BWI Eagle AIR-EAGLE SR PLUS Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®SR PLUS
2.4 GHz RF Transmitter
MODEL 36-1200-BAT
DESCRIPTION
The AIR-EAGLE SRPLUS, MODEL 36-1200-BAT is an R.F. transmitter
designed to send a single stop command to any Air-Eagle SR Receiver
from up to 600 feet away. Any number of transmitters and receivers
can be combined to create a remote control system. This unit has eight
network frequencies and sixteen digital addresses to allow multiple
systems to operate simultaneously in the same area without
interference.
APPROVALS
United States (FCC)
OUR-XBEEPRO
Canada (IC)
4214A-XBEEPRO
Europe (CE)
ETSI
INSTALLATION
1. Mount the AIR-EAGLE SR PLUS TRANSMITTER in a convenient
location where the operator will have easy access to thestop button.
2. Install Ch. 2-4 wiringtocontact input terminalstrip if desired.
3. Install the two AA lithium batteries that were provided.
4. Install antenna onto connector on the right side of the enclosure.
TERMINAL STRIP WIRING
Wire as shown based on number of contact inputs
1
2
3
4
5
6
7
8
9
10
E-Stop Button Pre- Wired to Input 1
C Input 2
Input 2
C Input 3
Input 3
C Input 4
Input 4
Not Used
Not Used
Dimensions (with mounting plate) 6.3” L x 4.8” W x 4.3” H
CONTROLS & INDICATORS
TX LED
Illuminates red while booting up, then
extinguishes.Illuminates red while any contact
input is closed and unit is transmitting.When
this LED blinks briefly following a
transmission, the battery needs to be
replaced.
Dry Contact Inputs
Transmits individual RF codes to the receiver
SEL2
Dip switch bank for digital address selection
SEL1
Dip switch bank for frequency selection

AIR-EAGLE®SR PLUS
2.4 GHz RF Transmitter
MODEL 36-1200-BAT
DIGITAL ADDRESS & FREQUENCY SET-UP
This transmitter is factory programmed to Digital Address “1”and
Frequency “1”. These settings can be changed by the user in any
combination but must match the receiver that is set up to
communicate with this transmitter. Note –only change digital
address if using with a digitallyaddressable receiver. Otherwise, the
digital address must be kept at the default of Digital Address “1”.
1) Remove power from unit.
2) Remove top cover.
3) Select desired digital address and/or network frequency using table
below.
4) Reattach cover and apply power.
5) Programming is now complete.
DIGITAL ADDRESS SET-UP
SEL2 (SW1 –4)
SEL2
(SW1-4)
Digital
Address
SW1
SW2
SW3
SW4
1 (default)
OPEN
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
OPEN
3
OPEN
CLOSED
OPEN
OPEN
4
CLOSED
CLOSED
OPEN
OPEN
5
OPEN
OPEN
CLOSED
OPEN
6
CLOSED
OPEN
CLOSED
OPEN
7
OPEN
CLOSED
CLOSED
OPEN
8
CLOSED
CLOSED
CLOSED
OPEN
9
OPEN
OPEN
OPEN
CLOSED
10
CLOSED
OPEN
OPEN
CLOSED
11
OPEN
CLOSED
OPEN
CLOSED
12
CLOSED
CLOSED
OPEN
CLOSED
13
OPEN
OPEN
CLOSED
CLOSED
14
CLOSED
OPEN
CLOSED
CLOSED
15
OPEN
CLOSED
CLOSED
CLOSED
16
CLOSED
CLOSED
CLOSED
CLOSED
SEL2 (SW5-7) –Leave in OPEN position!!
FREQUENCY SET-UP
SEL1 (SW1-3)
SEL1
(SW1-3)
Network
Frequency
SW1
SW2
SW3
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
8
CLOSED
CLOSED
CLOSED
SEL1 (SW4) –Not used on this model
SPECIFICATIONS
Power Requirements
3.0 VDC
Battery Type
(2) 1.5V lithium or alkaline each, size
AA, to equal 3.0VDC nominal.
Battery Life
(Active Usage)
Approximately 3 months
Battery Life (Idle)
Up to 1 Year
Enclosure
Polycarbonate IP66
Transmit Frequency
2.4GHz Spread Spectrum
Transmitter Coding
128 Digital Addresses
(Available only when communicating with model
38-8000)
Transmitter Channels
8 Independent Network Frequencies
Antenna Connection
TNC Female
RF Output Power
60 mW
Transmit Range
Approximately 600 Feet
Operating Temperature
-40oF to +185oF
REPLACEMENT PARTS & ACCESSORIES
PC Board (Main)
36-1202-BAT
Standard Antenna (Included):
2.4GHz TNC Portable Antenna (For
distances up to 600 feet*)
49-1201
Optional Antennas and Accessories –
Used to increase range in both non line of sight and line of sight
applications. - Contact BWI Eagle for recommendations
2.4GHz Thru-Hole Mount Mobile Antenna
49-2201
2.4GHz Magnetic Mount Mobile Antenna
49-2202
2.4GHz Omni Directional Antenna
49-3201
2.4GHz 13dB Yagi Antenna
49-3202
Flex Coax Cable w/Connectors –Connects
external antenna(s) to base unit(s).
49-4000-XX
(XX = # of Feet)
* = Line of Sight
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly
used and installed, will be free from defects in material and workmanship
for a period of 1 year after date of purchase. Said warranty to include the
repair or replacement of defective equipment. This warranty does not
cover damage due to external causes, including accident, problems with
electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair,improperinstallation, or improper
testing. This limited warranty, and any implied warranties that may exist
under state law, apply onlyto the original purchaser of the equipment, and
last only for as long as such purchasercontinues to own the equipment.
This warranty replaces all other warranties, express or implied including,
but not limited to, the implied warranties or merchantability and fitness for
a particular purpose. BWI Eaglemakes no express warranties beyond
those stated here. BWI disclaims without limitation, implied warranties of
merchantability and fitnessfor a particular purpose. Some jurisdictions do
not allowthe exclusion of implied warranties so this limitation maynot
apply to you. To obtain warranty service, contact BWI Eagle for a return
material authorization. When returning equipment to BWI Eagle, the
customer assumes the risk of damage or loss during shipping and is
responsible for the shipping costs incurred.
DOCUMENT DATE: 04/24/2019 / PRODUCT REV. 5