using the
product until all repairs are made.
Always keep children under close supervision while they are
using or around this product. Never leave children unattended.
This product is intended for domestic, indoor use only, not
intended for commercial use.
Do not stand or step on this chair.
Do not rock back and forth on this chair. Use for seating only one person at one time.
Do not use this product unless all bolts and screws are firmly secured.
Do not tighten screws before all screws are in the right place.
Do not exceed maximum weight capacity of 225lbs (102kg).
Some parts may contain sharp edges. Wear protective gloves if necessary.
MAINTENANCE:
WARNINGS:
GENERAL BEST PRACTICES FOR ASSEMBLY:
Wipe clean with a dry cloth for the upholstery and
frame. Do not use bleach, acid or other abrasive
cleaners. Check that all bolts and screws are
securely tightened at least every 3 months.

PARTS LIST
HARDWARE LIST
x1
Base
x5
Castor
x1
Gas Lift
x1
Seat Plate
x1 (Right)
Armrest
x1 (Left)
Armrest
x1
Seat Cushion
x1
Back Cushion
x8
Cap
x8
1/4x25mm Screw
x4
5/16x20mm Screw
x1
Allen Wrench
2
13

HELPFUL HINTS
1person
NOTE: To avoid damage, ensure
screws are hand tightened.
DO NOT USE POWER TOOLS TO
ASSEMBLE YOUR UNIT.

STEP 1
x5 x1
A B
x1
C
A
B
Insert the five castors (A) into the base (B) as shown in the diagram, make sure all castors are firmly inserted.

STEP 2
x1
C
B
C
Turn the base (B) right side up, insert gas lift (C) into the centre hole of base (B) as shown in the diagram.

STEP 3
x1 x1
DG
xx 4 4
1
x 1
3
1
1
3
3
G
D
Attach the seat plate (D) to the base of the seat cushion (G) using screws (1) and tighten with allen wrench (3).
Do not full tighten the screws until all screws are in place.

STEP 4
D
C
Carefully lower the seat plate (D) onto the gas lift (C) as shown in the diagram.

STEP 5
x1 (Right) x2
E2
x 1
3
G
E
3
2
Attach the right armrest (E) to the seat cushion (G) with screws (2) and tighten 70% with allen wrench (3). DO NOT fully tighten.

STEP 6
x1 (Left) x2
F2
x 1
3
F
G
3
2
Attach the left armrest (F) to the seat cushion (G) with screws (2) and tighten 70% with allen wrench (3). DO NOT fully tighten.

STEP 7
x1
H
x 2
2
x 1
3
3
H
E
H
3
2
Attach the back cushion (H) to the armrests (E) and (F), insert the screws (2) into each upper hole of armrests (E) and
(F) into the back cushion (H) as shown in the diagram. Tighten 70% with allen wrench (3). DO NOT fully tighten.

STEP 8
Lift the back cushion (H) up as shown in the diagram. Insert screws (2) into each bottom hole of armrests (E) and (F) into
the back cushion (H). Do not tighten screws before all parts are in the right place.
x 2
2
x 1
3
H
2

STEP 9
Tighten all screws using allen wrench (3). Place the caps (I) over the screws holes in the armrests (E) and (F) — four
caps per side. The assembly is complete, ensure all screws are tightened before use.
x8
I
I
Assembled View: