CAME Z Series User manual

-1-
Documentazione
Tecnica
S13
rev. 2.1
02/2001
© CAME
CANCELLI
AUTOMATICI
319S13
SCHEDA COMANDO
CONTROL BOARD
CARTE DE COMMANDE
STEUERPLATINE
TARJETA DE MANDO
SERIE Z | Z SERIES / SÉRIE Z | BAUREIHE Z | SERIE Z
ZA3
CANCELLI AUTOMATICI
Descrizione scheda comando
La scheda elettrica ZA3 è adatta al
comando di automazioni per cancelli a
battente della serie ATI, FERNI e
FROG, alimentati a 230V con potenza
fino a 600W, frequenza 50÷60 Hz.
Progettata e costruita interamente
dalla CAME S.p.A., risponde alle
vigenti norme UNI 8612. La scheda va
inserita e fissata nel contenitore in
ABS (S4339 o S4340) con grado di
protezione IP54, dotato di
presa per il riciclo d’aria e completo di
trasformatore.
La scheda va alimentata con tensione
di 230V (a.c.) sui morsetti L1-L2 e
protetta in ingresso con due fusibili di
linea da 5A. I dispositivi di comando
sono a bassa tensione e protetti con
fusibile da 3.15A.
La potenza complessiva degli accesso-
ri (24V) non deve superare i 20W.
CARATTERISTICHE GENERALI
ITALIANO
QUAD RO COMAN DO
FUSIBILI
LINEA 5A
ZA3
CH1
AF
FUSIBILE
CENTRALINA
2A
T.L. T.C.A. TR2M. 2134567
8910
O
N
CH2

-4-
GENERAL CHARACTERISTICS
ENGLISH
Description of control board
The ZA3 electric board is suitable for
controlling the automation of ATI,
FERNI and FROG series 230V swing
gates with up to 600W power and 50-
60Hz frequency.
Wholly designed and built by CAME
S.p.A., it meets UNI 8612 regulations
in force. The board is inserted and
fixed to the ABS case (S4339 o
S4340), which has an IP54 protection
level, with air recycling inlet and
transformer.
The board requires 230V (a.c.) at
terminal blocks L1-L2 and the inlet is
protected with two 5A fuses. A 3.15A
fuse protects the low voltage command
devices.
The accessories’total wattage (24V)
must not exceed 20W.
Safety
Photocells can be connected to
obtain:
- Re-opening during closure (2-C1), if
the photocells identify an obstacle
while the gate is closing, they will
reverse the direction of movement until
the gate is completely open;
- Re-closing during opening (2-CX, dip
8OFF-10OFF), if the photocells identify
an obstacle while the gate is opening,
they will reverse the direction of
movement until the gate is completely
closed;
- Partial stop, shutdown of moving
gate, with activation of an automatic
closing cycle (2-CX);
- Total stop (1-2), shutdown of gate
movement without automatic closing; a
pushbutton or radio remote control
must be actuated to resume
movement).
NB: If an NC safety contact (2-C1, 2-
CX, 1-2) is opened, the LED will flash
to indicate this fact.
Accessories which can be
connected to this unit
- “Gate open”signal ligh t (10-5);
- Cycle lamp. The lamp which lights the
manoeuvring zone: it remains lit from
the moment the doors begin to open
until they are completely closed
(including the time required for the
automatic closure). In case automatic
closure is not enabled, the lamp
remains lit only during movement (E-
E3);
- Electric lock (11-S);

-5-
Other functions available
- Automatic closing. The automatic
closing timer is automatically activated
at the end of the opening cycle. The
preset, adjustable automatic closing
time is automatically interrupted by the
activation of any safety system, and is
deactivated after a STOP command or
in case of power failure;
- Obstacle presence detection: When
the motor is stopped (gate is closed,
open or half-open after an emergency
stop command), the transmitter and
the control pushbutton will be
deactivated if an obstacle is detected
by one of the safety devices (for
example, the photocells);
- Hammer movement. At every opening
command, the wings press the closing
stop-ledge for a second, thus facilitat-
ing the release operation of the electric
lock connected to terminals 11-S.
It is only active if the wings are closed
and at the end of the work time or at
the 1st manoeuvre after the system has
been powered;
- Enabling functions of partial stop or
re-closure during opening, normally-
closed contact (2-CX), select one of
the two functions by setting Dip (see
page 14);
- "Operator present" function: Gate
operates only when the pushbutton is
held down (the radio remote control
system is deactivated);
- Partial opening , second motor door
opening, adjusted with TR2M trimmer;
it is activated by collecting to the
terminals 2-3P;
- Pre-flashing for 5 seconds, while the
door is opening and closing;
- Type of command:
-open-stop-close-stop for pushbutton
and radio transmitter;
- open-close-reverse for pushbutton
and radio transmitter;
-open only for radio transmitter.
Adjustments
- Automatic closure time;
- Partial opening time and delay in
closing of the M2 motor;
- Operating time.
Important! Disconnect the unit
from the main power lines before
carrying out any operation inside the
unit.

-12-
COMPONENTI PRINCIPALI
1 Morsettiere di collegamento
2 Fusibili di linea 5A
3 Fusibile centralina 3,15A
4 LED di segnalazione tensione presente 24V
5 Pulsanti memorizzazione codice radio
6 Trimmer di regolazione tempo lavoro
7 Trimmer di regolazione tempo in chiusura automatica
8 Trimmer di regolazione ritardo in chiusura 2° motore e apertura parziale
9 Selettore funzioni a 10 dip (vedi pagina 14)
10 Innesto scheda radiofrequenza (vedi tabella)
11 LED segnalazione
12 Limitatore di coppia (vedi pagina 21)
ITALIANO
1 2 3 4
L2T L1T
024 12
QUA DRO COMANDO
FUSIBILI
LINEA 5A
ZA3
CH1
AF
FUSIBILE
CENTRALINA
2A
T.L. T.C.A. TR2M.
2
1 3 45 67 8910O
N
CH2
1
2
3
4 5 6 7 8 9
10
11
12
Nero
Black
Noir
Schwarz
Negro
Rosso
Red
Rouge
Rot
Rojo
SCHEDA BASE - MOTHERBOARD - CARTE BASE - GRUNDPLATINE - TARJETA BASE
Nota: serie FROG, collega-
re i fili neri che fuoriescono
dalla scheda sui connettori
del condensatore del 1°
motore e i fili rossi sul con-
densatore del 2° motore.
NB: FROG series, connect
the black wires coming out of
the board to the connectors
of the first motor’s condenser
and the red wires to the
second motor’s condenser.
Note: série FROG,
connecter les fils noirs qui
sortent de la carte sur les
connecteurs du
condensateur du 1er moteur
et les fils rouges sur le
condensateur du 2emoteur.
Hinweis: Reihe FROG. Die
schwarzen Kabel, die von der
Karte wegführen, an die
Verbinder am Kondensator
vom 1. Motor anschließen,
die roten Kabel an den
Kondensator vom 2. Motor.
Nota: serie FROG, conectar
los hilos negros que salen
de la tarjeta en los
conectores del
condensador del 1° motor
y los hilos rojos en el
condensador del 2° motor.

-13-
HAUPTKOMPONENTEN
1 AnschlußKlemmenleiste
2 Hauptsicherung 5A
3 Schaltkastensicherung 3.15A
4 LED Kontrolleuchte für Stromversorgung mit 24V
5 Code-Speichertasten
6 Trimmer zur Einstellung Laufzeit
7 Trimmer zur Einstellung der Schließautomatik
8 Trimmer zur Einstellung Schließverzögerung Motor 2 und Teilweises Öffnung
9Wählschalter für Funktionen mit 10 Dip (sehen S.14)
10 SteckanschlußFunkfrequenze-Platine (sehen Tabelle)
11 LED Kontrolleuchte zur Anzeige
12 Drehmomentbegrenzer des Motor (sehen S.21)
PRINCIPALES COMPONENTES
1 Caja de bornes las conexiónes
2 Fusibles de línea 5A
3 Fusible para central 3.15A
4 Indicador luminoso de alimentación de 24V
5 Teclas memorización códigos
6 Trimmer de regulación tiempo trabajo
7 Trimmer de regulación tiempo cierre automático
8 Trimmer de regulación retraso cierre 2° motor y apertura parcial
9 Selector de funciones con 10 dip (vedas pag.14)
10 Conexión tarjeta radiofrecuencia (ver tabla)
11 Indicador luminoso
12 Limitador de par motor (ver pág. 21)
MAIN COMPONENTES
1 Terminal block for external conections
2 5A line fuses
3 3.15A central control unit fuse
4 24V power-supply signalling LED
5 Radio-code save buttons
6 Trimmer for adjustment operating time
7 Trimmer for adjustment automatic closing
8 Trimmer for adjustment delay on closing cycle motor n°2 and partial opening
9 10-dip function switch (see p.14)
10 Radiofrequency board socket (se table)
11 Signal LED
12 Motor torque limiter (see pag.21)
PRINCIPAUX COMPOSANTS
1 Plaque à bornes de connexion
2 Fusibles de ligne 5A
3 Fusible boîtier 3.15A
4 LED de signalisation alimentation à 24V
5 Boutons-poussoir mémorisation code radio
6 Trimmer de réglage temps de fonctionnement
7 Trimmer de réglage fermeture automatique
8 Trimmer de réglage retard fermeture moteur 2à et ouverture partielle
9 Selecteur de fonctions à 10 interrupteurs à positions multiples (voir pag.14)
10 Branchement carte radiofréquence (voir tableau)
11 LED de signalisation
12 Limiteur de couple moteur (voir p.21)
ENGLISH
FRANÇAIS
DEUTSCH
ESPANOL

-14-
SELEZIONI FUNZIONI - SELECTION OF FUNCTIONS -SÉLECTION FONCTIONS
FUNKTIONSWAHL - SELECCIÓN DE LAS FUNCIONES
QUADRO COMANDO
FUSIBILI
LINEA 5A
ZA3
CH1
AF
FUSIBILE
CENTRALINA
2A
T.L. T.C.A. TR2M. 2
1 3456 78910O
N
CH2
DIP-SWITCH 10 IE / 10-WAY DIP-SWITCH / DIP-SWITCH 10 OIES
ZEHNWEG-DIP-SWITCH / DIP-SWITCH 10 ÍAS
1 ON Chiusura automatica attivata; (1OFF-disattivata)
2 ON "Apre-stop-chiude-stop" con pulsante (2-7) e radiocomando (scheda AF
inserita) attivata;
2 OFF "Apre-chiude" con pulsante (2-7) e radiocomando (scheda AF inserita)
attivata;
3 ON "Solo apertura" con radiocomando (scheda AF inserita) attivata; (3OFF-
disattivata)
4 ON Prelampeggio in apertura e chiusura attivato; (4OFF-disat.)
5 ON Rilevazione presenza ostacolo attivato; (5OFFdis.)
6 OFF "Uomo presente" (esclude il funzionamento del radiocomando) disattivata;
(6ON - attivata)
7 ON Colpo d'ariete attivato; (per facilitare lo sgancio della serratura) 7OFF-
disattivato
8 OFF - 10OFF Funzione di richiusura in fase di apertura (collegare il dispositivo di
sicurezza sui morsetti 2-CX) attivato;
8 OFF - 10ON Funzione di stop parziale (collegare il dispositivo di sicurezza sui
morsetti 2-CX) attivato;
(se non vengono utilizzati i dispositivi su 2-CX, posizionare il dip 8 in ON)
9 OFF Funzione di riapertura in fasedichiusuraattivato;condispositivodisicurezza
collegato ai morsetti 2-C1, (se non viene utilizzato il dispositivo, selezionare
il dip in ON)
ITALIANO
2
134567
8910
O
N
ON
OFF

-15-
ENGLISH
1 ON Automatic closure enabled; (1OFF-disabled)
2 ON "Open-stop-close-stop"with button (2-7) andradiocontrol(AF board inserted)
enabled;
2 OFF "Open-close" with button (2-7) and radio control (AF board inserted)enabled;
3 ON "Only opening" with radio control (AF board inserted) enabled; (3OFF-
disabled)
4 ON Pre-flashing (opening and closing) enabled; (4OFF-disabled)
5 ON Obstacle detection device enabled; (5OFF - disabled)
6 OFF "Operator present" (radio remote control is deactivated when function is
selected) desabled; (6ON-enabled)
7 ON Hammer movement operation enabled; (this function helps unlock the
electric lock) 7OFF-disabled
8OFF - 10OFF Re-closure during opening (connect the safety device on terminals
(2-CX) enabled;
8OFF - 10ON Partialstop (connect the safety device on terminals (2-CX)enabled;
(if the devices on the 2-CX terminals are not used, set Dip 8 in ON)
9 OFF Re-opening in closing phase (connect the safety device on terminals 2-C1)
enabled; if not used, set the dip-switch to ON.
FRANÇAIS
1 ON Fermeture automatique activé; (1OFF-éteinte)
2 ON "Ouvre-stop-ferme-stop" avec bouton (2-7) et commande-radio (carte AF
insérée) activé;
2 OFF "Ouvre-ferme" avec bouton (2-7) et commande-radio (carte AF insérée)
activé;
3 ON "Soulement ouverture" avec commande-radio (carte AF insérée) activé;
(3OFF-éteinte)
4 ON Preclignotementpandant la phase d'ouvertureetde fermeture activé; (4OFF-
éteinte.)
5 ON Dispositif de détection d'obstacle activé; (5OFF éte.)
6 OFF Fonction avec "homme mort" (exclut la fonction radiocommande) éteinte;
(6ON - activé)
7 ON Fonction coup de bélier activé; (pour faciliter le déblocage de la serrure)
7OFF-éteinte
8OFF - 10OFF Réfermeture en phase d'ouverture(relierledispositif de sécurite aux
bornes 2-CX) activé;
8OFF - 10ON Stop partiel (relier le dispositif de sécurite aux bornes 2-CX) activé;
(si le dispositif sur 2-CX ne sont pas utilisés, positionner le dip 8 sur ON)
9 OFF Réouverture en phase de fermeture activé; relier le dispositif de sécuritèaux
bornes2-C1; s'iln'estpas utilisé,positionnerl'interrupteur àpositions multiples
sur ON.

-17-
QUADRO COMANDO
FUSIBILI
LINEA 5A
ZA3
CH1
AF
FUSIBILE
CENTRALINA
2A
T.L. T.C.A. TR2M. 2
1 3456 78910O
N
CH2
REGOLAZIONI - ADJUSTMENTS -RÉGLAGES - EINSTELLUNGEN - REGULACIONES
ITALIANO
FRANÇAIS
Trimmer T.L. = Regolazione tempo di
lavoro da un minimo di 0”a un massi-
mo di 120”.
Trimmer T.C.A. = Regolazione tempo
di chiusura automatica da un minimo di
1”a un massimo di 120”.
Trimmer TR2M = Regolazione ritardo
in chiusura 2°motore (min. 0”, max.
15”) e contemporaneamente apertura
parziale (min. 0”, max. 30”).
ENGLISH
ESPANOL
DEUTSCH
REGULACIÓN TRIMMERS
EINTELLUNG TRIMMERS
RÉGLAGE TRIMMERS
TRIMME RS ADJUSTME NT
REGOLAZIONE TRIMMERS
T.L. T.C.A. TR2M.
Trimmer T.L. = Adjusts of operating
time from a minimum of 0”to a
maximum of 120”.
Trimmer T.C.A. = Adjusts automatic
closing time from a minimum of 1”to a
maximum of 120”.
Trimmer TR2M = Adjustment delay
during closure of 2nd motor (min. 0”,
max. 15”) and simultaneously partial
opening time (min. 0”, max. 30”).
Trimmer T.L. = Réglage du temps de
fonctionnement d'un minimum de 0ӈ
un maximun de 120”.
Trimmer T.C.A. = Réglage du temps
de fermeture automatique d'un
minimum de 1”àun maximun de 120”.
Trimmer TR2M = Réglage retard en
fermeture 2°moteur (min. 0”, max. 15”)
et en même temps ouverture partielle
(min. 0”, max. 30”).
Trimmer T.L. = Laufzeit mit
mindestens 0”und höchstens 120 “
eingestellt werden kann.
Trimmer T.C.A. = Timer, auf dem die
Verzögerung für das automatische
Schlißen mit mindestens 1”und
höchstens 120”eingestellt werden
kann.
Trimmer TR2M = Einstellung der
Verzögerungszeit vom 2. Motor beim
Schließen (min. 0”, max. 15”) und
gleichzeitig vom Teilöffnen (min. 0”,
max. 30”).
Trimmer T.L. = Regulación tiempo de
trabajo, desde un mínimo de 0”hasta
un máximo de 120”.
Trimmer T.C.A. = Regulación tiempo
de cierre automático, desde un mínimo
de 1”hasta un máximo de 120”.
Trimmer TR2M = Regulación del
retardo durante el cierre del 2°motor
(min. 0”, máx. 15”) y
contemporáneamente apertura parcial
(min. 0”, máx. 30”).

-18-
COLLEGAMENTI ELETTRICI - ELECTRICAL CONNECTIONS - BRANCHEMENTS ÉLECTRIQUES
ELEKRISCHE ANSCHLÜSSE - CONEXIONES ELÉCTRICAS
W
E
U
W
L1
L2
L1 L2 UVWXYEE3 10 11 S 1 2 3 3P 4 5 7 2 C1CX B1B2
Alimentazione quadro comando - 230V (a.c.)
Power supply for control unit - 230V (a.c.)
Alimentation armoire de commande - 230V (c.a.)
Stromversorgung Steuergerät - 230V (Wechselstrom)
Alimentación cuadro de mando - 230V (a.c.)
Collegamento 1 Motore (ritardato in apertura)
Connection for 1 motor (delayed in opening)
Connection du moteur 1 (retardé en ouverture)
AuschlußMotor 1 (verzögertes Ansteuern beim Öffnen)
Conexionado 1 motor (redardo en apertura)
Collegamento 2 Motore (ritardato in chiusura)
Connection for 2 motor (delayed in closing)
Connection du moteur 2 (retardé en fermeture)
AuschlußMotor 2 (verzögertes Ansteuern beim Schließen)
Conexionado 2 motor (redardo en cierre)
Uscita 230V (a.c.)-25W max. in movimento (es. lampeggiato-
re)
230V (a.c.)-25W max. output in motion (e.g. flashing light)
Sortie 230V(c.a.)-25W max. en mouvement (ex.
branchement clignotant)
Ausgang 230V (Wechselstrom) in Bewegung (z.B. Blinker-
Anschluß)
Salida de 230V (a.c.) en movimiento (p.ej. conexión lámpara
intermitente)
X
W
Y
Nel caso si
utilizzi un
solo motore,
collegare
solo il moto-
re n°2 in
uscita X,W,Y.
If only one
reduction gear
is used,
connect only
gear n°2 to the
X,W,Y outlet.
Si on n’utilise
qu’un seul
moteur, ne
brancher que
le moteur n°2
à la sortie
X,W,Y.
Im Fall einer
Inbetriebnahme
mit nur einem
Motor, wird nur
der Motor Nr.2
im Ausgang
X,W,Y.
Si se usa un
sólo motor,
conecte sólo
el motor n°2
en la salida
X,W,Y.

-19-
10
5
E
E3
Collegamento lampada ciclo (230V-60W)
Connection (230V-60W) cycle lamp
Connection lampe cycle (230V-60W)
AnschlußBetriebszyklus-Anzeigeleuchte (230V60W)
Conexionado lámpara ciclo (230V-60W)
Lampada spia (24V-3W max.) "cancello aperto"
(24V-3W max.) "gate-opened" signal lamp
Lampe-témoin (24V-3W max.) "portail ouverture"
Signallampe (24V-3W max.) "Tor Öffnen"
Lampara indicadora (24V-3W max.) "puerta abierta"
Uscita 24V (a.c.) alimentazione accessori (max 20W)
24V (a.c.) output power supply to accessories (max. 20W)
Sortie 24V (c.a.) alimentation accessoires (max 20W)
Ausgang 24V (Wechselstrom) stromversorgung Zubehör
(max 20W)
Salida 24V (a.c.) alimentación accesorios (max 20W)
Collegamento elettroserratura (12V-15W max.)
Connection for electrically-actuated lock: 12V-15W max.
Connexion serrure électrique (12V-15W max.)
AnschlußElektroschloß(12V-15W max.)
Conexión electrocerradura (12V-15W max.)
Pulsante di stop (N.C.)
Stop button (N.C.)
Bouton-poussoir de stop (N.F.)
Stop-Taste (Ruhekontakt)
Tecla de parada (N.C.)
Pulsante apre (N.O.)
Open button (N.O.)
Bouton-poussoir d'ouverture (N.O.)
Taste Öffnen (Arbeitskontakt)
Tecla de apertura (N.O.)
1
2
10
11
11
S
2
3

-20-
Pulsante (N.O.) per apertura parziale (apertura del 2°
motore)
Pushbutton (normally open) partial opening (opens to motor
no. 2)
Bouton-poussoir (N.O.) pour ouverture partielle (ouvertu-
re du 2° moteur)
Drucktaster (Arbeitskontakt) für Teilweises Öffnen (Öffnung
eines einzigen Torflügels über Motor 2)
Tecla (N.O.) para apertura parcial (apertura del 2° motor)
Pulsante chiude (N.O.)
(N.O.) Pushbutton-close
Bouton-poussoir fermeture (N.O.)
Taste Schließen (Arbeitskontakt)
Pulsador de cierre (N.O.)
Collegamento radio e/o pulsante (N.O.) per comandi
(vedi dip-switch 2-3 sel.funzioni)
Contact radio and/or button for control
(see dip-switch 2-3 function selection)
Contact radio et/ou poussoir pour commande
(voir dip-switch 2-3 sel.fonction)
Funkkontakt und/oder Taste Steuerung
(siehe dip-switch 2-3 Funktionswahl)
Contacto radio y/o pulsador para mando
(vedas dip-switch 2-3 seleción función)
Contatto (N.C.) di riapertura in fase di chiusura
Contact (N.C.) for re-opening during closing
Contact (N.F.) de réouverture pendant la fermeture
Ruhekontakt Wiederöffnen beim Schließen
Contacto (N.C.) para la reapertura en la fase de cierre
Uscita contatto (N.O.) Portata contatto: 5A - 24V d.c.
Contact output (N.O.) Resistive load: 5A - 24V d.c.
Sortie contact (N.O.) Portée contact: 5A - 24V c.c.
Ausgang Arbeitskontakt Stromfestigkeit: 5A - 24V Gleichstrom
Salida contacto (N.O.) Carga resistiva: 5A - 24V d.c.
2
3P
2
4
2
7
2
C1
B1
B2

-21-
Contatto (N.C.) di richiusura durante l'apertura
Contact (N.C.) for re-closing during opening
Contact (N.F.) de réfermeture pendant l'ouverture
Runekontakt Wiederschließen beim Öffnen
Contacto (N.C.) de recierre en la fase de apertura
Contatto (N.C.) stop parziale
Contact (N.C.) partial stop
Contact (N.F.) stop partiel
Runekontakt Teilstop
Contacto (N.C.) parada parcial
Collegamento antenna
Antenna connection
Connexion antenne
Antennenanschluß
Conexión antena
2
1345678910O
N
2
1345678910O
N
LIMITATORE DI COPPIA MOTORE - MOTOR TORQUE LIMITER -LIMITEUR DE COUPLE MOTEUR
DREHMOMENTBEGRENZER DES MOTORS - LIMITADOR DE PAR MOTOR
Per variare la
coppia
motore,
spostare il
faston indica-
to su una
delle 4 posi-
zioni; 1 min -
4 max.
To vary the
motor torque,
move the
indicated
faston to one
of the four
positions:
1=min, 4=max
Pour varier le
couple du
moteur,
déplacer le
connecteur
indiqué sur
l'une des 4
positions; 1
min. - 4 max.
Zur Änderung
des Motor-
Drehmoments
den angegeb-
enen Faston
auf eine der 4
Stellungen
positionieren:
1 min. - 4 max.
Para variar el
par motor,
desplazar el
faston indica-
do hasta una
de las 4
posiciones; 1
mín. - 4 máx.
2
CX 8 OFF - 10 OFF
8 OFF - 10 ON
12 3 4
L2T L1T
024 12
QUADRO COMANDO
FUSIBILI
LINEA 5A
ZA3
CH1
AF
FUSIBILE
CENTRALINA
2 A
T.L. T.C.A. TR 2 M. 21 345 67 8910O
N
CH2
12 3 4
L2T L1T
024
12
L1 L2 C T 012 24

-28-
CAME LOMBARDIA S.R.L.___COLOGNO M. (MI)
([phone] ([phone]
CAME SUD S.R.L. _________________NAPOLI
([phone] ([phone]
CAME (AMERICA) L.L.C._________MIAMI (FL)
([phone] ([phone]
CAME AUTOMATISMOS S.A_________MADRID
([phone] ([phone]
CAME BELGIUM____________LESSINES
([phone] ([phone]
CAME CANCELLI AUTOMATICI S.P.A.
DOSSON DI CASIER (TREVISO)
(+39) 0422 ([phone]
CANCELLI AUTOMATICI
CAME FRANCE S.A.___NANTERRE CEDEX (PARIS)
([phone] ([phone]
CAME GMBH____KORNTAL BEI (STUTTGART)
([phone] ([phone]
CAME GMBH________SEEFELD BEI (BERLIN)
([phone] ([phone]
CAME PL SP.ZO.O_________WARSZAWA
([phone] ([phone]
CAME UNITED KINGDOM LTD___NOTTINGHAM
([phone] ([phone]
ASSISTENZA TECNICA
NUMERO VERDE
800 295830
WEB
www.came.it
E-MAIL
[email protected]
SISTEMA QUALITÀ
CERTIFICATO
NOTE - NOTE - NOTE - HINWEIS - NOTA