BWI Eagle AIR-EAGLE SR PLUS Manual

PRODUCT INFORMATION
BULLETIN
AIR-EAGLE®SR Plus
2.4GHz RF Transceiver
MODEL 36-40800-AC
DESCRIPTION
The AIR-EAGLE SRPLUS TRX is an R.F. transceiver capable of
transmitting and receiving commands from up to 600 feet away. This
model comes equipped with eight dry contact inputs and eight 5amp
relay outputs. When combined with another transceiver this allows the
user to transmit information out and receive a confirming signal back
that the operation was performed. This unit has eight user-selectable
network frequencies to allow multiple systems to operate
simultaneously in the same area without interference.
INSTALLATION
DISCONNECT AC Power from all equipment before installation.
1. Mount the AIR-EAGLE SR PLUS TRANSCEIVER in a convenient
location.
2. Install input and output wiring to terminal strip.
3. Install antenna onto connector located on the right side on the
enclosure.
4. Connect supplied power input cable to your external power source.
DIMENSIONS
TERMINAL STRIP WIRING
RELAY OUTPUTS
1
N/O Relay #1
10
N/O Relay #4
19
N/O Relay #7
2
C Relay #1
11
C Relay #4
20
C Relay #7
3
N/C Relay #1
12
N/C Relay #4
21
N/C Relay #7
4
N/O Relay #2
13
N/O Relay #5
22
N/O Relay #8
5
C Relay #2
14
C Relay #5
23
C Relay #8
6
N/C Relay #2
15
N/C Relay #5
24
N/C Relay #8
7
N/O Relay #3
16
N/O Relay #6
8
C Relay #3
17
C Relay #6
9
N/C Relay #3
18
N/C Relay #6
CONTACT INPUTS
1
Common Input 1
10
Input 5
2
Input 1
11
Common Input 6
3
Common Input 2
12
Input 6
4
Input 2
13
Common Input 7
5
Common Input 3
14
Input 7
6
Input 3
15
Common Input 8
7
Common Input 4
16
Input 8
8
Input 4
17
Not Used
9
Common Input 5
18
Not Used
AC INPUT
Terminal #1
100-250 VAC (N)
Terminal #2
100-250 VAC (H)

AIR-EAGLE®SR PLUS
2.4GHz RF Transceiver
MODEL 36-40800-AC
APPROVALS
United States (FCC)
MCQ-XBEE3
Canada (IC)
1846A-XBEE3
Europe (CE)
ETSI
GENERAL OPERATION
Contact closures on inputs 1 thru 8 in the control transceiver transmit
to activate relays #1 thru #8 in the remote transceiver. Inputs from the
remote equipment provide closures to remote transceiver that transmit
to energize relays 1 thru 8 in the control transceiver.
INPUT
ACTIVATED
ACTION
"1"
Transmits channel 1 command to remote unit
"2"
Transmits channel 2 command to remote unit
"3"
Transmits channel 3 command to remote unit
"4"
Transmits channel 4 command to remote unit
“5”
Transmits channel 5 command to remote unit
“6”
Transmits channel 6 command to remote unit
“7”
Transmits channel 7 command to remote unit
“8”
Transmits channel 8 command to remote unit
INPUT CODE
RECEIVED
ACTION
"1"
Relay #1 energizes, maintained momentary
"2"
Relay #2 energizes, maintained momentary
"3"
Relay #3 energizes, maintained momentary
"4"
Relay #4 energizes, maintained momentary
“5”
Relay #5 energizes, maintained momentary
“6”
Relay #6 energizes, maintained momentary
“7”
Relay #7 energizes, maintained momentary
“8”
Relay #8 energizes, maintained momentary
SPECIFICATIONS
Power Input
100-250 VAC, 5 W, 50/60 Hz
Fuse Protected
1 amp
Frequency
2.4GHz Spread Spectrum
Relay Contacts
SPDT 5 amp @ 120VAC or 30VDC per
channel
Transmitter Data
Eight Dry Contact Inputs
RF Output Power
60 mW
Transceiver Range
Up to 600 Feet
Note: Max range figures are estimates, based on free-air terrain with limited sources of
interference. Actual range will vary based on transmitting power, orientation of transmitter
and receiver, height of transmitting antenna, height of receiving antenna, weather
conditions, interference sources in the area, and terrain between receiver and transmitter,
including, but not limited to, indoor and outdoor structures such as walls, metal objects,
trees, buildings, hills, and mountains.
RF Networks
Eight Independent Frequencies
Enclosure
Hinged fiberglass with window / NEMA 3,
3R, 4, 12, 13
Operating Temp
-40oF to +185oF
RELAY & FREQUENCY SET-UP
This unit is shipped from the factory with the SEL1 switches in the open
positions. All eight relays will operate in a maintained momentary manor,
and unit is receiving commands on frequency one. If you wish to change
these defaultsettings, follow the instructions on the table below.
1) Remove power from unit
2) Remove top cover.
3) Select desired relay operation and/or network frequency using table
below.
4) Reattach cover and apply power.
5) Programming is now complete.
RELAY CONFIGURATION
SEL1
SWITCH
NUMBER
OPEN
CLOSED
SW1
Relays #1 thru #8 maintained
momentary (default)
Relays #1 thru #8
toggle/latch
Maintained Momentary –Relay mimics button orinput –when
depressed or closed, relay will be energized; when released, relay de-
energizes
Toggle Latch –Relay changes (and holds) its state each time the
corresponding button or input is depressed or closed momentarily
SW2-4
Not used on this model
FREQUENCY SET-UP
SEL1
Network
Freq#
SW5
SW6
SW7
(SW5-7)
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
8
CLOSED
CLOSED
CLOSED
ACCESSORIES
Standard Antenna (Included):
2.4GHz TNC “Rubber Duck” Antenna
49-1201
Mobile/Base Antennas –
Used to help achieve max range in both nonline of sight andline of
sight applications. - ContactBWI Eagle for recommendations
2.4GHz Thru-Hole Mount Mobile Antenna
49-2201
2.4GHz Magnet Mount Mobile Antenna
49-2202
2.4GHz Omni Directional Base Antenna
49-3201
2.4GHz Yagi Directional Base Antenna
49-3202
High Quality Coax Cables –
Used to connect external high gain antennas to control unit
Flex Coax Cable w/Connectors –Available in
5’,15’,25’,30’,40’,60’,80’,100’ Lengths
49-4000-XX
(XX = # of
Feet)
Bulkhead Extensions –
Used to provide an external antenna connection whenmounting
control unit inside another enclosure
TNC Male to TNCBulkhead CableAssembly -
Available in 2’, 4’, 7’ Lengths
49-5004-X-ISO
(X = # of Feet)

AIR-EAGLE®SR PLUS
2.4GHz RF Transceiver
MODEL 36-40800-AC
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly
used and installed, will be free from defects inmaterial and workmanship
for a period of 1 year after date of purchase. Said warranty to include the
repair or replacement of defective equipment. This warranty does not
cover damage due to external causes, including accident, problems with
electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair,improper installation, or improper
testing. This limited warranty, and any implied warranties that may exist
under state law, apply only to the original purchaser of the equipment, and
last only for as long as such purchaser continues to own the equipment.
This warranty replaces all other warranties, express or implied including,
but not limited to, the implied warranties ormerchantability and fitness for
a particular purpose. BWI Eagle makes no express warranties beyond
thosestatedhere. BWI disclaims without limitation, implied warranties of
merchantability and fitness for a particular purpose. Some jurisdictions do
not allowthe exclusion of implied warranties so this limitation may not
apply to you. To obtain warranty service, contact BWI Eagle for a return
material authorization. When returning equipment to BWI Eagle, the
customer assumes the risk of damage or loss during shipping and is
responsible fortheshipping costs incurred.