BWI Eagle AIR-EAGLE XLT Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®XLT
900 MHz RF Transmitter
MODEL 441-1400-DC
DESCRIPTION
The AIR-EAGLE XLT TX Is an R.F. transmitter capable of sending four
independent dry-contact input commands to an Air-Eagle XLT
Receiver located up to 2500 feet away (longer ranges can be achieved
with external high gain antennas) Any number of transmitters and
receivers can be combined to create a medium range radio frequency
system that operates hazardous or hard-to-reach electrical apparatus
from safe, convenient locations. Seven user-selectable frequencies
allow multiple systems to operate simultaneously in the same area
without interference.
APPROVALS
United States (FCC)
MCQ-XB900HP
Canada (IC)
1846A-XB900HP
INSTALLATION
1. Mount the AIR-EAGLE XLT TRANSMITTER in a convenient location.
2. Install wiring to contact input terminal strip (Note –the terminal block
header lifts off the base for easy wiring)
3. Make desired repeater mode and frequency selections using
instructions on page 2.
4. Attach supplied antenna to connector on right side of unit.
5. Connect DC power to the proper terminals in your control circuit.
TERMINAL STRIP WIRING
Wire as shown based on number of contact inputs
1
2
3
4
5
6
7
8
9
10
C Input 1
Input 1
C Input 2
Input 2
C Input 3
Input 3
C Input 4
Input 4
(-) 9-36VDC input
(+) 9-36VDC input
GENERAL OPERATION
A closure on any input transmits its channelcommand to activate the
corresponding relay in the remote receiver. The transmission continues as
long as the input is closed and ceases when the input opens.
Dimensions (with mounting plate) 6.3” L x 4.8” W x 2.3” H
CONTROLS & INDICATORS
TX LED
Illuminates green when power is applied.
Changes to red while any contact input is
closed and unit is transmitting.
Dry Contact Inputs
Transmits individual RF codes to the receiver
SEL2
Dip switch bank for digital address selection
SEL1
Dip switch bank for frequency & repeater
mode selection

AIR-EAGLE®XLT
900 MHz RF Transmitter
MODEL 441-1400-DC
DIGITAL ADDRESS, FREQUENCY &
REPEATER MODE SET-UP
The unit is shipped from the factory with all SEL1 and SEL2 switches in
the open positions. By default it is operating on DigitalAddress #1,
Frequency #1 and the command transmitted will not be repeated by the
receivers. If you wish to transmit on a different address and/or frequency,
and/orset the unit to transmit a repeating packet, follow the instructions
on the table below.
Note –only change digital address if using with a digitally
addressable receiver. Otherwise, the digital address must be kept at
the default of Digital Address “1”.
1) Remove power from unit and remove top cover.
2) Select desired digital address, network frequency and repeater
mode using tables below.
3) Reattach cover and apply power. Programming is now complete.
DIGITAL ADDRESS SET-UP
SEL2 (SW1 –4)
SEL2
(SW1-4)
Digital
Address
SW1
SW2
SW3
SW4
1 (default)
OPEN
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
OPEN
3
OPEN
CLOSED
OPEN
OPEN
4
CLOSED
CLOSED
OPEN
OPEN
5
OPEN
OPEN
CLOSED
OPEN
6
CLOSED
OPEN
CLOSED
OPEN
7
OPEN
CLOSED
CLOSED
OPEN
8
CLOSED
CLOSED
CLOSED
OPEN
9
OPEN
OPEN
OPEN
CLOSED
10
CLOSED
OPEN
OPEN
CLOSED
11
OPEN
CLOSED
OPEN
CLOSED
12
CLOSED
CLOSED
OPEN
CLOSED
13
OPEN
OPEN
CLOSED
CLOSED
14
CLOSED
OPEN
CLOSED
CLOSED
15
OPEN
CLOSED
CLOSED
CLOSED
16
CLOSED
CLOSED
CLOSED
CLOSED
SEL2 (SW5-7) –Leave in OPEN position!!
FREQUENCY SET-UP
SEL1 (SW1-3)
SEL1
(SW1-3)
Network
Frequency
SW1
SW2
SW3
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
REPEATER MODE
SEL1
SWITCH
NUMBER
OPEN
CLOSED
SW4
Repeater Mode OFF (default)
Repeater Mode ON
SPECIFICATIONS
DC Input
9-36VDC Input @ 10 W
Fuse Protected –1A Slo-Blo
Transmit Data
Four Dry Contact Inputs
Transmit Frequency
900MHz Spread Spectrum
RF Output Power
250 mW
Transmit Range
Approximately 2500 Feet w/standard
antenna
Transmitter Channels
7 Independent Network Frequencies
Enclosure
Polycarbonate, IP66 (NEMA 4)
Operating Temperature
-40oF to +185oF
REPLACEMENT PARTS & ACCESSORIES
PC Board (Main)
441-1402-DC
Standard Antenna (Included):
900MHz Portable Antenna (For distances up
to 2500 feet*)
49-1103
Optional Antennas and Accessories:
900MHz Omni Directional Antenna (For
distances up to 2 miles*)
49-3101
900MHz 13dB Yagi Antenna
Long Range Operation (For distances up to
4 miles*)
49-3102
Flex Coax Cable w/Connectors
49-4000-XX
(XX = # of Feet)
2 Ft. Bulkhead Assembly (Used when
mounting receive inside another enclosure)
49-5004-2-ISO
* = Line of Sight
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, ifproperly used and
installed, will be free from defects in material and workmanship for a period of 1 year
after date of purchase. Said warranty to include the repair or replacement of defective
equipment. This warranty does not cover damage due to external causes, including
accident, problems with electrical power, usage not in accordance with product
instructions, misuse, neglect, alteration, repair, improper installation, or improper
testing. This limited warranty, and any implied warranties that may exist under state
law, apply only to the original purchaser of the equipment, and last only for as long as
such purchaser continues to own the equipment. This warranty replaces all other
warranties, express or implied including, but not limited to, the implied warranties or
merchantability and fitness for a particular purpose. BWI Eagle makes no express
warranties beyond those stated here. BWI disclaims without limitation, implied
warranties of merchantability and fitness for a particular purpose. Some jurisdictions
do not allow the exclusion of implied warranties so this limitation may not apply to
you. To obtain warranty service, contact BWI Eagle for a return material
authorization. When returning equipment to BWI Eagle, the customer assumes the
risk of damage or loss during shipping and is responsible for the shipping costs
incurred.
DOCUMENT DATE: 02/05/2020 / PRODUCT REV. 4
105 Bonnie Drive
Butler, PA 16002
[phone]
Fax [phone]
www.bwieagle.com