Camsat TCO 5807m User manual

a. Products, that has been operated in contrary to their instruc-
tions or their use.
b. Mechanical and chemical damages.
c. Any claims to technical parameters as long as they were
consistent with those indicated by the manufacturer.
5. All questions not settled in this Warranty shall be governed by provi-
sions of Polish Civil Code.
Old equipment disposal :
1. When the following crossed out wheeled waste-bin symbol
is attached to your product, it does mean the product was
covered by the 2002/96/EC European Directive.
2. All electric and electronic products shall be disposed sepa-
rately from municipal wastes, using special dedicated loca-
tions for these purposes, advised by the government or lo-
cal authorities.
3. Proper disposal of old equipment shall help in prevention of
negative effects to the heath and environment.
4. To get more information on methods of disposal of old
equipment, you should contact the competent local authori-
ty, or company dealing with waste disposal, or the seller
you bought the equipment from.
CAMSAT
www.camsat-wireless.com
TCO 5807m
7-channel 5.8GHz
Video Transmitting-Receiving Set
Designed for wireless video ( PAL or NTSC) transmission over the radio-link on
ISM 5,8GHz band. It supports 7 video channels (5725MHz to 5875MHz). Each
channel has factory defined operating frequency It has one video input and 2 audio
input/output.
TCO5807m consists of :
•TCO 5807m (Tx ) - video / audio transmitter x 1pcs.
•TCO 5807m (Rx) - video / audio receiver x 1pcs.
•Stub omnidirrectional antenna AP05 x 2 pcs.
SPECIFICATION:
Frequency band 5,725 ÷5,875 GHz
Power < 14dBm
Modulation FM
Input/Output VIDEO - 75 Ω/ AUDIO - 600 Ω
Antenna input Female SMA 50 Ω
Power supply 9 ÷13V / 500mA DC
Operating temperature 0 °C ÷+ 55 °C
Dimensions WxHxD Tx: 50x68x25 mm Rx: 50x82x25mm
Range 200m – with stub antennas
Weight 0,2 kg x 2pcs
a. Products, that has been operated in contrary to their
instructions or their use.
b. Mechanical and chemical damages.
c. Any claims to technical parameters as long as they
were consistent with those indicated by the manufac-
turer.
5. All questions not settled in this Warranty shall be governed by
provisions of Polish Civil Code.
Old equipment disposal :
1. When the following crossed out wheeled waste-bin symbol
is attached to your product, it does mean the product was
covered by the 2002/96/EC European Directive.
2. All electric and electronic products shall be disposed sepa-
rately from municipal wastes, using special dedicated loca-
tions for these purposes, advised by the government or lo-
cal authorities.
3. Proper disposal of old equipment shall help in prevention of
negative effects to the heath and environment.
4. To get more information on methods of disposal of old
equipment, you should contact the competent local authori-
ty, or company dealing with waste disposal, or the seller
you bought the equipment from.
CAMSAT
www.camsat-wireless.com
TCO 5807m
7-channel 5.8GHz
Video Transmitting-Receiving Set
Designed for wireless video ( PAL or NTSC) transmission over the radio-link on
ISM 5,8GHz band. It supports 7 video channels (5725MHz to 5875MHz). Each
channel has factory defined operating frequency It has one video input and 2 audio
input/output.
TCO5807m consists of :
•TCO 5807m (Tx ) - video / audio transmitter x 1pcs.
•TCO 5807m (Rx) - video / audio receiver x 1pcs.
•Stub omnidirrectional antenna AP05 x 2 pcs.
SPECIFICATION:
Frequency band 5,725 ÷5,875 GHz
Power < 14dBm
Modulation FM
Input/Output VIDEO - 75 Ω/ AUDIO - 600 Ω
Antenna input Female SMA 50 Ω
Power supply 9 ÷13V / 500mA DC
Operating temperature 0 °C ÷+ 55 °C
Dimensions WxHxD Tx: 50x68x25 mm Rx: 50x82x25mm
Range 200m – with stub antennas
Weight 0,2 kg x 2pcs
www.cctvireland.ie
Lo-Call 1890 866 900
[email protected]

ASSEMBLY:
Mount transmitter on a stable basis using screws. Screw antenna or antenna
wire into antenna port SMA. Place antenna in direct visibility of receiving
point to get best possible quality of transmission. (Note: Transmitter`s an-
tenna has to be in a line of sight of receiver`s antenna). Mount receiver ac-
cording to above instructions.
Connect video signal cables and power supply cables according to descrip-
tions on the PCB. Set required channel according to the Table below. The
polarity and channel number must be same for both interacting trans-
mit/receive devices. There is the adjusting potentiometer within transmitting
part for setting the video-contrast, which enables proper matching of signal
source connected.
RECOMMENDATIONS :
1. Bigger systems, using more then one set should be started one after another (not
all in the same time).
2. Due to causing clutter we do not recommand using pulse power supply
adaptors different to the one recommended by manufacturer f.e. ZS12/1A.
3. Recommended power supply adapter: transformer, stabilized, 12V not less
than 0.5A
4. Lenght of video cables (75ohm) ≥50m.
5. We do not recommand connecting transmitter and receiver to one power
supply adaptor. Connecting a few receivers to one power supply adaptor or
a few transmitters to one power supply adaptor is allowable.
V- video signal input A.2 - Audio in of channel 2
GND –video signal minus GND – power minus
A.1- Audio in of channel1 1 + 12V – power supply 12V
WARRANTY:
CAMSAT grants 24 months warranty for 5.8GHz transmitting – receiving set
named TCO5807m.
1. The warranty covers product’s defects caused by faulty components or
workmanship.
2. The product must be delivered to sales point or to manufacturer directly,
along with proof of purchase, problem description and this warranty
card. Shipping costs are to bear by claimer of complaint.
3. Defects disclosed during warranty period shall be removed free of
charge within no longer than 14 working days from the date of delivery
of claimed equipment.
4. The Warranty does not cover:
ASSEMBLY:
Mount transmitter on a stable basis using screws. Screw antenna or antenna
wire into antenna port SMA. Place antenna in direct visibility of receiving
point to get best possible quality of transmission. (Note: Transmitter`s an-
tenna has to be in a line of sight of receiver`s antenna). Mount receiver ac-
cording to above instructions.
Connect video signal cables and power supply cables according to descrip-
tions on the PCB. Set required channel according to the Table below. The
polarity and channel number must be same for both interacting trans-
mit/receive devices. There is the adjusting potentiometer within transmitting
part for setting the video-contrast, which enables proper matching of signal
source connected.
RECOMMENDATIONS :
1. Bigger systems, using more then one set should be started one after another (not
all in the same time).
2. Due to causing clutter we do not recommand using pulse power supply
adaptors different to the one recommended by manufacturer f.e. ZS12/1A.
3. Recommended power supply adapter: transformer, stabilized, 12V not less
than 0.5A
4. Lenght of video cables (75ohm) ≥50m.
5. We do not recommand connecting transmitter and receiver to one power
supply adaptor. Connecting a few receivers to one power supply adaptor or
a few transmitters to one power supply adaptor is allowable.
V- video signal input A.2 - Audio in of channel 2
GND –video signal minus GND – power minus
A.1- Audio in of channel1 1 + 12V – power supply 12V
WARRANTY:
CAMSAT grants 24 months warranty for 5.8GHz transmitting – receiving set
named TCO5807m.
1. The warranty covers product’s defects caused by faulty components or
workmanship.
2. The product must be delivered to sales point or to manufacturer directly,
along with proof of purchase, problem description and this warranty
card. Shipping costs are to bear by claimer of complaint.
3. Defects disclosed during warranty period shall be removed free of
charge within no longer than 14 working days from the date of delivery
of claimed equipment.
4. The Warranty does not cover:
www.cctvireland.ie
Lo-Call 1890 866 900
[email protected]