BWI Eagle AIR-EAGLE XLT Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®XLT
900 MHz RF Transmitter
MODEL 44-1200-BAT
DESCRIPTION
The AIR-EAGLE XLT MODEL 44-1200-BAT, is an R.F. transmitter
designed to send a single stop command to any Air-Eagle XLT
Receiver. The TX and RX combine to create a long range radio
frequency system that operates hazardous or hard-to-reach electrical
apparatus from safe, convenient locations of up to 2500 feet away (Up
to 4 mile range with optional antennas). This unit has 7 network
frequencies and 16 digital addresses to allow multiple systems to
operate simultaneously in the same area without interference.
APPROVALS
United States (FCC)
MCQ-XB900HP
Canada (IC)
1846A-XB900HP
INSTALLATION
1. Mount the AIR-EAGLE XLT TRANSMITTER in a convenient location
where the operator will have easy access to the stop button.
2. Install Ch. 2-4 wiringtocontact input terminal strip if desired.
3. Install the 2AA Lithium batteries that were provided.
4. Install antenna ontoconnector located on the right side on the
enclosure.
TERMINAL STRIP WIRING
Wire as shown based on number of contact inputs
1
2
3
4
5
6
7
8
9
10
E-Stop Button Pre- Wired to Input 1
C Input 2
Input 2
C Input 3
Input 3
C Input 4
Input 4
Not Used
Not Used
Dimensions (with mounting plate) 6.3” L x 4.8” W x 4.3” H
CONTROLS & INDICATORS
TX LED
Illuminates green when power is applied.
Changes to red while any contact input is
closed and unit is transmitting. When this
LED blinks briefly following a transmission,
the battery needs to be replaced.
Dry Contact Inputs
Transmits individual RF codes to the receiver
SEL2
Dip switch bank for digital address selection
SEL1
Dip switch bank for frequency selection

AIR-EAGLE®XLT
900 MHz RF Transmitter
MODEL 44-1200-BAT
DIGITAL ADDRESS & FREQUENCY SET-UP
This transmitter is factory programmed toDigital Address “1”and
Frequency “1”. These settings can be changed by the user in any
combination but must match the receiver that is set up to
communicate with this transmitter. Note –only change digital
address if using with a digitally addressable receiver. Otherwise, the
digital address must be kept at the default of Digital Address “1”.
1) Remove power from unit.
2) Remove top cover.
3) Select desired digital address and/or network frequency using table
below.
4) Reattach cover and apply power.
5) Programming is now complete.
DIGITAL ADDRESS SET-UP
SEL2 (SW1 –4)
SEL2
(SW1-4)
Digital
Address
SW1
SW2
SW3
SW4
1 (default)
OPEN
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
OPEN
3
OPEN
CLOSED
OPEN
OPEN
4
CLOSED
CLOSED
OPEN
OPEN
5
OPEN
OPEN
CLOSED
OPEN
6
CLOSED
OPEN
CLOSED
OPEN
7
OPEN
CLOSED
CLOSED
OPEN
8
CLOSED
CLOSED
CLOSED
OPEN
9
OPEN
OPEN
OPEN
CLOSED
10
CLOSED
OPEN
OPEN
CLOSED
11
OPEN
CLOSED
OPEN
CLOSED
12
CLOSED
CLOSED
OPEN
CLOSED
13
OPEN
OPEN
CLOSED
CLOSED
14
CLOSED
OPEN
CLOSED
CLOSED
15
OPEN
CLOSED
CLOSED
CLOSED
16
CLOSED
CLOSED
CLOSED
CLOSED
SEL2 (SW5-7) –Leave in OPEN position!!
FREQUENCY SET-UP
SEL1 (SW1-3)
SEL1
(SW1-3)
Network
Frequency
SW1
SW2
SW3
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
SEL1 (SW4) –Not used on this model
SPECIFICATIONS
Power Requirements
3.0 VDC
Battery Type
(2) 1.5V lithium or alkaline each,size
AA, to equal 3.0VDC nominal.
Battery Life
(Active Usage)
Approximately 3 months
Battery Life (Idle)
Up to 1 Year
Transmit Data
Four Dry Contact Inputs
Transmit Frequency
900MHz Spread Spectrum
RF Output Power
250 mW
Transmit Range
Approximately 2500 Feet w/standard
antenna
Transmitter Channels
7 Independent Network Frequencies
Enclosure
Polycarbonate, IP66 (NEMA 4)
Operating Temperature
-40oF to +185oF
REPLACEMENT PARTS & ACCESSORIES
PC Board (Main)
44-1202-BAT
Standard Antenna (Included):
900MHz Portable Antenna (For distances up
to 2500 feet*)
49-1103
Optional Antennas and Accessories:
900MHz Omni Directional Antenna (For
distances up to 2 miles*)
49-3101
900MHz 13dB Yagi Antenna
Long Range Operation (For distances up to
4 miles*)
49-3102
Flex Coax Cable w/Connectors
49-4000-XX
(XX = # of Feet)
* = Line of Sight
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, ifproperly used and
installed, will be free from defects in material and workmanship for a period of 1 year
after date of purchase. Said warranty to include the repair or replacement of defective
equipment. This warranty does not cover damage due to external causes, including
accident, problems with electrical power, usage not in accordance with product
instructions, misuse, neglect, alteration, repair, improper installation, or improper
testing. This limited warranty, and any implied warranties that may exist under state
law, apply only to the original purchaser of the equipment, and last only for as long as
such purchasercontinues to own the equipment. This warranty replaces all other
warranties, express or implied including, but not limited to, the implied warranties or
merchantability and fitness for a particular purpose. BWI Eagle makes no express
warranties beyond those stated here. BWI disclaims without limitation, implied
warranties of merchantability and fitness for a particular purpose. Somejurisdictions
do not allow the exclusion of implied warranties so this limitation may not apply to
you. To obtain warranty service, contact BWI Eagle for a return material
authorization. When returning equipment to BWI Eagle, the customer assumes the
risk of damage or loss during shipping and is responsible for the shipping costs
incurred.
DOCUMENT DATE: 04/24/2019 / PRODUCT REV. 4
105 Bonnie Drive
Butler, PA 16002
[phone]
Fax [phone]
www.bwieagle.com