Bticino 374004 Operating manual

Small Entrance Panel
374004
User and installation manual
www.bticino.com
RA00191AA-01/23-PC

Small Entrance Panel
User and installation manual

3
Contents
Small Entrance Panel
User and installation manual
General information 4
Warnings and recommendations 4
Warnings and consumer rights 4
Fundamental concepts 5
Naming of the devices 5
Community 5
Fire linkage 6
CCTV cameras 6
Front and rear view 6
Dimensional data and installation heights 9
Installation 10
Uninstall 14
Example diagrams 15
Ethernet connection 16
Fiber optic riser connection (case of higher bandwidth demand) 17
Available functions 18
Use of the device 19
Introduction 20
Functions 21
Call a IU 21
Answering machine 22
Call a GS 23
Access using badge or card 24
Settings 25
Device info 27
Factory setting 28
Send the configuration to the device 28
Restore factory 29
Login setting 30
Other setting 30
Audio parameters 31
Function status 31

Small Entrance Panel
User and installation manual
4
General information
Warnings and recommendations
It is important to read this manual carefully before proceeding with the installation.
The warranty becomes automatically void in case of negligence, improper use, tampering by
unauthorised personnel.
The Entrance Panel must not be exposed to water drops or splashes; it must be used only on IP
DES digital systems.
Read carefully before use and keep for future reference.
Touching the units with wet hands is forbidden.
Using liquid cleaners or aerosols is forbidden.
Blocking the ventilation openings is forbidden.
Modifying the devices is forbidden.
Removing protective parts from the devices is forbidden.
Exposing the unit to water drops or splashes is forbidden.
Installing the units near heat/cold sources is forbidden.
Installing the units near harmful gases and powders is forbidden.
Fastening the units on unsuitable surfaces is forbidden.
Danger of electrical shock.
Risk of devices falling because the surface on which they are installed collapses or
inappropriate installation.
Switch the power supply OFF before any work on the system.
Remote operation may cause damage to people or property.
Caution: Installation, configuration, starting-up and maintenance must be performed
exclusively by qualified personnel.
Check that the wall installation has been carried out correctly according to the installation
instructions.
Check that the unit installation complies with the standards in force.
Connect the power supply wires as indicated.
Use only the items indicated in the technical specifications for any system expansions.
Warnings and consumer rights

Small Entrance Panel
User and installation manual
54
Fundamental concepts
Naming of the devices
Community
In this manual, for easy reading, the abbreviated device name is used as in the list:
The term Community means the housing complex reproduced in the project design made using
the SW.
The structure in its maximum extension includes:
– IU: Indoor Unit
– EP: Entrance Panel
– GS: Guard Station
– SD: Server DES
– SEP: Small Entrance Panel
– AB: Address book
– SW: IP DES SYSTEM
RISER FLOOR APARTMENTAREA BUILDING
AREA 1
GS Area
EP Area
AREA 2
GS Area
EP Area
COMMUNITY
BUILDING 1
Floor 5
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 4
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 3
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 2
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 1
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
RISER 1 RISER 2
EP Building
BUILDING 1
Floor 5
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 4
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 3
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 2
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 1
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
RISER 1 RISER 2
EP Building
BUILDING 2
Floor 5
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 4
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 3
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 2
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 1
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
RISER 1 RISER 2
EP Building
BUILDING 2
Floor 5
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 4
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 3
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 2
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 1
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
RISER 1 RISER 2
EP Building

Small Entrance Panel
User and installation manual
6
CCTV cameras
CCTV cameras for passive video surveillance.
Fire linkage
It enables the door lock opening function in case of fire.
The Fire linkage function allows the automatic opening of SEP door locks in the event of a fire.
The use of this function requires a clean contact in the GND FIRE LINKAGE input clamp from the
fire fighting system.
It is necessary to enable the function in the Parameters section of the SD.
1. LED for the shooting field lighting
2. Camera
3. Light sensor
4. Badge reader for door lock opening
5. Microphone
6. Call key
7. Guard station call key
8. Loudspeaker
Front and rear view
8
321 1
5
6
4
7

Small Entrance Panel
User and installation manual
76
(*) This device does not support standard POE power supplies, but only POE power supplies
identified with item no. 375002.
Connect the cat5/5e/6 FTP or cat5/5e/6 UTP cable with ferrite supplied to the connector.
9. RJ45 Connector (*)
10. Connection clamp
11. Mounting bracket
12. Locking screw
13. Tamper switch
14. Reset pushbutton
SENSE
LOCK-
LOCK+
Fire Linkage
GND
+12V
OPEN
GND
RJ45
NC
COM
NO
DC24V
10
1213
9
11
14
10

Small Entrance Panel
User and installation manual
8
It is possible to display some wiring diagram examples in the functions section
Connection clamps
GND system common ground terminal
SENSE / GND door lock status signal input
LOCK- / LOCK+ electric door lock connection and control
(12V - 4A impulsive on 3 Ohm maximum)
OPEN / GND local door lock release pushbutton connection
FIRE Linkage / GND local door lock release pushbutton connection for firealarm system
+12V / GND access control devices power supply
NO / COM / NC interlocked dry contact for electric door lock connection
DC24V additional power supply clamps (not polarized)
GND
Sense
Open
Fire Linkage
SENSE
LOCK-
LOCK+
Fire Linkage
GND
+12V
OPEN
GND
RJ45
NC
COM
NO
DC24V

Small Entrance Panel
User and installation manual
98
Dimensional data and installation heights
*
160 – 165 cm
90 – 130 cm
53 °
50 cm
50 cm
80 °
(*) Recommended height, unless different regulations are specified.
193 mm
94 mm
60,6 mm
10 mm
20,6 mm
34,6 mm

Small Entrance Panel
User and installation manual
10
Installation
Attention: The wrong wiring of the Ethernet cable connecting the device to the Poe Switch 375002
could damage the device itself.
The RJ45 cable must be at least 200 mm long.
375008
3
2
1
84 mm
178
mm
59 mm
Caution: Do not install the device outside in direct sunlight.
Only install indoors, for example in stairwells or apartment landings.

Small Entrance Panel
User and installation manual
1110
2
1
3

Small Entrance Panel
User and installation manual
12
1
2 mm57 mm
1
2

Small Entrance Panel
User and installation manual
1312
(*) Adjust the tamper screw so that it presses the tamper switch of the device and activates the
anti-theft function in case of removal sending an alarm to the GS.
*
1
1
3
4

Small Entrance Panel
User and installation manual
14
Uninstall
1
2
3
45
6

Small Entrance Panel
User and installation manual
1514
Example diagrams
It is possible to use two different types of connection according to installation situation:
A - Diagram with power supply by BTicino PoE Switch B - Diagram with local power supply
Attention: this device does not support standard POE power supplies, but only POE power supplies identified with 375002. Connect the cat5/5e/6 FTP or cat5/5e/6
UTP cable with ferrite supplied to the connector.
Note: to connect the devices it is possible to use both types of wiring (diagram A or diagram B) or even mixed ones.
CABLES LEGEND LAN PoE BTicino LAN Ethernet Copper cables 2 x Copper cables
Attention: do not directly connect PoE ports to an unsuitable network interface, such as a device powered by a different voltage. Connect the UP LINK port to a
suitable port, never to a PoE port.
1 2
3 4 5 6
INPUT: 100–240 Vac 3.0A 50/60Hz
OUPUT:24 V 3.83A
L N
-V -V +V +V
1 2
374005
RJ45RJ45 RJ45 RJ45
373001
374000
RJ45
RJ45 RJ45
RJ45
RJ45
375002
373001
374001
374004
RJ45 RJ45 RJ45
RJ45
375001
PoE Switch
BTicino
100 – 240 Vac
PC client Server DES 230 V
Router
Modem router
DC24V
OUT 1 – 8
DC24V
DC24V
DC24V
DC24V
DC24V
DCO UTPUT:
2 4V 4.5A
100-240V~
50Hz/60Hz
ACINPUT:
373001 373001
374000
374001
374005
375005
RJ45RJ45 RJ45 RJ45 RJ45 RJ45
374004
RJ45RJ45RJ45
RJ45
RJ45
375001
100 – 240 Vac
24 Vdc 24 Vdc 24 Vdc 24 Vdc 24 Vdc
PC client 230 VServer DES
Modem router RouterRouter

Small Entrance Panel
User and installation manual
16
Ethernet connection
CABLES LEGEND LAN PoE Standard LAN PoE BTicino LAN Ethernet Copper cables 2 x Copper cables
1 2
3 4 5 6
INPUT: 100 – 240 Vac 3.0A 50/60Hz
OUPUT:24 V 3.83A
L N
-V -V +V +V
1 2
3 4 5 6
INPUT: 100 – 240 Vac 3.0A 50/60Hz
OUPUT:24 V 3.83A
L N
-V -V +V +V
OUT 1 – 8
DCO UTPUT:
24 V 4.5A
100-240V~
50Hz/60Hz
ACINPUT:
OUT 1 – 8 DC24V
DCO UTPUT:
24 V 4.5A
100-240V~
50Hz/60Hz
ACINPUT:
1 2
3 4 5 6
INPUT: 100 – 240 Vac 3.0A 50/60Hz
OUPUT:24 V 3.83A
L N
-V -V +V +V
DC24V
1 2
3 4 5 6
INPUT: 100 – 240 Vac 3.0A 50/60Hz
OUPUT:24 V 3.83A
L N
-V -V +V +V
1 2
3 4 5 6
INPUT: 100 – 240 Vac 3.0A 50/60Hz
OUPUT:24 V 3.83A
L N
-V -V +V +V
373001
373001 373001
373001
373001
373001
373001
373001
373001
373001
373001
373001
373001
373001
375002
375005
375005
374001
375000 374000
375000
RJ45
RJ45 RJ45
RJ45RJ45
RJ45 RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45 RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
375002
375002
375002
375002
374004
374005
RJ45 375001
FLOOR 2
FLOOR 3
FLOOR 1
Network switch
APARTMENT 1
APARTMENT 1
APARTMENT 1
APARTMENT 2
APARTMENT 2
APARTMENT 2
APARTMENT 3
APARTMENT 3
APARTMENT 3
APARTMENT 4
APARTMENT 4
APARTMENT 4
Network switch
Network switch
100 – 240 Vac
100 – 240 Vac
100 – 240 Vac
PoE Switch
BTicino
OnVif IP cameras
Standard PoE switch
100 – 240 Vac
PoE Switch
BTicino
PoE Switch
BTicino
PoE Switch
BTicino
Router Modem router
APARTMENT 5
PoE Switch
BTicino
100 – 240
Vac
PC client
Server DES 230 V
Note: to connect the devices it is possible to use both types of wiring (diagram A or diagram B) or even mixed ones.
Attention: do not directly connect PoE ports to an unsuitable network interface, such as a device powered by a different voltage. Connect the UP LINK port to a
suitable port, never to a PoE port.

Small Entrance Panel
User and installation manual
1716
Fiber optic riser connection (case of higher bandwidth demand)
Note: to connect the devices it is possible to use both types of wiring (diagram A or diagram B) or even mixed ones.
CABLES LEGEND LAN PoE Standard LAN PoE BTicino LAN Ethernet Optical fiber Copper cables 2 x Copper cables
Attention: do not directly connect PoE ports to an unsuitable network interface, such as a device powered by a different voltage. Connect the UP LINK port to a
suitable port, never to a PoE port.
1 2
3 4 5 6
INPUT: 100 – 240 Vac 3.0A 50/60Hz
OUPUT:24 V 3.83A
L N
-V -V +V +V
1 2
3 4 5 6
INPUT: 100 – 240 Vac 3.0A 50/60Hz
OUPUT:24 V 3.83A
L N
-V -V +V +V
OUT 1 – 8
DCO UTPUT:
24V 4.5 A
100-240V~
50Hz/60Hz
ACINPUT:
OUT 1 – 8 DC24V
DCO UTPUT:
24V 4.5 A
100-240V~
50Hz/60Hz
ACINPUT:
1 2
3 4 5 6
INPUT: 100 – 240 Vac 3.0A 50/60Hz
OUPUT:24 V 3.83A
L N
-V -V +V +V
1 2
3 4 5 6
INPUT: 100 – 240 Vac 3.0A 50/60Hz
OUPUT:24 V 3.83A
L N
-V -V +V +V
DC24V
1 2
3 4 5 6
INPUT: 100 – 240 Vac 3.0A 50/60Hz
OUPUT:24 V 3.83A
L N
-V -V +V +V
375005
375005
374001
375000
RJ45
RJ45
RJ45RJ45RJ45 RJ45 RJ45
RJ45
RJ45
RJ45
RJ45 RJ45
373001
373001
373001
373001
373001
373001
373001
373001
373001
373001
373001
373001
375002
375000 374000
RJ45 RJ45
RJ45
RJ45 RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
FO
FO
FO
FO
FO
RJ45
RJ45
RJ45
375002
375002
375002
373001 373001
RJ45
RJ45
RJ45
RJ45 RJ45
RJ45
375002
374004
374005
RJ45 375001
OnVif IP cameras
Standard PoE switch
Network switch
APARTMENT 1
APARTMENT 1
APARTMENT 1
APARTMENT 2
APARTMENT 2
APARTMENT 2
APARTMENT 3
APARTMENT 3
APARTMENT 3
APARTMENT 4
APARTMENT 4
APARTMENT 4
Network switch
Network switch
100 – 240 Vac
100 – 240 Vac
100 – 240 Vac
PoE Switch
BTicino
100 – 240 Vac
PoE Switch
BTicino
PoE Switch
BTicino
PoE Switch
BTicino
FLOOR 2
FLOOR 3
FLOOR 1
APARTMENT 5
PoE Switch
BTicino
100 – 240
Vac
PC client
Server DES 230 V
Router Modem router

Small Entrance Panel
User and installation manual
18
Note: to connect the devices it is possible to use both types of wiring (diagram A or diagram B) or even mixed ones.
Attention: do not directly connect PoE ports to an unsuitable network interface, such as a device powered by a different voltage. Connect the UP LINK port to a
suitable port, never to a PoE port.
Available functions
CABLES LEGEND LAN PoE BTicino LAN Ethernet Copper cables 2 x Copper cables
1 2
3 4 5 6
INPUT: 100–240 Vac 3.0A 50/60Hz
OUPUT:24 V 3.83A
L N
-V -V +V +V
SENSE
LOCK-
LOCK+
Fire Linkage
GND
+12V
OPEN
GND
RJ45
RJ45 RJ45
RJ45
375002
RJ45
375000
RJ45
RJ45
374004
RJ45
375001
RJ45 RJ45RJ45
Fire-fighting
system
Access
Control
Door
Status
Door lock
PoE Switch
BTicino
100 – 240
Vac
PC client Server DES 230 V
Network switch Router Modem router
Door open

Small Entrance Panel
User and installation manual
1918
Use of the device
After installing the SEP it is possible to:
– Call an IU
– Leave a message in the answering machine
– Call a GS
– Access using badge or card;
– Set the parameters

Small Entrance Panel
User and installation manual
20
Introduction
After the installation and connection of the device, it is necessary to configure it and create the
Community structure. For details see Server DES Software manual.
AREA
GS Area
EP Area
BUILDING 1
Floor 5
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 4
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 3
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 2
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 1
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
RISER 1 RISER 2
EP Building
BUILDING 2
Floor 5
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 4
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 3
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 2
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
Floor 1
Apartment 1 Apartment 2 Apartment 1 Apartment 2
DEVICE DEVICE DEVICE DEVICE
RISER 1 RISER 2
EP Building
Step
Step
Step
Step
Step
Community VLAN network creation
Community structure definition
Community structure creation
Device MAC address registration
01
02
03
04
05
06
07
08
Community customisation
09
10
11
Step
Step
Step
Step
Forwarding of the address book to the DES Server
Installation of the devices
Activation of the devices
System test
Step
Step
Registration of the Community on the installer’s Cloud
Saving of passwords