Bticino MINISFERA User manual

1
TECHNICAL SHEETS
Description
2 WIRE speaker module to be used in video or mixed audio/video systems.
Preset for 4 calls (expandable), it must be tted with surround plate (item 332721, item
332726) and keys (item 332712, item 332713, item 332714, item 332715), according to
personal installation requirements.
The device must be congured depending on the type of key used.
The Loudspeaker volume and the sensitivity level of the microphone may be adjusted
using the corresponding potentiometers.
The dedicated jumpers can be removed to enable the following functions: Staircase light
switching on with dedicated key, and exclusion of the conrmation of the call from the
entrance panel. If the IR LED allow night lighting of the eld of view.
The camera eld of view may be adjusted by +/-15 degrees both horizontally and
vertically.
The speaker module provides the possibility of opening an electrical door lock connected
directly to clamps S+ and S- (18V 4A impulsive, 250mA holding current 30Ω max). The
door lock can also be powered locally using a transformer, or the actuator item 346230/
item 346260.
Related items
332710 (ush mounted box)
332711 (surface-mounted box)
332712 (narrow key 1 module with name label)
332713 (wide key 2 modules with name label)
332714 (2 modules nameplate with label)
332715 (1 module false key - grey)
332721 (aluminium surround plate)
332726 (titanium surround plate)
Technical data
Power supply from SCS BUS: 18 - 27 Vdc
Stand by absorption: 40 mA
Max. operating absorption: 280 mA
Operating temperature: (-25) - (+70)°C
Dimensional data
Legend
1- Loudspeaker
2- Congurator socket
3- Call keys
4- Microphone
5- Loudspeaker volume adjustment
6- Microphone sensitivity adjustment
7- Staircase light switching on with dedicated key (remove the jumper to enable)
8- Entrance panel call conrmation exclusion. (remove the jumper to enable)
9- Terminal board for 2WIRE connections, door lock and opening of entrance door lock
10 -Camera eld of view adjustment screws
11 -IR LED for night lighting of the eld of view
342708
MINISFERA black and white
video pushbutton panel
BT00119-b-UK
160cm
21 mm
100 mm
245 mm
4
3
15°
15°
15°
15°
5
1
11
9
8
11
10
7
2
6

2
160 cm
item 332710
max. ø 5mm
item 332711
Conguration
The device must be congured (only phisically) as follows:
P - entrance panel number
The congurator in socket P of the speaker module assigns to this a recognition number
inside the system. The numbering of the entrance panels must always start from P=0.
The entrance panel congured with P=0 must be a common (or main) entrance panel.
N - call number
Assigns the correspondence between the entrance panel pushbuttons, and the audio
handsets.
In common entrance panels made using pushbutton modules, 1 must be inserted in N of
the speaker module. In secondary entrance panels, the number of the rst riser handset
must be inserted in N.
S - type of call signal
The conguration of S determines the call tone of SPRINT handsets.
One can thus dierentiate the calls from dierent entrance panels.
T - Door lock relay timing
0= No
congurator
4 sec.
1
1 sec. 6 sec. 8 sec. 10 sec.
2
2 sec.
3
3 sec. as
pushbutt.
4* 5 6 7
congurator number
Congurator 0 1 2 3
Type of bell 2-tone 2-tone 2-tone One-tone
1200Hz 1200Hz 1200Hz 1200Hz
600Hz 0 Hz 2400Hz
Table for SPRINT handset call signal
For the SWING, PIVOT, POLYX and AXOLUTE handsets, the S congurator associates the
entrance panel to the bell programmed in the same apartment. It is possible to chose
between 16 dierent bells. In one-family systems S=9 to congure the general call
(all the system handsets ring at the same time).
Inside the MINISFERA audio speaker module are JUMPERS that can be used for
performing the following functions:
• Jumper - EP call con rmation
To eliminate the entrance panel call conrmation sound remove the JUMPER .
• Jumper - staircase light switching on with call key
To switch on the staircase the light from the entrance panel using the last call key,
remove the JUMPER .
• Jumper – call pushbutton exclusion
Connect the jumper to exclude the call pushbutton.
NOTE: disable the pushbuttons based on the false poles, and the single, or the double
keys connected.
Example - To use the double key the upper level call must be disabled.
Double
keys
call pushbutton enabled call pushbutton disabled
Flush mounted installation
Installation
160 cm
item 332710
max. ø 5mm
item 332711
Wall mounted installation
BT00119-b-UK
* Operation as pushbutton for 10 sec. max, after which standby mode is activated.
To extend operation time over 10 seconds, use actuator item 346200 congured with
MOD=5.
342708