Bticino 342630 User manual

item 342630
BTicino s.p.a.
Via Messina, 38
20154 Milano - Italia
www.bticino.com
BTicino si riserva il diritto di variare, in qualsiasi momento, i contenuti illustrati nel presente stampato.
Instruction sheet
PART. T6101D - 05/05-01 PC

3
GB
CONTENTS
To change the menu display language:
• access the Programming mode described on page 11;
• perform the Language procedure described on page 14.
Sommario
INTRODUCTION _______________________________________________________________ 4
Warnings and tips ______________________________________________________________ 4
General description _____________________________________________________________ 4
Graphic display _________________________________________________________________ 5
Pushbuttons and their functions __________________________________________________ 5
Factory configuration ____________________________________________________________ 6
Reset factory configuration ______________________________________________________ 6
USE __________________________________________________________________________ 7
Looking for a resident whose name you know ______________________________________ 7
Looking for a resident whose code you know ______________________________________ 8
EXTRA EXTERNAL DEVICES ___________________________________________________ 9
Extra keypad module ___________________________________________________________ 9
I/R remote control ______________________________________________________________ 9
PROGRAMMING ______________________________________________________________ 10
Access to the programming _____________________________________________________ 10
Pushbuttons and their functions _________________________________________________ 10
Configuration menu ____________________________________________________________ 12
Secret code ___________________________________________________________________ 13
Language _____________________________________________________________________ 14
Address book format ___________________________________________________________ 15
Distribution board _____________________________________________________________ 16
Direct call _____________________________________________________________________ 17
Door code ____________________________________________________________________ 18
Contrast _____________________________________________________________________ 19
Recall _______________________________________________________________________ 20
Address book menu ___________________________________________________________ 21
TICALL SOFTWARE ___________________________________________________________ 28
CONFIGURATION _____________________________________________________________ 28
INSTALLATION _______________________________________________________________ 29

item 342630 4
WARNINGS AND TIPS
Read this manual carefully before installing the module.
INTRODUCTION
GENERAL DESCRIPTION
The digital speaker module with backlit graphic display can send the call to an internal unit.
You can scroll the resident names or codes on the display by means of the dedicated keys.
The module can save up to 1000 resident names and surnames associating them to the
unique configuration address* of the IU (Internal Unit) inside the system.
It can save 500 names if a message is associated with them. Whenever, for privacy reasons,
you decide to save only the resident codes, up to 5000 codes can be saved. Two different
names can be associated to the same MN address.
The manufacturer declines all responsibility for any damage due to incorrect use
and/or use which does not conform to the instructions in this manual.
(*) In this manual “Unique configuration address” will be abbreviated to MN.
TO CALL
A RESIDENT
PRESS
OR
LOUDSPEAKER
MICROPHONE
FUNCTION
PUSHBUTTON
IR RECEIVER
(programming via
remote control)
PC INTERFACE
CONNECTOR
GRAPHIC
DISPLAY

5
GB
INTRODUCTION
GRAPHIC DISPLAY
In the rest position the graphic distribution board display shows the screen to call a resident.
• Call the resident selected
• Scroll to a previous position (short press)
• Fast scroll (long 2-second press)
• Scroll to a later position (short press)
• Fast scroll (long 2-second press)
TO CALL
A RESIDENT
PRESS
OR
A
B
C
TO CALL
A RESIDENT
PRESS
OR
TO CALL
SWITCHBOARD
PRESS
BIANCHI
ROSSI
BIANCHI Mario
ROSSI Aldo
VERDI Marco
When the call to the distribution board and direct screens are enabled, they are shown
in succession and every ten seconds, alternating with the rest screen.
FAST SCROLL: The display shows several
residents at once.
PUSHBUTTONS AND THEIR FUNCTIONS
Use the three module pushbuttons to search in the address book, shown on the display, for
the resident name or code and make the call.

item 342630 6
INTRODUCTION
FACTORY CONFIGURATION
Secret code 1234
Language Italian
Address book format Alphanumeric without message
Distribution board 4000 Disabled
Direct call 0000 and 0001 Disabled
Door code 1234, 1235, 1236, 1237 and 1238
Contrast 50
Recall Disabled
RESET FACTORY CONFIGURATION
To reset the Factory configuration:
• Switch off the power supply to the device
• Put a jumper on the two lower interface pins
• Switch the device back on. The following mes-
sage appears on the display:
- RESET HARDWARE -
• Switch off the power supply to the device
• Remove the jumper
• Switch the device back on.
The Factory configuration is reset


7
GB
LOOKING FOR A RESIDENT WHOSE NAME YOU KNOW
To call a resident whose name you know:
TO CALL
A RESIDENT
PRESS
OR
BIANCHI
Mario
BIANCHI
Mario
TO CALL
TO CALL
CONNECTED
END
Bianchi
Mario
OUTGOING
CALL
BIANCHI
Mario
BIANCHI
Mario
• scroll the address book until the name required
appears on the display;
• press the pushbutton to make the call;
• Press a pushbutton to access the search;
When the resident answers the display signals that the
conversation is in progress.
• if there is no reply press the pushbutton to interrupt
the call;
When the resident puts down the handset of the internal
device, or after 60 seconds, the call is interrupted and
the display returns to the rest position.
USE
This type of search is only possible if ALPHANUMERIC has been set as Address
book Format.

item 342630 8
LOOKING FOR A RESIDENT WHOSE CODE YOU KNOW
To call a resident whose code you know:
This type of search is only possible if CODE has been set as Address book Format.
The codes must be programmed in the installation phase, associating an identification
code: B (block), F (floor) and I.U. (extension) with the resident.
USE
TO CALL
A RESIDENT
PRESS
OR
BLOCK B:1
OUTGOING
CALL
B:1 F:04
I.U.:00016
B:1 F:04
I.U.:00016
TO CONFIRM
TO CAL
CONNECTED
END
B:1
F:04
I.U.:00016
• Use the pushbuttons to select the Block, Floor
and Extension required and confirm each
choice.
• Press the pushbutton to make the call;
• Press a pushbutton to access the search;
When the resident answers the display signals that the
conversation is in progress.
• If there is no reply press the pushbutton to interrupt
the call;
When the resident puts down the handset of the internal
device, or after 60 seconds, the call is interrupted and
the display returns to the rest position.

9
GB
EXTRA KEYPAD MODULE
EXTRA EXTERNAL DEVICES
The infrared ray remote control (item 392123) can be used to program the resident address
book.
As well as the keys indicating letters and numbers, there are other keys for special program-
ming functions:
• NEXT MESS selection next/previous messages
• SHIFT modifies the function of the NEXT MESSAGE and all the keys with
double meaning
• RESET quits the editing phase losing each new setting
• MEMORY saves the new datum or the new selection
• BACK moves left by one position
• SPACE moves right by one position
• SHIFT + “ . “ enters a space (press SHIFT then “ . “)
TO CALL
A RESIDENT
PRESS
OR
1
9
4
7
2
5
8
0
3
6
A
B
C
D
The keypad module (item 342640) can:
• Call directly the resident whose name is known (if ALPHANUMERIC has been set as Ad-
dress book Format), keying in the MN address on the keypad.
• Call directly the resident whose code is known (if CODE has been configured as Address
book Format), keying in the code (Block, Floor, Extension) on the keypad.
• Open the door lock by pressing the pushbutton and typing a numerical code.
The keypad module is supplied with a multicable for the connection to the speaker module.




I/R REMOTE CONTROL
item 392123

item 342630 10
PROGRAMMING
ACCESS TO THE PROGRAMMING
Access to the Graphic Distribution board programming is protected by a Secret Code
(Factory 1234).
1234
-CONFIGURATION-
CONFIGURATION
ADDRESS BOOK
EXIT
TO CALL
A RESIDENT
PRESS
OR
TO CALL
A RESIDENT
PRESS
OR
0000
CONFIGURATION
CONFIGURATION
TO CONFIRM
TO CONFIRM
Once in Programming mode one can select:
• CONFIGURATION – to enter the device configuration menu.
• ADDRESS BOOK – to enter the address book configuration menu.
• QUIT – to quit the programming and go back to the initial page.
PUSHBUTTONS AND THEIR FUNCTIONS
• Moves the cursor right one figure (short press)
• Confirms and saves (long 2-second press)
• Scrolls by one position (short press)
• One unit increase (short press)
• Scrolls by one position (short press)
• One unit decrease (short press)
• Press pushbuttons C + A together to move the cursor one figure to the left
(typically first C and then A)
A
A
B
C
+
C