Camsat CDS-6IP MULTI POE User manual

www.camsat-cctv.com
Wireless video and audio transmission system
for 4 IP PoE cameras in the band 5.1 - 5.8 GHz
QUICK START
ver. 1.1
LINK INFORMATION
It contains basic information about the settings of the radio module eg. the
name of the radio link, signal strength and a list of connected radio transmitters.
CAMERA CONNECTION SETTINGS
Wireless – Contains settings of radio link eg. transmission type (Master / Slave),
the frequency of the operating channel, the name of the SSID link,
signal strength, transmission coding.
Network Settings – Contains settings of IP networks.
1. Website panel menu tree
Time Zone Setting - set the time, the NTP server
System Log - an overview of recent actions and changes in the CDS-6IPMulti
Upgrade Firmware - Software Update
Backup/Restore - save / restore configuration of system
ADVANCED SETTINGS
7. The recommended configuration settings:
a) Change the password to log on to the web panel WWW
(ADVANCED SETTINGS/PASSWORD)
b) Enter the password of radio transmission encryption - a recommended coding
WAP2-PSK (CAMERA CONNECTION SETTINGS/WIRELESS)
c) Scan free channels – set the receiver at the operating mode Slave
Save and press Scan Masters to scan the busy channels.
With this information, you will learn which channels in a given area are free or the
least busy. In the absence of available operating channels it is allowed to use
multiple radios on the same channel, then choose a channel of the weakest signal
(below <-65dB)
8. Testing the radio link.
The last step is to check the correctness of transmission between devices.
These steps must be repeated for each unit transmitting / receiving sequentially
connecting them to a computer
EUEU
POLISH
MARK
POLISH
MARK
Password -
14 Full instructions can be found at: http://camsat-cctv.com/cds-6ipmultiFull instructions can be found at: http://camsat-cctv.com/cds-6ipmulti
The last step is to check the correctness of transmission between devices.
To check the status of connected devices CDS-6IPMulti such as power signal, connec-
tion time, speed, IP address, etc. you must enter the LINK INFORMATION.
To view an updated list of current connections, click the Refresh button at the bottom
or press F5. The appearance of list of MAC addresses of broadcasting units in the
receiver indicates the correctness of the radio configuration. To be sure disconnect
from the transmitting unit from computer and connect the IP camera.
If the devices communicate with receiver it means that the radio connection is
properly configured and running. In the browser address bar enter the IP address of
the camera and check the quality of image transmission. You can now assembly units
at the facility.
TECHNICAL
SUPPORT
tel.[phone]
Mon–Fr 8.00 AM–4.00 PM
NOTE: Before first use, it is necessary to check the full user manual
Full user manual can be found at: www.camsat-cctv.com
changing the password

2. Default settings
3. Description of the connectors and LEDs
4. Preparing for operation
CDS-6IPMulti device can be connected to the power supply in two ways
Connect the radio module to the LAN adapter with the computer set
IP address of the family 192.168.1.XX. (Eg. 192.168.1.99)
6. Necessary configuration settings - required:
a) Log on to the radio module CDS-6IPMulti (default: 192.168.1.1,
Username: CAMSAT, Password: CAMSAT).
b) Set the destination IP address of the radio module.
c) Set the mode Master (Receiver-Recorder) or slave (transmitter - camera).
d) In the receiver (Master) set the no of target operating channel. It is recommended
to choose a specific number of free channel permanently. AUTO DFS function
(automatic channel selection) starts by selecting the AUTO mode in the "Band" and
the AUTO in "Channel” position.
e) In the transmitter (Slave), press the Scan Masters to find names of radio link SSID
of a given receiver. Select the name of the link SSID and press Connect.
Repeat this step for all transmitters (Slave) to be connected to the receiver (Master)
f) correctly connected transmitters should be visible in the list of linked devices tab
in System Information / Wireless clients
g) In the transmitters set the real distance between the transmitter and receiver.
In the receiver, set the distance of the furthest transmitter.
h) Check the connection between the transmitter and the receiver in the tab,
cameras and DVR by PING.
QUICK START
Option 1 - directly from the power supply 12-48V.
Option 2 - CDS-6IPMulti powered from adapter PoE48V.
DESCRIPTION OF CONNECTORS AND LED INDICATORS
POWER IN 12-48V - input DC or AC (the red POWER LED indicates the appearance
of voltage on the connector)
POWER IN 48V - power supply input used only to power the device with another switch or
PoE power supply (the red POWER LED indicates the appearance of voltage on the connector)
CAMERA 4/LAN – LAN port to power IP camera (PoE 48V) or device configuration.
PoE voltage on output is controlled by above switch (the value of voltage is shown by
red-green LED PoE ON/PoE OFF; blinking LINK diode shows data transfer status)
CAMERA 3 – LAN port to power the IP camera (PoE 48V) ((the red POWER LED indicates
the appearance of voltage on the connector; blinking LINK diode shows data transfer status)
CAMERA 2 – LAN port to power the IP camera (PoE 48V) ((the red POWER LED indicates
the appearance of voltage on the connector; blinking LINK diode shows data transfer status)
CAMERA 1 – LAN port to power the IP camera (PoE 48V) (the red POWER LED indicates
the appearance of voltage on the connector; blinking LINK diode shows data transfer status)
5. Connecting to a computer
Parameter
Username
Password
Name of device
Working mode
IP address
Subnet mask
Gateway
Country/Region
Channel number
camsat
camsat
CDS-6IPeco
Video Bridge
192.168.1.1
255.255.255.0
0.0.0.0
ETSI/EU
Auto (DFS)
Default factory settings
WARNING
Before connecting the computer to the CAMERA 4 / LAN switch off
PoE voltage of 48V with the switch placed beside.
48V voltage can damage the non-compatible devices!
www.camsat-cctv.com
Full instructions can be found at: http://camsat-cctv.com/cds-6ipmulti Full instructions can be found at: http://camsat-cctv.com/cds-6ipmulti
2 3
Do not use AUTO channel settings. Be sure to select the channel number
on a permanent according to the current network bandwidth consumption.
Warning
!
Note: The device manufacturer is not responsible for the devices that are not properly
protected and for related damage of the equipment and other network infrastructure
Warning
!