Bticino PIVOT Instruction manual

1
68,5 mm
210 mm
210 mm
6
5
4
1
2
8
3
7
OFF
ON
5
BUS
1
ET
21
NP
9
10
11
12
344122
14/10/2013BT00652-a-
Dimensional data
Description
2 WIRE PIVOT video handset for wall mounted, ush mounted, or table top installation.
TFT colour 4” at monitor. It has door lock release, staircase light, and entrance panel
activation keys.
The device oers the possibility of selecting among 16 already programmed bells for
oor call, main entrance panel, intercom call, and secondary entrance panel. The call
volume can be set on three levels: high, medium and disabled (this condition is signalled
by a ashing red LED).
It also has a call secrecy function. It is connected to the system using
the removable clamp supplied.
Wall mounting bracket supplied as standard.
Technical data
Power supply from SCS BUS: 18 – 27 Vdc
Stand by absorption: 5 mA
Max. operating absorption: 290 mA
Operating temperature: 5 - 40°C
Related items
346812 4 key small block for auxiliary functions - white
337122 table-top support - white
NOTE:for ush mounted installation refer to the specic accessories of the MULTIBOX
range.
PIVOT
colour video handset
Legend
1. 4”TFT colour monitor
2. Monitor colour, contrast, and brightness adjustment
3. Extensible cord capped on both ends with RJ connectors
4. Door lock key
5. Staircase light key
6. Entrance panel activation/cycling
7. Electronic call with volume adjustable on 3 levels: high, medium, disabled (the
excluded call is signalled by a ashing red LED)
8. 4-key block housing (optional)
9. Line termination ON/OFF micro-switch
10.Congurator socket
11.MASTER-SLAVE Jumper (remove to enable SLAVE)
12.Plug-in clamp for the connection of the 2 WIRE BUS, additional power supply,
and auxiliary oor call function, as well as extra bell.
2 WIRE Video Door Entry system
EN

2
SLAVE
NP
1
MASTER
NP
1
SLAVE
NP
1
MASTER
NP
1
41
1
16
2
RESET
1
16
2
RESET
1
16
2
RESET
1
16
2
RESET
OK
OK OK OK
2
4
3
1
2
4
3
1
2
4
3
1
2
4
3
1
41
1
16
2
RESET
1
16
2
RESET
1
16
2
RESET
1
16
2
RESET
OK
OK
OK OK
2
4
3
1
2
4
3
1
2
4
3
1
2
4
3
1
4
1
1
16
2
RESET
1
16
2
RESET
1
16
2
RESET
1
16
2
RESET
OK OK
OK
OK
2
4
3
1
2
4
3
1
2
4
3
1
2
4
3
1
4
1
1
16
2
RESET
1
16
2
RESET
1
16
2
RESET
1
16
2
RESET
OK OK OK
OK
2
4
3
1
2
4
3
1
2
4
3
1
2
4
3
1
344122
14/10/2013BT00652-a-
Conguration
N – handset number
The N congurator assigns each video handset an identication number within the
system. The handsets must be congured in progressive order. The handsets must be
congured in progressive order.Handsets with parallel connection (max 3 are allowed
inside apartments without 346850) must be congured using the same N congurator.
In parallel with the main video handset, additional handsets, video handsets and/or
bells may be installed.
P – entrance panel association
The P congurator identies the entrance panel associated, or the rst entrance panel to
activate before pressing the key and which door lock is activated when the key
is pressed while the video handset is idle. Connected
jumper
Disconnected
jumper
MASTER – SLAVE selection jumper
In multi-family systems with several video handsets (max. 3) connected in parallel
inside the same apartment (without using 346850), both the MASTER and the SLAVE
handsets must be set, by connecting or removing the selection jumper.
When a call is received, the MASTER video handset of the system rings and switches on,
while the video handsets congured as SLAVE only rings.
If the call is answered from a SLAVE unit, the MASTER unit switches o again, while the
monitor of the SLAVE unit the call has been answered from comes on.
When a pushbutton of SLAVE unit is pressed before answering, the MASTER
handset monitor switches o, while the monitor of SLAVE on which the pushbutton has
been pressed switches on, but without audio connection.
Bell selection from MAIN ENTRANCE
PANEL (S=0 - S=4)
FLOOR CALL bell selectionBell selection from SECONDARY
ENTRANCE PANEL (S=0 - S=5)
INTERCOM CALL bell selection
Programming of bells
PIVOT
colour video handset
EN