Campania Genesis II User manual

F
T
-
73
GenesisII
Fou
ntain
Two people are recommended for the installation ofthisfountain!
R
evised
March31, 2017
-WINTERCARE-
Fountainbowls/topsandotherfountaincomponents,whichcollect water, shouldnotbeleftoutsideinthewinter since anycomponent,
whichfillswithwater andfreezesmaycrack.Likewise, componentssuchaspedestals,whichremaininabasin,filledwithwater,
whichthenfreezes,mayalsocrackor crumble. Ideally, therefore, afountainshouldalwaysbestoredindoorsor inadryprotected
place suchasacoveredporchawayfromtheelements. However, ifafountainmustbeleftoutside:
(1) Removepump, rubber stoppers, drainpipes, finials,andother smallcomponentsfor storageindoors. Note that stoppersor
drainpipesareremovedtoallowdrainageintheeventwater accumulatesinanybasin.
(2) Raisefountainbasefromgroundwithwood stripssothat basewill notfreeze tothegroundsurface.
(3) Cover or wrapthefountainwithburlapor other absorbentmaterial (oldblanket or towel) andthencover securelywith
plastic,making surethat water will notaccumulate inthebasinor other fountaincomponentandfreeze;
(4) Checkfountainperiodicallytoensurethatplastic issecureandwater isnotaccumulating inanyfountaincomponent.
-GENERALFOUNTAINTIPS-
Install fountainsonalevel surface. Youwill needaproperlygrounded110-volt (AConly) GFCI protectedreceptaclenear the
fountainfor your pump. All pumpsaresubmersible andmustbecompletelyunderwater tofunctionproperly. Testall pumpsand
adjusttofull outputprior toassembly. Itisnotrecommendedthat fountainsbeplaceddirectlyongrass or dirt. Positionthechannel
opening at thebaseofeachfountaintoward theelectrical outlet tobeusedsince thepump
cord willbethreadedthroughthisopening.
CheckoutYouTubefor a“Howto”video.
For moreCampania product informationvisit www.campaniainternational.com
All of ourcaststone is proudly
Pump KitPartsList
PK140 pump (1)
#10 stopper(1)
Approx.15”length of½”Blacknon-kinktubing (1)
Wedges(2)
Hose clamps(3)
*Hoseclamps maybe used asflow restrictors
FOUNTAININFORMATION:
Thisfountain holdsapproximately6gallonsof water.
Thisfountain usesasmallfountain cover.
(FTNCOV-SM)
Compatible with#10 Refill Device and LEDKits
(Aspecialstopper isrequiredtousethe refill kit for
thisfountain.)
TOOLSREQUIRED:
Bubble Level
PUMPINFORMATION:
PF140 - 140GPH Pump
6FTcord length

F
T
-
73
GenesisII
Fou
ntain
Two people are recommended for the installation ofthisfountain!
R
evised
March31, 2017
Assemble yourfountain on a levelsurface capable ofholdinga minimumof343 poundswith an approximate2 square
footfootprint.
FT-73C (188lbs)
27”Lx18”Wx8.25”H
FT-73B (12lbs)
5.5”Lx7.25”Wx5.5”H
FT-73A(90 lbs)
16”Lx16”Wx12”H
FT-73BB(2lbs)
4.5”Lx1.25”Wx3.75”H
1. Positionthe basin(FT-73C)where the fountainisto be installed, ensuring
thatitislevel.
2. Assemble the fountain plumbing
a. Usingahoseclamp, attachthe1/2”non-kinktubingtothepumpoutlet.
b. Place thestopper aroundthepumpcord approximately6”fromthepump.
3. Feed the pump cordallthe waythrough the hole inthebasin and run the
cordthrough the channelinthe bottomto ensurethe fountain will be level.
4. FIRMLY press the stopperintothe hole evenly.
a. Note:Usingthehandle ofascrewdriverorhammerworksbestto
pressthe stopperin place.
5. Placethe pump cover(FT-73B)overthe pump. Ensure itisplaced properly
and leveled.
6. Positionthe waterfeature (FT-73A)overthe pump cover.
7. Secure the looseend ofthenon-kinktubingto the pipe protrudingfromthe
bottomofthe waterfeature(FT-73A).
8. Ensurethe waterfeature iscentered and leveled on thepump cover.
9. Placethe pump coverdoor(FT-73BB)inthe pump access openingofthe
pump cover.
10. Fillthe fountain with water.