BWI Eagle AIR-EAGLE XLT Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®XLT
900 MHz RF Transmitter
MODEL 44-1400-120I-120VAC
DESCRIPTION
The AIR-EAGLE XLT TXIs an R.F. transmitter capable of sending four
120VAC input commands to an Air-Eagle XLT Receiver located up to
2500 feet away (longer ranges can be achieved with external high gain
antennas) Any number of transmitters and receivers can be combined
to create a medium range radio frequency system that operates
hazardous or hard-to-reach electrical apparatus from safe, convenient
locations. Seven user-selectable frequencies allow multiple systems to
operate simultaneously in the same area without interference.
APPROVALS
United States (FCC)
MCQ-XB900HP
Canada (IC)
1846A-XB900HP
INSTALLATION
1. Mount the AIR-EAGLE XLT TRANSMITTER in a convenient location.
2. Install wiring to input terminalstrip (Note –the terminal block header
lifts up off the base for easy wiring)
3. Attach supplied antenna to connector on right side of unit.
4. Plug supplied AC wall plug adapter into AC outlet.
TERMINAL STRIP WIRING
Wire as shown based on number of contact inputs
1
2
3
4
5
6
7
8
9
10
Input 1 –120VAC (Neutral)
Input 1 –120VAC (Hot)
Input 2 –120VAC (Neutral)
Input 2 –120VAC (Hot)
Input 3 –120VAC (Neutral)
Input 3 –120VAC (Hot)
Input 4 –120VAC (Neutral)
Input 4 –120VAC (Hot)
(-) 12VDC input from included AC wall adapter
(+) 12VDC input from included AC wall adapter
GENERAL OPERATION
Transmission occurs when 120VAC is applied to the input. Transmission
continues while 120VAC is present and ceases when 120VAC is
removed.
Dimensions (with mounting plate) 6.3” L x 4.8” W x 2.3” H
CONTROLS & INDICATORS
TX LED
Illuminates green when power is applied.
Changes to red while voltage is applied to
any input and unit is transmitting.
Voltage Inputs
Transmits individual RF codes to the
receiver
SEL2
Dip switch bank for digital address selection
SEL1
Dip switch bank for frequency selection

AIR-EAGLE®XLT
900 MHz RF Transmitter
MODEL 44-1400-120I-120VAC
DIGITAL ADDRESS & FREQUENCY SET-UP
This transmitter is factory programmed to Digital Address “1”and
Frequency “1”. These settings can be changed by the user in any
combination but must match the receiver that is set up to
communicate with this transmitter. Note –only change digital
address if using with a digitally addressable receiver. Otherwise, the
digital address must be kept at the default of Digital Address “1”.
1) Remove power from unit.
2) Remove top cover.
3) Select desired digital address and/or network frequency using table
below.
4) Reattach cover and apply power.
5) Programming is now complete.
DIGITAL ADDRESS SET-UP
SEL2 (SW1 –4)
SEL2
(SW1-4)
Digital
Address
SW1
SW2
SW3
SW4
1 (default)
OPEN
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
OPEN
3
OPEN
CLOSED
OPEN
OPEN
4
CLOSED
CLOSED
OPEN
OPEN
5
OPEN
OPEN
CLOSED
OPEN
6
CLOSED
OPEN
CLOSED
OPEN
7
OPEN
CLOSED
CLOSED
OPEN
8
CLOSED
CLOSED
CLOSED
OPEN
9
OPEN
OPEN
OPEN
CLOSED
10
CLOSED
OPEN
OPEN
CLOSED
11
OPEN
CLOSED
OPEN
CLOSED
12
CLOSED
CLOSED
OPEN
CLOSED
13
OPEN
OPEN
CLOSED
CLOSED
14
CLOSED
OPEN
CLOSED
CLOSED
15
OPEN
CLOSED
CLOSED
CLOSED
16
CLOSED
CLOSED
CLOSED
CLOSED
SEL2 (SW5-7) –Leave in OPEN position!!
FREQUENCY SET-UP
SEL1 (SW1-3)
SEL1
(SW1-3)
Network
Frequency
SW1
SW2
SW3
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
SEL1 (SW4) –Not used on this model
SPECIFICATIONS
AC Input
100-240 VAC, 16W, 50/60 Hz from
supplied wall adapter
Transmit Data
Four 120VAC Inputs
Transmit Frequency
900MHz Spread Spectrum
RF Output Power
250 mW
Transmit Range
Approximately 2500 Feet w/standard
antenna
Transmitter Channels
7 Independent Network Frequencies
Enclosure
Polycarbonate, IP66 (NEMA 4)
Operating Temperature
-40oF to +185oF
REPLACEMENT PARTS & ACCESSORIES
PC Board (Main)
44-1402-120I-DC
Standard Antenna (Included):
900MHz Portable Antenna (For distances up
to 2500 feet*)
49-1103
Optional Antennas and Accessories:
900MHz Omni Directional Antenna (For
distances up to 2 miles*)
49-3101
900MHz 13dB Yagi Antenna
Long Range Operation (For distances up to
4 miles*)
49-3102
Flex Coax Cable w/Connectors
49-4000-XX
(XX = # of Feet)
* = Line of Sight
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly used and
installed, will be free from defects in material and workmanship for a period of 1 year
afterdate of purchase. Said warranty to include the repair or replacement of defective
equipment. This warranty does not cover damage due to external causes, including
accident, problems with electrical power, usage not in accordance with product
instructions, misuse, neglect, alteration, repair, improper installation, or improper
testing. This limited warranty, and any implied warranties that may exist under state
law, applyonly to the original purchaser of the equipment, and last onlyfor as long as
such purchaser continues to own the equipment. This warrantyreplaces all other
warranties, express or implied including, but not limited to, the implied warranties or
merchantability and fitness for a particular purpose. BWI Eagle makes no express
warranties beyond those stated here. BWI disclaims without limitation, implied
warranties of merchantability and fitness for a particular purpose. Some jurisdictions
do not allow the exclusion of implied warranties so this limitation maynot apply to
you. To obtain warranty service, contact BWI Eagle for a return material
authorization.When returning equipment to BWI Eagle, the customer assumes the
risk of damage or loss during shipping and is responsible for the shipping costs
incurred.
DOCUMENT DATE: 03/19/2019 / PRODUCT REV. 4
105 Bonnie Drive
Butler, PA 16002
[phone]
Fax [phone]
www.bwieagle.com