BWI Eagle AIR-EAGLE SR PLUS 36-1800-120VAC Manual

PRODUCT INFORMATION
BULLETIN
238 Pillow Street
Butler, PA 16001
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®SR PLUS
2.4GHz 8 Input Transmitter
MODEL 36-1800-120VAC Rev.3
DESCRIPTION
The AIR-EAGLE SRPLUSRFTRANSMITTER IS an eight input unitdesigned
to transmit unique signals to an Air-Eagle Receiver(s) located up to 1200
feet away. The Air-Eagle SR PLUS TX is user-programmable for up to
128 digital addresses and eight network frequencies to allowmultiple
transceivers to operate simultaneously in the same area and utilizes
spread-spectrum technology and provides the utmost security and
reliabilityeven in the noisiest RF environments. A terminal strip has been
provided for interfacing with external drycontact inputs. This unit can
operate remote machinery such as pumps, gates, chutes etc.
INSTALLATION
DISCONNECT AC Power from all equipment before installation.
1. Mount the AIR-EAGLE SR PLUS TRANSMITTER in a convenient
location.
2. Install antenna. The unit has an antenna connector located on the
right side on the enclosure. Attach the supplied portable antenna or
coax for external antenna to this connector.
3. ConnectACpower and controltothe proper terminals in your control
circuit.
TERMINAL STRIP WIRING – BOTTOM PCB
1 N/O Input #1 7 N/O Input #4
2 C Input #1 8 C Input #4
3 N/O Input #2 9 120 VAC - (Neutral)
4 C Input #2 10 120 VAC - (Hot)
5 N/O Input #3
6 C Input #3
TERMINAL STRIP WIRING –TOP PCB
1 N/O Input #5 7 N/O Input #8
2 C Input #5 8 C Input #8
3 N/O Input #6 9 Not Used
4 C Input #6 10 Not Used
5 N/O Input #7
6 C Input #7
Dimensions (withmounting plate) 6.3” L x 4.8” W x 4.3” H
DIGITAL ADDRESS & FREQUENCY SET-UP
This transmitter is factory programmed to Frequency #1 and Digital
Address“0”. These settings can be changed by the user in any
combination but must matchthe corresponding receiver(s).
1) Remove top cover.
2) Selectdesired address and/or network frequency
3) Move SW4 on SEL2 to the “CLOSED” position. The TXLED will
illuminate RED (no data isbeing transmitted during this
programming)
4) Once LEDis illuminated, move SW4 on SEL2 back to the
“OPEN” position.The TX LEDwill illuminate GREEN.
5) Programming is now complete.Replace topcover.
Note – Selected address and frequency settings will be maintained, in
the internal flash memory, even if power is removed from unit. The
above procedure needs to be performed onlyif changing digital
address and/or network frequency)
SEL1 (ADDRESS) Seven dip switches for selectingdigitaladdress ofthis
transmitter (Maximum of 128 combinations)
Network
Address SW1 SW2 SW3
1 OPEN OPEN OPEN
2 CLOSED OPEN OPEN
3 OPEN CLOSED OPEN
4 CLOSED CLOSED OPEN
5 OPEN OPEN CLOSED
6 CLOSED OPEN CLOSED
7 OPEN CLOSED CLOSED
SEL 2 (SW 1-3):
(NETWORK
FREQUENCY)
8 CLOSED CLOSED CLOSED
Normal Operation Programming
SEL2 (SW4) OPEN CLOSED

AIR-EAGLE®SR PLUS
2.4 GHz 8 Input RF Transmitter
MODEL 36-1800-120VAC Rev.3
CONTROLS AND INDICATORS
BOTTOM
TOP
LED1 Illuminated green when power is applied.
Changes to red when transmitting data.
Inputs 1 thru 8 Eight normally open dry contact inputs
APPROVALS
United States (FCC) OUR-XBEEPRO
Canada (IC) 4214A-XBEEPRO
Europe (CE) ETSI
SPECIFICATIONS
AC Input 120 VAC, 16 W, 50/60 Hz
Fuse Protected 1 amp
RF Frequency 2.4 GHzSpread Spectrum
Input Channels 8 Dry Contact Inputs
RF Output Power 60 mW
Transmitter Range Approximately 1200 feet
Transmitter Frequencies 8 Independent Network Frequencies
Antenna Connection TNC Bulkhead
Enclosure Polycarbonate / NEMA 4, 4x, 12 + 13
Operating Temperature -40oF to +185oF
REPLACEMENT PARTS & ACCESSORIES
PC Board (Main) 36-1802-120VAC
Standard Antenna (Included):
2.4GHz TNC Portable Antenna (For
distances up to 1200 feet*) 49-1201
Optional Antennas and Accessories –
Used to increase range in both non line of sight and line of sight
applications. - Contact BWI Eagle for recommendations
2.4GHz Thru-Hole Mount Mobile Antenna 49-2201
2.4GHz Magnetic Mount Mobile Antenna 49-2202
2.4GHz Omni Directional Antenna 49-3201
2.4GHz 13dB Yagi Antenna 49-3202
Flex Coax Cable w/Connectors – Connects
external antenna(s) to base unit(s). 49-4000-XX (XX = # of Feet)
Inline Lightening Arrestor 49-5002
* = Line of Sight
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote ControlSystem, if properly used and
installed, will be free from defects in material and workmanship for a period of 1 year
after date of purchase. Said warranty to include the repair or replacement of defective
equipment. This warranty does not coverdamage due to externalcauses, including
accident, problems with electrical power, usage not in accordance withproduct
instructions, misuse, neglect, alteration, repair, improper installation, or improper
testing. This limited warranty, and anyimplied warranties that mayexist under state
law, apply only to the original purchaser of the equipment, and last only for as long as
such purchaser continues to own the equipment. This warranty replaces all other
warranties, express or implied including, but not limited to, the implied warranties or
merchantability and fitness for a particular purpose. BWI Eagle makes no express
warranties beyond thosestated here. BWIdisclaims without limitation, implied
warranties ofmerchantability and fitness for a particular purpose. Some jurisdictions
do not allow theexclusion of implied warranties so this limitation may not apply to
you. To obtain warranty service, contact BWI Eagle for a return material
authorization. Whenreturning equipmentto BWI Eagle, the customer assumes the
risk of damage or loss during shipping and is responsible for the shipping costs
incurred.
DOCUMENT DATE: 18-Jul-07
238 Pillow Street
Butler, PA 16001
[phone]
Fax [phone]
www.bwieagle.com