Cameo P2 FC User manual

P2 FC
FULL COLOUR PROFILE SPOTLIGHT
CLP2FC
USER´S MANUAL
BEDIENUNGSANLEITUNG
MANUEL D`UTILISATION
MANUAL DE USUARIO
INSTRUKCJA OBSŁUGI
MANUALE D‘ USO

CONTENTS / INHALTSVERZEICHNIS / CONTENU / CONTENIDO / TREŚĆ /
CONTENUTO
ENGLISH
INFORMATION ON THIS USER MANUAL 6
INTENDED USE 6
DEFINITIONS AND SYMBOL EXPLANATIONS 6
SAFETY INSTRUCTIONS 7
NOTES FOR MOBILE INDOOR DEVICES 10
INCLUDED 10
INTRODUCTION 11
CONNECTIONS, OPERATING AND DISPLAY ELEMENTS 12
OPERATION 14
INSTALLATION 26
INSTALL FIXED BEAM ANGLE LENSE TUBE 26
CARE, MAINTENANCE AND REPAIR 30
OPTIONAL ACCESSORIES 31
TECHNICAL DATA 33
MINIMUM DISTANCE TO ILLUMINATED SURFACE 35
MINIMUM DISTANCE TO NORMALLY FLAMMABLE MATERIALS 35
DISPOSAL 36
MANUFACTURER’S DECLARATIONS 36
DEUTSCH
INFORMATIONEN ZU DIESER BEDIENUNGSANLEITUNG 38
BESTIMMUNGSGEMÄSSER GEBRAUCH 38
BEGRIFFS- UND SYMBOLERKLÄRUNGEN 38
SICHERHEITSHINWEISE 39
HINWEISE FÜR ORTSVERÄNDERLICHE INDOOR-GERÄTE 42
LIEFERUMFANG 42
EINFÜHRUNG 43
ANSCHLÜSSE, BEDIEN- UND ANZEIGEELEMENTE 44
BEDIENUNG 46
MONTAGE 59
LINSENTUBUS MIT FIXEM ABSTRAHLWINKEL MONTIEREN 60
PFLEGE, WARTUNG UND REPARATUR 63
OPTIONALES ZUBEHÖR 64
TECHNISCHE DATEN 66
MINDESTABSTAND ZUR BELEUCHTETEN FLÄCHE 68
MINDESTABSTAND ZU NORMAL ENTFLAMMBAREN MATERIALIEN 68

ENTSORGUNG 69
HERSTELLERERKLÄRUNGEN 70
FRANÇAIS
INFORMATIONS CONCERNANT CE MANUEL D’UTILISATION 71
UTILISATION CONFORME 71
EXPLICATIONS DES TERMES ET DES SYMBOLES 71
CONSIGNES DE SÉCURITÉ 72
REMARQUES CONCERNANT LES APPAREILS D’INTÉRIEUR MOBILES 75
CONTENU DE LA LIVRAISON 75
INTRODUCTION 76
RACCORDEMENTS, ÉLÉMENTS DE COMMANDE ET D’AFFICHAGE 77
UTILISATION 79
MONTAGE 92
MONTER UN TUBE DE LENTILLE AVEC UN ANGLE DE RAYONNEMENT FIXE 93
ENTRETIEN, MAINTENANCE ET RÉPARATION 96
ACCESSOIRES DISPONIBLES EN OPTION 98
CARACTÉRISTIQUES TECHNIQUES 100
DISTANCE MINIMALE PAR RAPPORT À LA SURFACE ÉCLAIRÉE 102
DISTANCE MINIMALE PAR RAPPORT AUX MATÉRIAUX NORMALEMENT INFLAMMABLES 102
ÉLIMINATION 103
DÉCLARATIONS DU FABRICANT 104
ESPAÑOL
INFORMACIÓN SOBRE ESTE MANUAL DE INSTRUCCIONES 105
USO PREVISTO 105
TÉRMINOS Y SÍMBOLOS 105
INSTRUCCIONES DE SEGURIDAD 106
INDICACIONES PARA EQUIPOS PORTÁTILES DE INTERIOR 109
VOLUMEN DE SUMINISTRO 109
INTRODUCCIÓN 110
CONEXIONES, ELEMENTOS DE MANEJO Y ELEMENTOS DE VISUALIZACIÓN 111
MANEJO 113
MONTAJE 126
MONTAR EL TUBO DE LENTE CON ÁNGULO DE DISPERSIÓN FIJO 127
CUIDADO, MANTENIMIENTO Y REPARACIÓN 130
ACCESORIOS OPCIONALES 132

TECHNICAL DATA 134
DISTANCIA MÍNIMA CON RESPECTO A LA SUPERFICIE ILUMINADA 136
DISTANCIA MÍNIMA CON RESPECTO A MATERIALES NORMALMENTE INFLAMABLES 136
ELIMINACIÓN 137
DECLARACIONES DEL FABRICANTE 138
POLSKI
INFORMACJE DOTYCZĄCE NINIEJSZEJ INSTRUKCJI OBSŁUGI 139
UŻYTKOWANIE ZGODNE Z PRZEZNACZENIEM 139
OBJAŚNIENIA TERMINÓW I SYMBOLI 139
ZASADY BEZPIECZEŃSTWA 140
UWAGI DOTYCZĄCE PRZENOŚNEGO SPRZĘTU DO STOSOWANIA W POMIESZCZENIACH 143
ZAKRES DOSTAWY 143
WPROWADZENIE 144
PRZYŁĄCZA, ELEMENTY OBSŁUGI IWSKAŹNIKI 145
OBSŁUGA 147
MONTAŻ 160
MONTAŻ TUBUSU SOCZEWKI ZE STAŁYM KĄTEM ROZWARCIA WIĄZKI ŚWIETLNEJ 161
CZYSZCZENIE, KONSERWACJA INAPRAWY 164
OPCJONALNE AKCESORIA 166
DANE TECHNICZNE 168
MINIMALNA ODLEGŁOŚĆ OD POWIERZCHNI OŚWIETLANEJ 170
MINIMALNA ODLEGŁOŚĆ OD MATERIAŁÓW NORMALNIE PALNYCH 170
UTYLIZACJA 171
OŚWIADCZENIA PRODUCENTA 172
ITALIANO
INFORMAZIONI SUL PRESENTE MANUALE D’USO 173
UTILIZZO CONFORME 173
SPIEGAZIONE DI CONCETTI E SIMBOLI 173
INDICAZIONI SULLA SICUREZZA 174
AVVERTENZE PER DISPOSITIVI INDUSTRIALI PORTATILI 177
FORNITURA 177
INTRODUZIONE 178
CONNETTORI, ELEMENTI DI COMANDO E VISUALIZZAZIONE 179
UTILIZZO 181
MONTAGGIO 195

MONTAGGIO DEL TUBO PER LENTI CON ANGOLO DI EMISSIONE FISSO 196
PULIZIA, MANUTENZIONE E RIPARAZIONE 199
ACCESSORI OPZIONALI 200
DATI TECNICI 202
DISTANZA MINIMA DALLA SUPERFICIE ILLUMINATA 204
DISTANZA MINIMA DAI MATERIALI NORMALMENTE INFIAMMABILI 204
SMALTIMENTO 205
DICHIARAZIONI DEL PRODUTTORE 206
DMX
DMX CONTROL / DMX STEUERUNG / PILOTAGE DMX / CONTROL DMX /
STEROWANIE DMX / CONTROLLO DMX 207

6
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCHENGLISH
ENGLISH
YOU HAVE MADE THE RIGHT CHOICE!
This device has been developed and manufactured to the highest quality standards to ensure
many years of problem-free operation. Please read this user manual carefully to be able to use
your new Cameo product quickly and optimally. Further information about Cameo Light is avail-
able on our website CAMEOLIGHT.COM.
INFORMATION ON THIS USER MANUAL
• Carefully read the safety instructions and the entire manual before operating the device.
• Observe the warnings on the device and in the user manual.
• Always keep the user manual within reach.
• If you sell or pass on the device, it is important that you also include this user manual, as it is an
integral part of the product.
INTENDED USE
The product is a device for event technology!
This product has been developed for professional use in the field of event technology and is not
suitable for use as domestic lighting!
Furthermore, this product is only intended for qualified users with specialist knowledge of event
technology!
Use of the product outside the specified technical data and operating conditions is considered
inappropriate!
Liability for damage and third-party damage to persons and property due to inappropriate use is
excluded!
The product is not suitable for:
• Use by persons (including children) with limited physical, sensory or mental abilities or lack of
experience and knowledge.
• Children (children must be instructed not to play with the device).
DEFINITIONS AND SYMBOL EXPLANATIONS
1. HAZARD: The word HAZARD, possibly in combination with a symbol, indicates situations in
which there is an immediate danger or risk of potentially fatal injury.
2. WARNING: The word WARNING, possibly in combination with a symbol, indicates situations in
which there is an immediate danger or risk of potentially fatal injury.
3. CAUTION: The word CAUTION, possibly in combination with a symbol, indicates situations or
conditions that could result in injury.
4. ATTENTION: The word ATTENTION, possibly in combination with a symbol, indicates situations
or conditions that could result in damage to property and/or the environment.

7
DMX DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
This symbol identifies hazards that can cause electric shock.
This symbol identifies hazardous areas or hazardous situations.
This symbol indicates hazards caused by hot surfaces.
This symbol indicates hazards caused by intense light sources.
This symbol indicates a device in which there are no user-replaceable parts.
This symbol indicates additional information on the operation of the product.
SAFETY INSTRUCTIONS
HAZARD:
1. Do not open the device and do not carry out any modifications.
2. If your device no longer functions properly, if liquids or objects get inside it or if it
has been damaged in any other way, switch it off immediately and unplug it from
the power source. The device may be repaired only by authorised repair techni-
cians.
3. For devices of protection class 1, the protective conductor must be connected
correctly. Never disconnect the protective conductor. Devices of protection class 2
do not have a protective conductor.
4. Ensure that live cables are not kinked or otherwise mechanically damaged.
5. Never bypass the device fuse.
WARNING:
1. The device may not be operated if it shows obvious signs of damage.
2. The device may only be installed in a voltage-free state.
3. If the device's power cable is damaged, the device may not be used.
4. Permanently connected power cables may only be replaced by a qualified person.

8
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCHENGLISH
ATTENTION:
1. Do not switch on the device if it has been exposed to extreme temperature fluctu-
ations (for example, following transport). Moisture and condensation can damage
the device. Switch on the device only when it has reached room temperature.
2. Ensure that the voltage and frequency of the mains supply match the values spec-
ified on the device. If the device has a voltage selector switch, do not connect the
device until it has been set correctly. Use only suitable power cables.
3. To disconnect the device from the mains on all poles, it is not sufficient to press the
on/off switch on the device.
4. Make sure that the fuse used corresponds to the type printed on the device.
5. Ensure that suitable measures have been taken against overvoltage (e.g. lightning
strikes).
6. Observe the specified maximum output current on devices with a Power Out con-
nection. Ensure that the total current consumption of all connected devices does
not exceed the specified value.
7. Replace plug-in power cables with original cables only.
HAZARD:
1. Choking hazard! Plastic bags and small parts must be kept out of reach of persons
(including children) with reduced physical, sensory or mental capabilities.
2. Risk of falling! Make sure that the device is securely installed and will not fall
down. Only use suitable stands or mounts (particularly for fixed installations).
Ensure that accessories are properly installed and secured. Ensure that applicable
safety regulations are observed.
WARNING:
1. Use the device in the prescribed manner only.
2. Operate the device using only accessories of the type recommended and supplied
by the manufacturer.
3. Observe safety regulations applicable in your country during installation.
4. After connecting the device, ensure that all cables are routed so as to avoid dam-
age or accidents, such as from tripping.
5. Always observe the specified minimum distance to normally flammable materials!
Unless explicitly stated, the minimum distance is 0.3m.

9
DMX DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
CAUTION:
1. Moving components such as mounting brackets may become jammed.
2. In the case of devices with motor-driven components, there is a risk of injury due
to the movement of the device. Sudden movement of the device can cause shock
reactions.
3. The housing surface of the device can become very hot during regular operation.
Ensure that accidental touching of the housing is not possible. Always allow the
device to cool sufficiently before removal, maintenance work and charging etc.
ATTENTION:
1. Do not install or use the device in the vicinity of radiators, accumulators, stoves, or
other heat sources. Ensure that the device is always installed in such a way that it
is sufficiently cooled and cannot overheat.
2. Do not place any ignition sources, such as burning candles, near the device.
3. Ventilation openings must not be covered and fans must not be blocked.
4. For transport, use the original packaging or packaging provided by the manufactur-
er.
5. Avoid any impacts to or shaking of the device.
6. Observe the IP rating and the ambient conditions such as temperature and humidi-
ty according to the specifications.
7. Devices can be continuously further developed. In the event of deviating informa-
tion on operating conditions, performance or other device properties between the
user manual and the device labelling, the information on the device always has
priority.
8. The device is not suitable for tropical climate zones or for operation over 2,000 m
above sea level.
9. Unless explicitly stated, the device is not suitable for operation under marine
conditions.
PLEASE NOTE:
For conversion or retrofit sets or accessories provided by the manufacturer, it is
essential to observe the instructions included.

10
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCHENGLISH
CAUTION! IMPORTANT INFORMATION REGARDING LIGHTING PRODUCTS!
1. Never look directly into the beam of light, not even for a short period of time.
2. Never look into the beam of light using optical devices such as a magnifying glass.
3. Stroboscopic effects may cause epileptic seizures in susceptible individuals!
4. Permanently installed lamps are built into these lighting units. These may not be
replaced by the user. The lamps contained in this lighting unit may only be replaced
by the manufacturer, its service partner, or a similarly qualified person.
NOTES FOR MOBILE INDOOR DEVICES
1. Temporary operation! Event equipment is generally only designed for temporary
operation.
2. Continuous operation or permanent installation can impair the functioning of the
device and cause premature ageing.
INCLUDED
Remove the product from the packaging and remove all packaging material.
Please check the completeness and integrity of the delivery and notify your distribution partner
immediately after purchase if the delivery is not complete or if it is damaged.
Product includes:
X1 x CLP2 Full Colour profile spotlight (without lens tube)
X1 x soft edge filter
X1x power cable
XUser manual
A lens tube is NOT included in the spotlight’s scope of delivery. Tubes with lenses of
different beam angles are available separately. Do NOT operate the spotlight without
the lens tube.

11
DMX DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
INTRODUCTION
RGBAL profile spotlight
CLP2FC
CONTROL FUNCTIONS:
1CH DIM, 2CH DIM 16Bit, 2CH CCT, 3CH RGB, 5CH RGBAL, 4CH CCT, 6CH HSI-CCT, 7CH RGB-CCT,
11CH Direct CCT, 10CH RGBAL 16Bit, 10CH HSI-CCT, 18CH Full Access DMX control
Master/slave operation
Standalone operation
W-DMX™ (with optional iDMX stick, product number CLIDMXSTICK)
EZ Remote (with optional Cameo UNICON, product number CLIREMOTE)
FEATURES:
230 W 5-in-1 RGBAL COB LED. DMX512. W-DMX™ optional. 5-pin DMX connections. Quicklight
via rotary-push encoder. Operating voltage: 100–240 V AC.
The spotlight features the RDM standard (Remote Device Management). Remote device manage-
ment allows the user to view the status and configuration of RDM terminals via an RDM-capable
controller, such as the optionally available Cameo UNICON (product number CLIREMOTE).
Cameo UNICON also provides access to the entire spotlight menu.

12
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCHENGLISH
CONNECTIONS, OPERATING AND DISPLAY ELEMENTS
1
3
4 5
6
7
8 9 10
2
1POWER IN
TRUE1-compatible mains input socket. Operating voltage 100–240 V AC/50–60 Hz.
A suitable power cable with TRUE1 compatible plug is included.
2POWER OUT
TRUE1-compatible mains output socket. Facilitates power supply to other CAMEO spotlights.
Ensure that the total power consumption of all devices connected to the device does not exceed
the given ampere (A) value.

13
DMX DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
3FUSE
Fuse holder for 5 x 20 mm fuses. IMPORTANT: Replace the fuse only with a fuse of the same type
and value. In the event of repeated fuse failure, please contact an authorised service centre.
4DMX IN
Male 5-pin XLR socket for connection to a DMX control device (e.g. DMX console).
5DMX OUT
Female 5-pin XLR socket for sending the DMX control signal.
6IDMX STICK
Connection for the optional iDMX stick for W-DMX™ connection (plug in the iDMX stick with the
antenna facing upwards).
7OLED DISPLAY
The OLED display shows the currently activated mode (main display), the menu items in the menu
and the numerical value or operational status in certain menu items. If there is no input for around
two minutes, the display automatically returns to the main display. Note regarding the main
display in operating modes with external control: As soon as the control signal is interrupted, the
characters in the display begin to flash. When there is a control signal again, the flashing stops.
8DIM / ENTER / SELECT
Rotary-push encoder for the adjustment and control of the spotlight.
DIM - In the standalone modes CCT, HSI, DIRECT LED, GEL, User Colour and Play Loop, the encod-
er has the function of the master dimmer (rotate encoder).
ENTER - 1. Press ENTER to access the menu level to select the mode. 2. You move down one level
in the menu structure. 3. You can confirm a value or status or value change, such as changing the
DMX start address, by pressing ENTER.
SELECT - Turn the encoder to SELECT the menu items on the menu level and change the status
or a value in a menu item (e.g. DMX start address).
9MIDDLE ENCODER
The function of the middle push-button rotary encoder (turn and press) is shown in the corre-
sponding menu item in the centre of the display (centre line = turn, bottom line = press).
10 ESC
If the press function of the right push button rotary encoder is not explicitly shown at the bottom
right of the display, pressing the encoder has the function of moving up one level in the menu
structure.

14
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCHENGLISH
OPERATION
NOTES
• As soon as the spotlight is correctly is connected to the power supply, the following will be
displayed in succession: “Welcome to Cameo”, the model name and the software version. After
this process, the lamp is ready for operation and starts in the previously enabled mode.
• If one of the DMX modes or slave mode is enabled and there is no control signal at the DMX
input, the characters in the centre line of the display will start to flash.
• If no input is made within approximately 1 minute, the currently activated mode is automatical-
ly shown in the display (main display).
DISPLAY MAIN DISPLAY DMX MODE
The main display in DMX mode shows the currently set DMX start address, DMX mode and further
information (see illustration).
DMX | DMX | Auto
DMX Address 001
5CH RGBAL
Mode Menu
Status = DMX signal present = no DMX signal
Currently activated operating mode Fan mode
DMX start address and
DMX mode
Press encoder =
select mode (mode)
Press encoder =
Open main menu (Menu)

15
DMX DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
SETTING DMX START ADDRESS (DMX address)
Starting from the main display, press the right rotary-push encoder to enter the main menu. Ro-
tate the left encoder (SELECT) to select the menu item DMX Address (see left arrow) and confirm
by pushing the encoder (ENTER). You can now configure the DMX start address as required by ro-
tating the left encoder (the highest value depends on the selected DMX mode). At the same time,
the following DMX start address (following address) is displayed for the selected start address
plus channel number of the selected DMX mode. Confirm the entry by pressing the left encoder
(ENTER), which will also automatically return you to the main display and activate DMX mode. The
menu item for selecting the desired DMX mode can be reached directly from the DMX Address
menu item by pressing the middle rotary-push encoder (DMX mode); the previously set DMX start
address is automatically saved.
Rotate encoder =
change value
Press encoder =
confirm value change (Enter)
Press encoder =
Open main menu (Menu)
Press encoder =
select of DMX mode
DMX Address
001 (5CH of Mode)
following Address 006
Enter DMX-Mode Menu
CONFIGURING DMX MODE (DMX Mode)
Starting from the main display, press the right rotary-push encoder to enter the main menu.
Rotate the left encoder (SELECT) to select the menu item DMX Mode (see left arrow) and confirm
by pushing the encoder (ENTER). You can now select the desired DMX mode by turning the left
encoder. Confirm the selection by pressing the left encoder (ENTER), which will also automatically
return you to the main display and activate DMX mode. Tables with the channel assignment of the
different DMX modes can be found in these instructions under DMX CONTROL.
1CH DIM
2CH DIM 16Bit
2CH CCT
3CH RGB
5CH RGBAL
4CH CCT
6CH HSI-CCT
7CH RGB-CCT
11CH Direct CCT
10CH RGBAL 16Bit
10CH HSI-CCT
18CH Full Access
DMX Mode
Menu

16
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCHENGLISH
STANDALONE MODE ‘CCT’ (Correlated Colour Temperature)
Starting from the main display, press the left push button rotary encoder to access the menu for
selecting the mode. Rotate the left encoder (SELECT) to choose CCT mode (see left arrow) and
confirm by pressing the left encoder (ENTER). Set the brightness (DIM), colour temperature (CCT)
and colour shade (Tint) by turning the three rotary-push encoders (see illustration).
CCT | Auto
DIM CCT Tint
100% 3000K 0.0
Mode Menu
Rotate encoder =
set brightness (DIM)
Press encoder =
select operating mode (Mode)
Rotate encoder =
set colour (Tint)
Press encoder =
open main menu (menu)
Rotate Encoder =
set colour temperature (CCT)
STANDALONE MODE ‘HSI’ (Hue - Saturation - Intensity)
Starting from the main display, press the left push button rotary encoder to access the menu for
selecting the mode. Rotate the left encoder (SELECT) to choose HSI (see left arrow) and confirm
by pressing the left encoder (ENTER). Set the brightness (DIM), colour shade (HUE) and saturation
(SAT) by turning the three rotary-push encoders (see illustration).
HSI | Auto
DIM HUE SAT
100% 360 100
Mode Menu
Rotate encoder =
set brightness (DIM)
Press encoder =
select operating mode (Mode)
Rotate encoder =
set colour saturation (SAT)
Press encoder =
open main menu (menu)
Rotate Encoder =
set colour (HUE)

17
DMX DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
STANDALONE MODE DIRECT LED (RGBAL colour mixing)
Starting from the main display, press the left push button rotary encoder to access the menu for
selecting the mode. Turn the left encoder (SELECT) to choose DIRECT LED (see left arrow) and
confirm by pressing the left encoder (ENTER). Now adjust the overall brightness (DIM) and the
intensity of R, G, B, A and L, and strobe effect (Strobe) using the three rotary-push encoders (see
illustration).
Rotate encoder =
set brightness (DIM)
Press encoder =
select operating mode (Mode)
Rotate encoder =
adjust brightness of G or An
or strobe
Press encoder =
open main menu (menu)
Rotate encoder =
set brightness of R or B or L
Press encoder =
toggle between R+G and B+A and L+Strobe (Colour)
DIRECT LED | Auto
DIM R G
100% 255 255
Mode Colour Menu
STANDALONE MODE GEL (colour filter presets)
Starting from the main display, press the left push button rotary encoder to access the menu
for selecting the mode. Turn the left encoder (SELECT) to choose GEL mode (see left arrow) and
confirm by pressing the left encoder (ENTER). Now set the brightness (DIM) and colour filter preset
(GEL) using the left and middle rotary-push encoder (see illustration). The colour filter presets with
the Lee filter designations and the corresponding Rosco filter numbers can be found in the DMX
tables under DMX CONTROL (18-channel mode, channel 16 “Colour Presets” without “User Colour
1–8”).
Rotate encoder =
set brightness (DIM)
Press encoder =
select operating mode (Mode)
Press encoder =
open main menu
Rotate Encoder =
select filter preset
GEL | Auto
DIM GEL
100% Plasa Red
Mode Menu

18
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCHENGLISH
STANDALONE MODE USER COLOUR (individual colour presets 1–8)
Starting from the main display, press the left push button rotary encoder to access the menu for
selecting the mode. Turn the left encoder (SELECT) to choose User Colour mode (see left arrow)
and confirm by pressing the left encoder (ENTER). Now select one of the 8 pre-programmed but
individually editable colour sequences (USER_COLOUR_1 to USER_COLOUR_8) by turning the left
encoder. Confirm your selection by pressing the left encoder (ENTER). Now adjust the brightness
(DIM) of the colour preset using the left encoder (see figure). Individual preset settings and the
renaming of presets can be made in the Edit User Colour menu item.
User Colour | Auto
Mode Back Menu
Rotate encoder =
set brightness (DIM)
Press encoder =
select operating mode (Mode)
Press encoder =
open main menu
Rotate encoder =
toggle between R+G+B+A and G+B+A+L
Press encoder =
back to preset selection (Back)
EDIT USER COLOUR (Edit USER COLOUR)
Starting from the main display, press the right rotary-push encoder to enter the main menu.
Rotate the left encoder (SELECT) to choose the Edit User Colour menu item (as indicated by the
selection arrow on the left) and confirm by pressing the left encoder (ENTER). You can now select
one of the 8 user colours by turning the left encoder and confirming the selection by pressing the
left encoder (ENTER).
USER_COLOUR_1
USER_COLOUR_2
USER_COLOUR_3
USER_COLOUR_4
USER_COLOUR_5
USER_COLOUR_6
USER_COLOUR_7
USER_COLOUR_8
Edit User Colour
Menu

19
DMX DEUTSCHFRANCAIS
ESPAÑOL ENGLISH
ITALIANO POLSKI
Now give the preset an individual name, up to 12 characters long (Edit user Colour Name), by
turning the left encoder to select a letter, underscore or number for the first character of the
name and confirm by pressing the left encoder. This is followed by the input for the second digit
and so on. When the name is complete, press the middle encoder (Save&Next) to go to the next
processing step. If you press “Save&Next” before selecting a letter, underscore or number for the
first digit, the previous preset name will be retained and you will immediately be taken to the next
processing step.
A
...
Z
_
0
...
9
Edit User Colour Name
Save&Next ESC
Now decide how you want to create the colour for the preset, choose between the 4 methods
CCT, HSI, DIRECT and GEL by turning the left encoder (SELECT) and confirm by pressing the left
encoder (ENTER).
Set Colour Via CCT
Set Colour Via HSI
Set Colour Via DIRECT
Set Colour Via GEL
Edit User Colour
Now set the desired colour, as described in the instructions for the respective standalone mode,
and press the left encoder (ENTER/Save) to confirm.
Edit User Colour Via CCT
DIM CCT Tint
100% 3000K 0.0
Save Menu
Edit User Colour Via HSI
Save Menu
DIM HUE SAT
100% 360 100
Edit User Colour Via GEL
Save Menu
Edit User Colour Via DIRECT
Save Color Menu
DIM R G
100% 255 255
DIM GEL
100% Plasa Red

20
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCHENGLISH
STANDALONE MODE PLAY LOOP(8-step colour sequences 1–8)
Starting from the main display, press the left push button rotary encoder to access the menu for
selecting the mode. Rotate the left encoder (SELECT) to SELECT Play Loop (see left arrow) and
confirm by pressing the left encoder (ENTER). Now select one of the 8 pre-programmed but indi-
vidually editable colour sequences by turning the left encoder. Confirm your selection by pressing
the left encoder (ENTER). The brightness (DIM) of the colour sequence is now set using the left
encoder, the step duration (t-Step, 0.1 seconds to 21 minutes and 2 random modes) and the fade
time (t-Fade, 0 seconds to 18 minutes and 2 random modes) using the middle and right encoders
(see illustration). The individual settings and renaming of the colour sequences can be done in the
Edit Loop menu item in the main menu.
Rotate encoder =
set brightness (DIM)
Press encoder =
select operating mode (Mode)
Rotate encoder =
Set fade time (t-fade)
Press encoder =
open main menu
Rotate encoder =
set step time (t-step)
Press encoder =
back to loop selection
Play Loop | Auto
DIM t-Step t-Fade
100% 4s 3s
Mode Back Menu
EDIT LOOP (Edit Loop)
Starting from the main display, press the right rotary-push encoder to enter the main menu. Turn
the left encoder (SELECT) to choose the Edit Loop menu item (as indicated by the selection arrow
on the left) and confirm by pressing the left encoder (ENTER). Now you can select one of the 8
colour sequences by turning the left encoder and confirming the selection by pressing the left
encoder (ENTER).
LOOP_1
LOOP_2
BAVARIAN
TV SIMULATION
DISCO SIMULATION
FIRE SIMULATION
WARNING LIGHTS
TRAFFIC FLASH
Edit Loop
Menu
Now give the colour sequence an individual name, up to 12 characters long (Edit Loop Name),
by turning the left encoder to select a letter, underscore or number for the first character of the
name and confirm by pressing the left encoder. This is followed by the input for the second digit
and so on. When the name is complete, press the middle encoder (Save&Next) to go to the next
processing step. If you press “Save&Next” before selecting a letter, underscore or number for the