Broyhill CHICO GBO23-906SS-4 User manual

ASSEMBLY INSTRUCTIONS
ITEM# : GBO23-906SS-4
SKU# : 810580416
CHICO ALL WEATHER WICKER
UMBRELLA SIDE TABLE
Need help? We are here for you! 1-888-733-8169 Toll Free
Or email us at [e-mail],[e-mail]
[e-mail]

Read all instructions before starting
Clear a flat covered space to begin assembly
Always best to do it with a friend
Note that hardware required is provided for every step
Pay attention to orientation
Number of the hardware corresponds to its letter in the package
Helpful hints provided along the way
Retain these assembly instructions for future reference
WARNINGS:
To avoid hazards caused to the product or people around it, make sure to have weights applied to the base
of the table before you use umbrella with the table.
Fix the steel hoop plate underneath for better holding the weights for umbrella.
Use the correct bolts as indicated. All bolts should be hand tightened until the complete piece is assembled ( This will make the assembly
process much easier ). Once the piece is fully assembled, then go back and tighten all bolts with provided tool.
Regularly check hardware and tighten if necessary.
Do not discard of any of the packaging until you have checked that you have all of the parts and fittings required.
Keep children and pets away during assembly. This item contains small parts that can be swallowed by children.
Children should always be under direct adult supervision while using this product.
The table is not to be used for standing purposes, standing on or misuse of ottoman may result in damage or injury.
MAINTENANCE
Well recommend the use of furniture covers when not in use.
Inspect and tighten all of the bolts and fasteners on a regular basis to ensure the proper performance and safety of your outdoor furniture.
In order to prolong the life and beauty of your outdoor furniture, we recommend that it be stored in a dry and protected area during off
season periods.
GENERAL BEST PRACTISE FOR ASSEMBLY:
WARNINGS:
MAINTENANCE:
GENERAL BEST PRACTICE FOR ASSEMBLY:

PARTS LIST
Part No. Part Qty Image
Part
No.
Part Qty Image
1Table Top 1 6Short Bolt
(M6x12mm) 8
2Front Panel 2 7Long Bolt
(M6x30mm) 8
3Side Panel 2 8Washer 16
4Steel Hoop Plate 1 9Regulating Screw 1
5Umbrella Pole 1 10 Adjuster Knob 1
Tools
PARTS LIST:
PRODUCT FRAME MAP
8
1
3
2
10
OR

STEP 1
PART REQUIRED: 1，1PC 2 & 1PC 3
Keep the bolts loose.
STEP 2
PART REQUIRED: 1，2PC 2 & 1PC 3
Keep the bolts loose.
STEP 1
STEP 2
X2
X2
X2
X2
3
2
1
2
3
7
8
8
7
7
8
7
8
1
2

STEP 1
PART REQUIRED: 1，2PC 2 & 2PC 3
Keep the bolts loose.
STEP 2
PART REQUIRED: 4, 5 & 9
Keep the bolts loose.
STEP 3
STEP 4
X4
X4
X4
X4
3
2
3
9
5
4
7
8
8
6
7
8
6
8
2
THE STEEL HOOP PLATE CAN REMOVED FOR END TABLE USING ONLY.
LOAD THE WEIGHT ( SANDS BAG, STONE AND ETC. )
ONTO THE STEEL HOOP PLATE
WEIGHT MAX 100LBS

STEP 1
PART REQUIRED: 1, 2 , 3 & 4
Turn over the assembled table frame.
Keep the bolts loose.
STEP 2
PART REQUIRED: 10
Tighen all the bolts, tight adjuster knob (10) to table top (1) ,
Finished!
Warranty
One year limited warranty.
Proof of purchase (dated register receipt) is required for warranty claims.
It remains the customer's responsibility for freight and packing charges to and from the service center.
STEP 6
STEP 5
X4
X4
3
2
3
2
4
8
6
6
8
10
THE STEEL HOOP PLATE CAN REMOVED FOR END TABLE USING ONLY.
LOAD THE WEIGHT ( SANDS BAG, STONE AND ETC. )
ONTO THE STEEL HOOP PLATE
WEIGHT MAX 100LBS